Complete DIY guide to building an infinite sustainer sustainiac-Part 1 of 5-Proof of concept

Подписаться 772

Просмотров 22 тыс.

50% 1

The only complete DIY guide to building an infinite sustainer sustainiac for your guitar-Part 1 of 5-Proof of concept
13:22 is where it came together if you want to jump there.
I am going to make more videos shortly that will answer all questions.
Video 1: Proof of concept
Video 2: How to make a better driver pickup-coming soon.
Video 3: How to reduce the size of the honey tone amp and get it into your guitar without too much BS-coming soon.
Video 4: The finished product and was it worth it all?-coming soon.
Video 5: I’ll probably need to tell you something else important lol-coming soon.
There are allot of videos, websites, and forums that give you pieces of the puzzle, I am going to try to put it all in one place. Honestly, look at the sustainiac website, there’s more info there than they should give out, they practically tell you how to build the thing there. My approach doesn’t use science or too much research, but I’ve taken all the pieces of the puzzle scattered all over the place and assembled it as you see here in a cheap, but practical way to get your own infinite sustainer that you built. Will it be better than the real deal, probably not, but will it be cool and fun!
Please share with others what you create and what you learned.
Links with info:
How to add your own pots to the Honeytone amp/excellent info about the amp:
www.angelfire.com/music/harmon...
Websites with the pieces of the puzzle:
sustainiac.com
www.harmonycentral.com/forums...
theawesomepowerofrockets.blogs...
www.diystompboxes.com/smfforu...
music-electronics-forum.com/s...
www.projectguitar.com/forums/t...
www.researchgate.net/publicat...
www.thegearpage.net/board/ind...
Helpful videos:
• diy sustainer pickup /...
• Custom DIY Guitar Sust...
• Sustainiac Pickup DIY ...

Авто/Мото

Опубликовано:

29 мар 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 39

@NicheAsQuiche 4 года назад

This is amazing, thank you so much for making this so clear, I've been looking for ages for how to do this but all the sources I found are so unclear and not explained well, your video is perfect at explaining everything. Thank you!!

@amateurism1 4 года назад

Thank you for the kind words, it took me a lot of reading and effort to figure out just how simple the device truly is, the rest of the videos are coming promise.

@FBGOODIE 2 года назад

Thank you for sharing your awesome job!

@georgerobartes5989 2 года назад

You are building an induction motor . A good circuit to drive the motor is the " Ruby " amp based on the LM386 op amp on one of the forums Run Off Groove . You can use the Ruby to drive a Piezo which are commonly used as buzzers , speakers etc and whack one on the back of a humbucker. You also need around 30 ohms to drive the induction motor type you built as there is no relation to driving the output of a speaker to controlling a wound induction motor , and its not like you are dealing with tube output transformers , this is solid state and the impedance is not critical .

@jaqueslagerweij6882 2 года назад

Love the vid.i mine mine almost the same. Cant got over the fact Peter Steele made a build video. Your voice is deep dude.

@anthonypape6862 2 года назад

This is very cool and thank you for all of the work. It helped me learn a lot, first and foremost of that being I have no business trying to replicate this. I ordered a used schecter with sustainiac for $600. It’s awesome.

@amateurism1 2 года назад

Thanks, I've been unable to replicate it and have it preform well, I honestly would grab a used guitar that had one, I will if one ever presents itself for sale to me. Why Lord can't a Kenny Hickey schecter appear before me for 300 bucks?

@anthonypape6862 2 года назад

@@amateurism1 Because it’s a Kenny Hickey. You can find a used excellent condition C1 Schecter in Green for about $600 with nearly same exact specs or C-6 a with not quite the same specs for $400. Or whatever you did to save that $300 just do it 3 more times. I wish I wouldn’t have settled for so much crap and just waited. Although my best sounding and by far easiest to play guitar is 1999 Ibanez RG 570 that I thought I might try painting. It’s beat to hell but I just can’t do it. During the COVID lock down I learned I am no handyman. Pre Covid I had a screw driver. After lock down I had pneumatic impact drivers and useless projects that have stalled. Learned my limitations.

@rival6676 2 года назад

your work is very good bro. please make a sustain coil pickup driver tutorial 🙏

@amateurism1 2 года назад

I got to make a lessons learned video, I'm not as successful as I'd like you all to believe, stay tuned.

@martysradioshow5979 Год назад

wow its nice

@biroesustainer573 3 года назад

Bagus... Saya telah mengerjakannya

@Reprodestruxion 3 года назад

Any idea how to do this with a German kemo amplifier without a woofer?

@thiagoavila5329 3 года назад

Does It works on B and high E strings ?

@rofflestomp684 7 месяцев назад

For all that work, I would just buy the pickup set for about 300 bucks. I get rolling the project though. That's cool fun.

@bgadzi333 Год назад

The first driver is correct but you need to change the wire gauge inorder to operate.

