Cura Slicer V4.9 plus Cura Arachne Engine Sneak Peek

Подписаться 297 тыс.

Просмотров 71 тыс.

50% 1

In this episode, Chuck shows the new features of Cura Slicer 4.9. Plus he gives you a sneak peek at the new Cura Slicer Arachne Engine on this week's Filament Friday.
Cura Slicer V4.9:
ultimaker.com/learn/increased...
Cura Arachne Engine now in Beta:
support.ultimaker.com/hc/en-u...
**** Support the Channel *****************
Financial Support through Patreon:
/ elproducts
Support the Channel here and Shop at MatterHackers.com and you automatically donate to the channel at no cost to you:
bit.ly/1Ugcijp
Buy thru this link to Slice Engineering for the Best Hot Ends:
bit.ly/3yuyuze
******** Ender 3X / Pro 3X ***************
Ender 3X: bit.ly/2P9O6qX
Ender 3X Pro: bit.ly/3cnnpI0
***** Creality Ender 3: ******
amzn.to/3fSIISy
From Banggood : bit.ly/2wfD5Ia
Creality Official Reseller Comgrow: bit.ly/3hDTvSf
Bundle From MatterHackers: bit.ly/2ZvGLnE
***** Creality Ender 3 Pro: *****
amzn.to/2QUjRUL
From Banggood.com: bit.ly/2DBG0AI
Creality Official Reseller Comgrow: bit.ly/3hET7CL
Bundle From MatterHackers: bit.ly/2FuKFpu
***** Creality Ender 3 V2 ******
Amazon: amzn.to/3ioLVsC
Banggood: bit.ly/2MQ5VGM
Creality Official Reseller Comgrow: bit.ly/3tTrGdp
CHEP Cube 3D Print: bit.ly/3gH4l9D
CHEP PAWN: bit.ly/3pHYE08
CR-10 V2
Amazon: amzn.to/2C2naiy
Creality Official Reseller Comgrow: bit.ly/2WwT8gz
Banggood: www.banggood.com/custlink/G3G...
******* Silent Driver Boards ***************
Creality 8-bit V1.1.5 Silent Stepper Board:
amzn.to/2YPM0Nh
Creality V4.2.7 32-bit Silent Stepper Board:
Amazon: amzn.to/34GhY31
Creality Official Store: bit.ly/2XrAT0k
Banggood: bit.ly/3ebPSzP
SKR Mini E3 32-Bit Silent Driver Board V2.0 :
Amazon: amzn.to/2XDY9Wi
Banggood: www.banggood.com/custlink/KDm...
**** Ender 3 Glass Bed ****
Amazon: amzn.to/3tYea7m
Banggood: bit.ly/3lSDVTH
Creality Official Reseller Comgrow: bit.ly/3rqR9bx
Creality Official Firmware:
www.creality.com/download
Nozzle Removal Tool:
Palm Ratchet: amzn.to/3u6ncm7
Premium Version with Rubber Grip: amzn.to/3qPs3pB
1/4'' Socket: amzn.to/2OjdHdg
Creality Ender 3 Parts/Upgrades
-------------------------------------------
X-Axis Tensioner
amzn.to/38BKbYP
Y-Axis Tensioner
amzn.to/2PhOdhi
Chuck's Favorite EZR Extruder:
bit.ly/2rlKCpp
Creality 8-bit Silent Stepper Board: amzn.to/2YPM0Nh
Cap Tubes & Couplings: amzn.to/2Vf8BCf
CR10/Creality Ender 3 Nozzles: amzn.to/2m39K1y
CR10/Ender3 Silicon Heater Block Cover: amzn.to/3sfDG7s
Solder Sleeve Kit: amzn.to/2Pqqngm
Creality Ender 3 Fan Set (24v): amzn.to/38u9aOl
CR-10 Fan Set (12v): amzn.to/2PrcCxK
T-Nuts Kit: amzn.to/2LsQZg8
Screw Kit: amzn.to/2Va8uGK
Temperature Meter Used in Videos: amzn.to/2JpUJOC
Screwdriver set used in Videos: amzn.to/2PbWocM
Creality Ender 3 Upgrade Package (Extruder, Silent Board & Capricorn Tubing): bit.ly/2MNvmcs
Cura Slicer Profiles:
www.chepclub.com/cura-profile...
Cura Download:
ultimaker.com/software/ultima...
CHEP Prusa Profiles:
www.chepclub.com/prusaslicer-...
CR-10:
amzn.to/2JDO9oP
From Creality Official Reseller Comgrow: bit.ly/2PF01uW
From Banggood : bit.ly/2udpwaj
**** Support the Channel *****************
EBAY USA: ebay.to/1wtxfiU
EBAY UK: ebay.eu/2qdC5iy
EBAY Canada: bit.ly/2qdGRwh
Support the Channel here and Shop at MatterHackers.com and you automatically donate to the channel at no cost to you:
bit.ly/1Ugcijp
Buy thru this link to Slice Engineering for the Best Hot Ends:
bit.ly/3yuyuze
Note:
As an Amazon Associate, I earn from qualifying purchases.
****************************************************
Filament Friday Sticker:
Send Self Addressed Stamped Envelope to:
Electronic Products
PO Box 251
Milford, MI 48381
****************************************************
Chuck's Arduino Book:
amzn.to/3tA31JP
Intro animation by Pablo Licari based on Filament Friday Logo by Brian Carter.
*************** Free Filament Friday Sticker **************
Send Self Addressed Stamped Envelope to:
Electronic Products
P.O.Box 251
Milford, MI 48381
**********************************************************

