Cub Cadet XT1 console removal for switch replacement plus solenoid replacement. 

I'm so glad you showed the location of the starter solenoid. I was going to try to trace the power wire from the starter to find it.

Thank You very much. This was a great help. My choke /throttle cable just broke under the dash cowling and it is stuck in choke position.

Thank you for this explanation on how to remove the cowl and access the ignition switch. Perfect!

Great demo on these two items! What a design nightmare! Way to much work to replace the ignition. I just took my vibrating cut tool to the old switch. When you look at the new switch, it is easy to see where to cut the keeper tabs of. Just slide the switch to the left when you cut the right side and visa vesa for the left side. This will prevent you from cutting the plastic cover that hold the switch in. Old switch out in 5 minutes.

Thanks for the video. My reverse mow only worked if I played with location of key. I pulled switch out, took it apart, and cleaned up the contacts. Seems to work now! It was a bit tricky to reach in and push release tabs on plugs. I tried just pulling but plugs wouldn’t release. Scratched knuckles are cheaper than a new switch though! Thanks again.

Thanks for the video, saved me time and some frustration while I had to replace my PTO switch

Thanks man. Appreciate you taking the time to make this video. It helped save me some time.

Thanks for the instructions. Switched out my solenoid with your guidance.

Appreciate you makin the video! I like workin on things but i suck. These videos help a ton! Now i got a silinoid thing to replace haha.

When replacing the ignition module, it helps to pull the grommet loose that holds the wire bundle to the frame under the gas tank. That provides more slack in the wire to work with getting the new module plugged in. It's almost impossible without doing that unless you have tiny hands.

Thank you. This is a project I have for tomorrow!

Thank you for posting! It did help me!

Thank You for information and advice Kinda a pain in the butt for a newer mower

My starter wire is smoking now. Needed this video. Think it's the switch

Thank you, you saved me a lot of time. Thank again

Awesome job thanks for the help

on cub cadet mowers, there are more and more videos about parts replacement..I own this type of tractor..just bought it.. I also have a sears craftsman 14 h.p. tractor, for nearly 20 years..the only thing I've replaced on old tractor..sears.. are the two blades and gas tank..nothing else.. guess cub cadet won't last me anywhere near 20 years..with frequent part replacements.. I'll always have a new tractor 🚜..

Great video! Thanks

Thank You!! Very Helpful

Thanks that helped me get the gas tank off! Some kids put dirt in the tank!

Outstanding! Thanks!

Hey I like your video man that helped me out tremendously

thank you buddy. really appreciate that.

TY Buddy

Saved my ass man, thanks!!!!

Thank you.

I do not have display info on my xt1. The 20amp is good. Wanted to take apart to see if there is a hidden fuse by the display. Thanks for this video. Will open up, but short term - is there a fuse that controls if you get display info - run time, battery volt, etc? Thanks.

Freakin’ excellent!!

Thank you

Could someone tell me how the wiring for the two clips beneath the main connectors of the solenoid go? One is red, the other green/ blue. I've seen two different diagrams online and each have them both ways... Currently, I have the red under the red... on the left, blue/ green/ ground on the right (looking at it from the perspective of the steering wheel to the back of the mower).

👍

Ok, so I got all the bolts taken off, removed gas cap, disconnected ignition switch and time sensor, but how the heck do I get the choke thingy off. 😭😭😭 There is so much build up from squirrels and birds I can't see. Do I have to remove the choke from the front to take the entire dash mount off?

I REPLACED THE SWITCH AND IT STILL WILL NOT CRANK. IS THERE MORE THAN ONE FUSE ON THESE CUB CADET MOWERS.

Mice issues?!? As my grandsons say, 'Papa's shed is where mice go to DIE!! Couple of snap traps, problem solved.