@infectionsman 4 года назад

Hello, this is an interesting initiative of yours. However I noticed several possible problems with this design. You need to use much thicker wire, something like 0.2mm diameter or less. 42 gauge (AWG?) wire is way too thin, that is the stuff you have in a regular guitar pickup. Also, I think 8 ohms too low impedance. Maybe around 40ohms would be better, since you likely intend to run this off a 9v battery. Now, I also noticed you said you were using the middle pickup. This is a bad idea. You need to use the bridge pickup to max out the distance between the driver coil and the sensing pickup. This will minimize squealing.

@amateurism1 4 года назад

I agree with all you say, but the wire gage, if I use that large of a diameter wire, the impedance/ DC resistance will be too low, I don't think you can wind 40 ohms with that large wire, unless you use like a mile of it and make the driver pickup huge. That is one reason why I chose the wire gage I did, to a degree. I could be wrong, I'll give your idea a try in my next vid, but I'm ultimately trying to match the impedence of the honeytone amp so I don't burn it up.

@infectionsman 4 года назад

Yes of course, I just winged the numbers. But still thicker than 42 awg. 0.2 mm would be something like 32 awg if I recall correctly and you could get maybe around 8 ohms with that. So like I said, probably a thinner wire than that. I think the amp should be fine, SS circuits dont tend to be too picky with impedance as long as youre increasing it since you are lowering the current draw over the OPamp anyway. However If you go under the rated impedance youre basically shorting it more and more which will destroy it.

@amateurism1 4 года назад

infectionsman I am reading between the lines now, the more winding the better, or so one would assume, I have some 30 ga stranded wire I can use, I'll add an 8 ohm resistor in the windings to get an appropriate DC resistance; I’ll do this in the driver pickup vid and see if that has more driving power,; that actually might work really good, thanks, sorry I didn't quite see you point until now. I must note, I was playing with the piece of steel and the 42 ga. Wire you saw in this vid, it's plenty strong to get the job done. I assume that I'll reach a point where a driver pickup gets too strong and negative affects are heard in music, we'll soon see.

@infectionsman 4 года назад

It is possible to use 42 gauge and wind it to a higher impedance, but like I said it should be more efficient with an appropriate gauge. I dont know about the resistor, sounds counter intuitive.

@timanderson5417 4 года назад

ever tried on a bass? Should I give it a shot?

@amateurism1 4 года назад

Yes! Don’t let others hold you back, I initially was like, “a bass string has too much mass for this to work,” that thought is all the more reason to try it! You can try without any permanent modifications, let us know if it works, make a video for us with the results.

@addiefebrianto5650 2 года назад

I have made a pickup driver, but the sound of the vibration penetrates the bridge pickup, why?

@amateurism1 2 года назад

Is the driver and bridge pickup connected in any way to the pickup selector switch?

@addiefebrianto5650 2 года назад

Yes..(ruby fetzer)..

@amateurism1 2 года назад

So... I have found that many guitar switches have very poor offness; look it up; it's a thing. You might need to invest in a different switch, the signal is bleeding from the driver amplifier to the bridge pickup though the switch. Keep in mind that those switches see a few millivolts and milliamps from the pickups when operated as they are designed to, put a 9v device on it and they no longer are in their intended range of operation. Most Gibson three position switches work well, but any 5 way or blade or PCB switch is not going to work. Is that the only problem you have?

@addiefebrianto5650 2 года назад

what pre-amp schematic you used?

@amateurism1 2 года назад

I didn't really use a schematic so to say, there is only really a handful of possible integration techniques. I don't know if my suggestion regarding the switch helped. I'm using a 2w amp I bought off eBay for a cigar box amp. The driver (neck pickup) goes to the 2w amp speaker output, the bridge pickup goes to 2w amp input. With the 2w amp I can hear there driver via the bridge pickup though the switch, I may try an optocoupler.... But my driver pickup needs some work still before I try that.

@RobertLongM 4 года назад

Potted? Is that waxed?

@amateurism1 4 года назад

Whatever we end up using as the driver pickup will need to be potted in wax. I use paraffin from the crafts store, candle wax is fine too. The enamel coating on the copper windings needs to be protected and held in place so they don't rub on things and each other.

@RobertLongM 4 года назад

@@amateurism1 goes to show - in all my research Not 1 article said to do that... 🤔 Unless it did. Thank you for the tip!

@medmusic7977 Год назад

Dude just buy one off ebay, what waste of material and lack of search

@amateurism1 Год назад

Holy moly only 55 bucks! That wasn’t on eBay when I started this kind of sort of waste of time. Still need a driver pickup, is there a kit you know of that has the driver included? If yes, please let me (us) know. Agreed.

@ioodyssey3740 2 года назад

waste of time

@amateurism1 2 года назад

I agree, I can't it to work well enough to make further value added videos. I'll make a lessons leaned video soon and hopefully someone smarter than I can go farther or all the way.