Хобби

Опубликовано:

15 апр 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 168

$@fractalengineering$

@fractalengineering 3 года назад

That Arachne beta is outstanding; it's been my primary version since it came out. I print a lot of tiny functional parts with intricate features and this variable line width is doing a fantastic job at cleaning up the path. Works just as well as S3D in many cases. Very excited for the merge

@redrocket23 3 года назад

I’d just like to thank you chuck. Your tips, guides, reviews, and everything in between is what has helped me come into this hobby. I absolutely love it and I wouldn’t be able to get into and enjoy 3D printing without the help of your videos.

@BenChilds 3 года назад

As a guess, the odd infill pattern on the cylinder may be due to the old engine trying to solve the infill along either X or Y as much as possible (Sensible to only move one axis at a time as much as possible to prevent inaccuracies with material placement). It then looks like it's trying to approximate by "Squaring the circle" as much as it can instead of tracing the arc. If you look closely, one part of it has it doing parallel lines until it gets infeasible to continue due to the narrowness of the direction of travel (Possibly controlled by minimum infill length settings) then the less dominant axis takes over and it can more readily trace the curve until it reaches the other side and it goes back to it's funky ways. I see this as being a huge improvement: Time saved for more efficient tracing. Les vibration introduced on model because it's not doing so many direction changes - less chance for a tall model to work itself loose. More efficient use of material / less chance for blobbing from over extrusion. EDIT: Less retraction so less chance of extruder breakage of filament.

@andrzejpolny3427 3 года назад

6:50 woah, finally. I really hated that weird infill

@JohnKlosner 3 года назад

Resaving as a .3mf instead of .stl file has fixed the zigzag line issue for me as well. Just a handy tip for everyone on old versions.

@toddcoello6461 3 года назад

Thank you for renewing the infill thing..

@mcorrade 3 года назад

wow CHEP thanks a million. I just used the new beta engine and the difference is crazy good. Not only do the prints come out way better but also a bit faster at least the few tests and real world prints I've done! 4.9 with the new engine is the way to go!!!!

@TheRock-re2ro 3 года назад

I have to say that I really like your video's , they are well displayed with the zoom so we can see properly and you get to the point with no long boring stories. Thanks

@signalrk 3 года назад

The things I can do with per model settings has been amazing. Thanks for the original info and continuing to educate about it!

@dadmezz4024 2 года назад

Thank you Chuck. I like that you back illustrate some options for those of us who are reluctant to update to newest versions of Cura and have missed a few options. I have a V15 and a newer version 4.1 to play with if I need it. Your reviews help a lot for this reluctant user.

@reneestrada1148 3 года назад

Awesome! We waited for these features for soo long...

@ScottLeslie 3 года назад

Any very detailed, yet quick video! Thanks

@soggynode 3 года назад

Nice preview for the upcoming Cura. I like that new line type mode, especially the seams. I use the support blocker feature a lot when I'm testing new functional models. I change the blocks to a cutting mesh and adjust the settings so I can turn off features I don't want to print. Saves hours of printing and meters of filament when you're trying to fine tune the size or shape of a particular feature in a model. Great content as always.

@ThysaniaAg 3 года назад

Thanks for the review and observations! Really interesting and useful!

@avejst 3 года назад

Great news Thanks for sharing your experience with all of us👍😁

@aarondavalon8985 3 года назад

Deeply appreciate this informative video, cura is my go-to slicer.

@havenview 3 года назад

The crushed inner walls issue is often caused by the mathematical discrepancies that processors have with floating point numbers. When you code with floating point you cannot properly use the "equals" operator, you use programming techniques to effectively ask "near enough equal to" The work around is often to drop the inner line width by a really small value, say to 0.39 or 0.38 instead of 0.4 This will make near zero difference to the amount of filament extruded for each section (and they are inner walls anyway) but it will spoof the slicer into thinking the final inner wall is "near enough equal to" the available space in the model

@fierceflyer5 3 года назад

Very helpful video as usual. Thanks

@ronm6585 3 года назад

Great info. Thanks for sharing.

@JohnSmith-gt7tg 3 года назад

Great video, thanks! Those messed up inner walls are the main cause for stringing when I print with TPU, so I'm really looking forward to the new engine.

@macEboy 3 года назад

Thanks Chep!

@qwer.ty. 3 года назад

Thanks !!

@MrBaskins2010 3 года назад

This new slicer engine which I have been using in alpha for almost two months on both my machines is incredible. Faster slice times and higher quality prints all around

@MCsCreations 3 года назад

Pretty interesting indeed, Chuck! Thanks a lot! 😊 Stay safe there with your family! 🖖😊

@KarriKoivusalo 3 года назад

I once had that issue line width more than double the print time of a piece, good thing it seems to be sorted out.

@cache4pat 3 года назад

Awesome Video

@ProgrammerEA 3 года назад

I think this will be best version on of CURA Slicer.

@sysghost 3 года назад

Just tested Cura's Arachne Engine version. It's a huge improvement on walls. It also finds better spots for the seam

@kendokaaa 3 года назад

Being able to see the seams will be really useful. I normally have to enable coasting to have a visual representation of it

@TYGAMatt 3 года назад

That's exactly what I do, so yes, being able to see the seams will be great

@dbcrypto6142 3 года назад

Ive been using 4.9 for a month or so and no issues yet

@3rdpig 3 года назад

Good info, thanks. The new engine should help. Try creating a flat disc say 25mm in diameter with a 5mm hole in the center, one layer high. Slice it in Cura with concentric lines and look at it. Then slightly change the outer diameter, say to 27mm and slice again. Cura has a lot of trouble getting this right, you have to tweak the line width each time you change the outer diameter if you want a nicely printed flat disk with no overlaps, zig zag lines or missing lines.

@ubergeeknz 3 года назад

That's interesting. I've definitely had problems printing thin walls (1 line width) on Cura due to this behavior and could not figure it out. Other slicers didn't have the same problem. Trying to make the wall a bit thicker always resulted in other strangeness. I'll have to try the same prints with arachne engine and see how it goes 👍

@bruceyoung1343 3 года назад

Hmmmm. Thank You

@cam-joh 3 года назад

great video! The new slicer engine Arachne is actually pronounced "A-rack-knee" like the Greek myth about the spider seamstress; pretty fitting name for a slicer that weaves filament together to create a finished piece.

@mikin.6595 3 года назад

Tha man! :)

@housinit 3 года назад

Thanks CHEP! Was wondering what had changed in 4.9 Beta. So funny how people can only say the name Arachne right about half the time. Really interested to see if you make any changes to your Magic settings for Creality. I use the CR-10 v1, modified a bit, but your settings are an awesome starting point.

@sfrskz 3 года назад

That solid layer will leave a mark i think

@s8nlx661 3 года назад

Apparently alot of the reason for this new release was because of the large request for Mingda profiles, rightfully so. The rock 3 pro is hands down the best printer on the market. I was blown away by how good it was. I've got every great budget printer (ender5 plus, cr10s pro v2, artillery x1 v4, cr6 se etc) and it absolutely blows them all away. Super impressive machine and glad to see it getting a well deserved spot in Cura. Can't wait for the new cura 4.9 cus the 4.8 was packed full of bugs. Thanks Chep for another great video!......and P.S. Chuck please give the Mingda Rock 3 Pro a review. You'll definitely love the printer, truly top notch.

@makewithmegma 3 года назад

❤👍

@omniderb8563 3 года назад

Thank you for the great informational video. How can I make Cura 4.9 open with the same front view everytime? Pulldown menu/view/front view.

@Chrissi33004 3 года назад

Finally a new engine for Cura! I really hate the quirks of the current one Like the zigzag you showed Or the non-printing of thin (sacrificial) layers And similar

@colinfielder6695 3 года назад

Great review Chuck, does Cura have a profile for the new Naomi 3D Print Mill?

@Chriss_Workshop 3 года назад

Does the beta also add more printers to their supported list? Like the slew of ender 3 types that have popped up lately, or the cr-30?

@williamhargraves8813 3 года назад

I've been using cura 4.9.1 for the last few weeks and is pretty simple to use I have only had a few failed prints and most of the time it was machine error, like the plastic extruder breaking and or poor quality filament

@johngrossnickle8874 3 года назад

How do you get the toolbar on the left of cura? Only had my ender 3 pro and cura a week so still learning....Love your video content.

@omniderb8563 3 года назад

I’ve been using Cura 4.9 for a few days. Very happy with it so far. However, I find problems with Custom Supports, Cylinder. Cannot change support pattern or density. When I choose custom supports, the support menu opens up so that I can make changes, but the changes don’t have any effect on the supports.

@mkuebbeler 3 года назад

Looks like Prusaslicer now

@mannybhogal 3 года назад

Is their an option to select ender 3 v2 as printer now.

@hydromakers 3 года назад

In Ideamaker! and in per-layer setting you can set the (top surface wall line count to 1, regardless of the previous wall line count). How can i do the same thing in Cura? Thank in advance.

@aaronsteers 3 года назад

I don't see the option to add the support blocker? Is there a setting that hides/unhides that?

@stevemay4180 3 года назад

Tried out Cura 4.9, was ok with it till I noticed something out of the ordinary. Was setting up after installing Micro-Swiss direct drive. What I noticed was when printing my extruder temperature was changing. My PETG runs at 240C, that's how I set it. About 2 minutes into the print it went to 260C then after awhile to 255C. I thought I had wxtruder problems. I changed... hotend, main logic board. to no avail. Out of the clear blue I edited the gcode, guess what... it was changing my temperature. So I edited out the changes and its ok. How Come? This was on the Cura XYZ Cube. Any ideas>

@drew899 3 года назад

Hey chep, is there any reason that the tolerances in my prints got messed up when I switched to a .6mm nozzle, I set cura to .6mm nozzle but it was like it was still printing through a .4mm

@drxym 3 года назад

I've always thought Cura was more powerful than Prusa Slicer and a bit more organized but god is it slow. Slow to start, slow to slice and memory heavy. I find myself using Prusa simply because is so much quicker to do something. The main thing I like Cura for is tree supports so it has that going for it.

@oimate3 3 года назад

Do these newer versions support the sidewinder? I got cura 4.6 working well with mine and not sure if I want to change things up

@rc4625 3 года назад

I have an issue when i change the infill for certain parts of the print. The part that doesn’t have the support block is fine. But the part where the support block is. There is a gap between the walls and the infill. I saw in your preview in cura that you have the same issue. Has anyone over come this?

@alanloosley3262 3 года назад

Would you recommend Ender three max for beginner thank you.

@HumbleSaltFarmer 3 года назад

Did it fix the issues that 4.8 had? Like layer inconsistency/gaps?

@smorris12 3 года назад

I wonder if the new engine is rendering in G-code curve commands to lose the stuttered inner lines? I've been using ArcWelder (thanks for the heads up on that one, Chuck!) and it's been noticeably strimming out a lot of straight line G-code.

@JelleSpijker 3 года назад

No, we don't generate G2 and G3 commands with Arachne. All paths generated by Arachne are still G0 and G1. They're are now only positioned differently and they can vary in line width along a path, so these fill the shape more efficiently.

@smorris12 3 года назад

@@JelleSpijker Fascinating. Thankyou for the insight. As a software engineer I've often wondered how Cura deals with such downscaling

@mcorrade 3 года назад

Chep hi, don't know if this is a bug or a setting in the new Cura Beta engine, but when I eject the flash card after completing the slice it shuts down the program where the version 4.8 simply ejects the card.

@remcoburema7001 3 года назад

This is indeed a known issue, should be fixed for 4.9.0-final (maybe 4.9-beta as well, but I'm not in a position to look that up easily right now).

@siddhesh_bhogle 3 года назад

hey my CURA 4.8 version not showing simulation preview at bottom, how to enable this setting? I already tried to reinstalling it but problem still persists.

@vansrvaccessoriesinc.9817 3 года назад

I have two file that I print with a ender 3 pro I was wondering if I could send you my files to look at an see why it take so long to print. I have watch most of your video and it help some, Am i using the right printer, pla , temp....Thank you

@Burak0015 3 года назад

Hey Chep, I am using an ender 3 pro for a while I upgraded extruder, board and bed however I have a problem and I cannot fix it. I calibrated everything filament, extruder, esteps however none of them could fix my problem my problem is whenever I try to print something with a moving part. parts always fuse together. I made tolarance test but it could only pass 0,5, 0,4 and stuck at 0.3 any suggestion what I can do to fix this? When I decrease extruder multiplier it makes it possible to move 0.3 however it also makes the print weaker so I do not think that is a solution.

@FilamentFriday 3 года назад

Sounds like overextending but you calibrated so I’m not sure.

@javelinexile 3 года назад

This version popped up as an update and I installed it. The line type selection for Starts isn't there in fact where the drop-down where it says line type instead is it says compatibility mode. Maybe because this file was sliced in Cura 4.8 Before?

@FilamentFriday 3 года назад

Under preferences > general. Check if compatibility mode is enabled.

@javelinexile 3 года назад

@@FilamentFriday yes thank you it is. This is an older machine and my Quatro video card doesn't support the right flavor of OpenGL

@mattlogue1300 3 года назад

You didn't talk about the two new buttons under support blocker

@JelleSpijker 3 года назад

Those are plugins and not distributed with Cura.

@AndrewAHayes 3 года назад

Chuck when I start a print my BL Touch probing starts but the nozzle is in the position where the probe should be, is this because I have the APPLY EXTRUDER OFFSETS TO GCODE set to positive on the page where you set your start and end Gcode in Cura or is it the firmware that has been set incorrectly?

@SolBro2 3 года назад

That would be in your firmware. I just upgraded to a bl touch and that's where I had to adjust for the x y probe distance in marlin.

@gadjetsvideo 3 года назад

Great video but unfortunately 4.9 just crashes on my PC whenever I open a file..... back to 4.8 I suppose!

@crashlaw 3 года назад

Keep Wall Thickness, Wall Line Count and Top/Bottom Thicknes.. and add infill...

@Rebar77_real 3 года назад

DM's will have fun scrutinizing die for thicker infilled sections with x-ray scanners.

@LenordeFPV 3 года назад

This new engine looks really promising! Did they optimize the printing order to reduce travels ? I feel like I see some nonsense travels sometimes...

@Crazyates11 3 года назад

There are two options you can search for: “Optimize wall printing order” and “Infill travel optimization”

@LenordeFPV 3 года назад

@@Crazyates11 Thank you! I already use both options. But when slicing a cylinder for example, it will start the skirt from one side, then it will travel to another side for the cylinder walls, and finally a third travel for a feature next to the cylinder. All of these travels could be greatly reduced if it starteed from the same point of the circle everytime. On more complex shapes, it is even more obvious to see the nozzle travel from one side to the opposite, then coming back almost next to the first point...

@JelleSpijker 3 года назад

We worked on the algorithms for generating and placing walls with variable line widths. A side result is that these might now be open lines and not closed loops. That could mean that you will see a slight increase in the number of travels. But keep it mind that the total time a printer travels is nothing compared to the time it actually print. So optimizing these moves won't bring that much time reduction. While optimizing wall line placement will bring greater print time reductions.

@LenordeFPV 3 года назад

@@JelleSpijker Thank you for this explanation! I just tried Arachne, and it is awesome for cylindrical parts. Even with these additional travels for open lines, the print time is reduced because the infill is much more efficient. I was pointing out the starting point of a closed loop that is sometimes far away from the last printing head position. The goal would not be to reduce the printing time but rather the impact of oozing/stringing. When it crosses the whole print, it can leave material at an undesired location. My example is very specific, and I'm still not an expert in 3D printing, so I don't know if this case is really an issue. Also, if I understand correctly, it is not possible to "see in the future" and look at the next feature to print before deciding where to start a loop.

@JelleSpijker 3 года назад

Yes, absolutely correct there are more benefits then just a print time reduction. But unfortunately we have to prioritize what we work on and since there are already measures in place to reduce oozing, travel optimization is a bit lower on our backlog. Especially since these types of problems are hard to solve for all scenarios. But these are also the interesting math problems to solve, so no worries we developers will ofcourse try to optimize them anyway.

@angelinajoy3084 3 года назад

Where I can send some picture with my 3D printing for a model. I am not sure what I do wrong on Cura but the model is not looking good.

@CollinBaillie 3 года назад

Thumbs up, if you watched both videos!

@13FPV 3 года назад

Hey Chep! I am trying to port my cura profiles from 4.6.1 to 4.8 but the profiles only work when I click on a higher nozzle size. This happens with all versions higher than 4.6.1. I would like to update but I need to port my profiles! Any idea?

@FilamentFriday 3 года назад

Never heard of that. My transferred fine.

@13FPV 3 года назад

@@FilamentFriday When I import the profile, I get this warning. Warning: The profile is not visible because its quality type 'draft' is not available for the current configuration. Switch to a material/nozzle combination that can use this quality type.

@marcofranzini8610 3 года назад

Dear "CHEP", I have tried the arachne alpha edition, and I appreciate the afforts Ultimaker team made. Specifically the inner walls are clean, without zig-zag. But there is another point: THE SKIN IS ABSORBED IN INNER WALLS IN THE time info preview. Generally is a much better engine because require less acceleration, and less retraction, and the quality and time of the printer are highly impacted. It will not implemented in the 4.9

@israelSalles 3 года назад

Já tem a confirmação da Two trees bluer, imprimi usando o novo cura mesmo com o perfil deles, não ficou bom.

@mikepowers9486 3 года назад

Anyone know how to make the raft bigger? I can't seem to figure it out with 4.9.1

@bortasha 3 года назад

Do you mean wider? I thing "raft extra margin" will do it. After you click on "raft", it is the first option.

@user-lr1om6xm4w 3 года назад

What to buy ender 3 v2 or cr 10 mini?

@FilamentFriday 3 года назад

V2. Mini is a bit old.

@Clell65619 3 года назад

Hmm. A goatee? Chep from a mirror universe?

@hydromakers 3 года назад

Why do you haft search for seams

@jameswiz 3 года назад

Would you be willing to look at a Marlin config for me please? Im trying to help someone else and their BLtouch doesnt seem to be working. I don't see an issue and would like another set of eyes.

@CanadianJedi 3 года назад

Just updated to 4.9 but I am still getting these little jagged zig zag sections. Any other solutions?

@mrselenio 3 года назад

yeah me too, change "Wall Line Count" for a higher number, I tested this with a part just like the one he shown, and I had that setting with 2 lines, when I changed it to 3 like he has in the video, it got fixed, so add wall lines until you don't have that issue anymore I guess, he also mentioned line width, so try that too

@CanadianJedi 3 года назад

@@mrselenio worth a shot. Cheers

@yvesinformel221 3 года назад

the fix is not with version 4.9, but with the new Arachne engine that will probably be included in version 5.0

@stevenm1954 3 года назад

This question is unrelated to the video but thought someone here might know the answer. My ender 3 max has been working great but when I try to print any new or existing projects it will not go to center of bed it wants to print in the home corner. I am not sure if clicked on wrong button or reset something I shouldn't have. Any suggestions would be great.

@FilamentFriday 3 года назад

Did you set the dimensions of the bed in the machine profile of your slicer to match the Max bed?

@stevenm1954 3 года назад

@@FilamentFriday I figured it out I somehow clicked on origin of center in my printer profile. I unchecked it and now it works. New at this 3d printing stuff so still learning but thanks for the reply.

@ToastbackWhale 3 года назад

"It automatically goes into line type" What has yours been going into? Mine has done that for a long time now...

@JelleSpijker 3 года назад

The default was material. But it remembers the last one you visited. It is really more to help us developers. wlwe got a bit tired of asking to switch to line type, when someone reported or asked something. A lot of new user's didn't know you could switch and often shared screenshot that were a bit harder to comprehend, because you didn't see the type of lines.

@davidjohnson8474 3 года назад

I hope you can help....Im getting an ender 3 max and wondering what would be a good laptop? I have a Chromebook but dont know if it will work or should I get a another laptop? Im a HP person

@The_printer_guy 3 года назад

how much $$ You have to spend?

@davidjohnson8474 3 года назад

@@The_printer_guy $500

@The_printer_guy 3 года назад

@@davidjohnson8474 it would be hard to get something good in this kind of money, if you want only to slice the files i would look for dell laptops with quadro graphics + 8/16 GB of RAM and i5/i7 procesors but the used ones

@bortasha 3 года назад

Since my upgrade to Cura 4.9.1 I have not been able to print anything - nada, zilch, nothing! I have leveled the bed very many times, even bringing the nozzle closer than I usually do. Nothing will stick! Cleaned print bed, used glue. Nothing will stick. It seems that the nozzle is to far above the bed on the first layer. I checked Z offset = 0. Any recommendations or settings I should check? Very frustrating because I was printing fine before.

@bortasha 3 года назад

After further investigation, my problem doesn't seem related to Cura. Just a coincidence that it started at the same time as the new Cura download. Can't print my old files either. It is a mystery to me.

@tristanmarquez1 2 года назад

Were you ever able to find what happened I'm having that same issue.

@FilamentFriday 2 года назад

Are you using a filament that has absorbed too much moisture? Try another filament.

@Spyderman500 3 года назад

Hey Chuck, have you heard anything about Ultimaker making Cura a subscription slicer? I guess Jurgen Von Hollen made this comment during a press conference a few months back.

@remcoburema7001 3 года назад

Can't say much more than 'don't worry' at the moment. Cura itself is going to remain open source, free, and usable without an account.

@eduardobarros6562 3 года назад

Is it just with me or people are also having a problem which is right at the start of the print, cura sets the temperature back to 0 for both extruder and heatbed. Also I dont have proof but I think it might be causing my printer to jam, the fillament melts up the heatbreak and solidifies there. I didnt have this after I started printing with the SD card and lubricated the fan. Idk if its related yet.

@mattlogue1300 3 года назад

God I wish you could change those colors. Red is terrible eye strain

@rainbow3d 3 года назад

Are you going to release new profiles for Cura 4.9? I lost mine changing versions....

@FilamentFriday 3 года назад

I might. Still working on it. 4.8 should load.

@rainbow3d 3 года назад

@@FilamentFriday I'll see if it does, I'll update later.

@rainbow3d 3 года назад

It seems to have no problems, the files imported just as usual.

@3D_Printing 3 года назад

Soon A.I. to do some donkey work I hope

@artineogda 2 года назад

Whether the project is no longer being developed?

@neillandscape1376 3 года назад

Installed 4.9.1 a while ago and now it decided it wont run, cx_Freezes:Python error message. Deleted all folders after uninstalling and still does the same after new install.

@volanel1129 3 года назад

Ciao e possibile sapere Setting for tpu??

@remcoburema7001 3 года назад

You'll have to change the material to TPU in the drop-down menu in the top middle of the screen in 'Prepare' mode. Once the material menu is open, go to 'Generic' and select TPU 95A, or something else applicable (if you know the brand for example). Materials for more specific brands can be downloaded from 'Marketplace' (the button in the top right corner, next to sign in ... you won't need to sign in. Menu may take a while to load. If it doesn't show up, check if it's the right diameter.).

@johnkemper1581 3 года назад

Thanks for the 4.9 beta review. I have installed 4.9 and have a question about the Color Scheme menu. My Color Scheme menu does not show the "Starts" option plus it has two other options which are "Only show top layer" and " Show 5 detailed layers". (These two options are also shown in 4.8) Also, a header at the top of the Color Scheme list says " Compatibility Mode" Anyone have any idea why my Color Scheme menu is different? And if possible, I would like to find out why I only have the vertical scroll bar when I am in the Preview screen. I have never had the horizonal animation bar in 4.8 and now in 4.9 I have researched some threads on this subject but have not had any success. I thought it was because I only had a cpu chip based GPU, but I recently Installed a Nvidia GPU but Cura still doesn't give me the animation option. (Note, I have set up the Nvidia software so Cura uses the Nvidia GPU.)

@FilamentFriday 3 года назад

Could be your graphics card is too old.

@johnkemper1581 3 года назад

@@FilamentFriday Maybe. My son gave me the graphics card. It is fairly old, but as far as performance its pretty powerful and has 4 GB of onboard memory. However, it might not support what ever function Cura needs. Do you know what video card is in you system?

@FilamentFriday 3 года назад

I use a Mac so not sure.

@johnkemper1581 3 года назад

@@FilamentFriday I found the setting that was forcing the "Compatibility Mode" I referenced above. Under "Preferences" / "General" there was a setting called "Force layer view compatibility mode" . On my installs of Cura, that line item was selected. I unselected that item in both my 4.8 and 4.9 installs and now I have the horizonal animation bar and all the "Line Type" menus are correct. Yea!

@DarylKLR650 3 года назад

Why does he have 2 extra selections on the left side of the Cura screen ?

@MechTechMax 3 года назад

Plugins. One of them might be custom supports, not sure on the other.

@FilamentFriday 3 года назад

I explain them in previous videos. Their plugins. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-owgUmQao2ME.html ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-D45eIhoWSyg.html

@DarylKLR650 3 года назад

@@FilamentFriday thanks man must have missed that vid

@MrBortxx 3 года назад

why the full layer at infill change?

@NLGeebee 3 года назад

Maybe to make sure that the new infill lines are supported?

@StumblingBumblingIdiot 3 года назад

When you select settings you can add the BOTTOM LAYERS option and set it to 0 and/or the TOP LAYERS also. Be careful that the lower or upper layers can support what you are doing though or it may fail, spectacularly ;)

@JelleSpijker 3 года назад

Per default the wall and skin are set to 0 for the modifier. CHEP removed these from the modifier, so it generated them as specified in the global settings.

@Paul_______ 3 года назад

More beard please

@dennisdecoene 3 года назад

Prusaslicer is always ahead.

@1QKGLH 3 года назад

I downloaded 4.9 and man do I ever have serious zits all over my prints. inner wall, outer wall. Everywhere. Nothing I do gets rid of them.

@greektechftw1174 3 года назад

Arachne means spider in Greek language

@shorb2289 3 года назад

Arachnid

@remcoburema7001 3 года назад

The naming scheme for Cura and libraries is moslty Greek/Roman mythology. Arachne is named after the myth, where a 'boastful' woman got turned into a spider by the godess of weaving (think it might be Athena) for daring to win(?) in a competition against her.

@robbinkoot2154 3 года назад

The thing with the block, that you change (in this case changing infill in a specific area), that's not new. It's more than a year old

@JelleSpijker 3 года назад

That functionality has atleast been present since 3.0 maybe even earlier

@FilamentFriday 3 года назад

I never said it was new. I said a lot people asked where it was in v4.8 so I showed them in 4.9 since it’s the same. Watch again. I also included a pop up link to my original details on the feature in my video from 2 yes ago: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-1nBnVtOEAiY.html