Hello I saved a washer motor like yours a number of years ago having a number of ideas of what I could do with it and so far all I have managed so far is to gather dust. As a person who has made and posted videos in the past thank you you have reminded me of some projects I would like to get back to and that I should get back to posting videos just in case I make one that someone would be encouraged by thanks again
Hi can I use this system to create a system to produce electricity at half of what its costing me at the moment @ $0.156 per kWh.Is this possible or not.Thanks
If you are based on academic knowledge, the result will be as you get. You have to look closely at Gerard's films once again, think about what Gerard has been working on for three years and whether you have actually reproduced his work. Listen carefully to what Gerard is saying with an open mind, try to find a similar Tesla work and then there is a chance that you will understand what it is all about.
Gerard mentioned that amps is your enemy and right about now he's not taking that fact into consideration. Lower the amps and a raised voltage should give you the torque via resonance frequency should do the job. Resonance and voltage is the key.
Gerard always said that these were to run on volts not amps. Printed on the side it certainly looks like it runs on volts and very little amps. From there he goes in another direction it seems. Didn't Gerard show where to purchase the controller?It seems everyone is trying to reinvent what Gerard already spent much time and money to figure out already.
Hi I want to use this Motor to drive a LOW 300RPM Wind Turbine Motor to generate electricity,do you think its a good idea.What issue would I come up against this setup.Thanks
Hi, there are such projects on the internet, some involving rewinding this motor, personally I did not build anything like that so I cannot say anything more really.
You mean Gerard? That's correct, and it looks like he found someone in China to do so, and he kept that secret - you can see on his videos that he kept the controller covered in piece of cloth. Now he is gone and unavailable and I did not find a single video where anybody went as far as I did with the controller. Thanks for your comment, you got me right.
@@krissio100 nd could pls tell which controller u can use to increase it to 1100rpm/380 vdc without having the controller that can b raised to 3600rpm or voltage 3phase vdc 1000volts as u suggest nd how abt the amps it consumes nd wt frequency do u get
@@DK-sg3oe I have used what can be seen in the video - NUCLEO-F446RE controller, STEVAL-IPM15B power stage and MCSDK-v5.Y.4 software. That needs to be properly configured and tuned to the given motor, which demands some knowledge and skill. I couldn't find any "off-the-shelf" solution.
All due respect but you still don't understand Gerard's concept he is using here. The problem is... You're still relying on Amps to drive it, conventional mainstream engineering, Gerard specifically states over and over his motors don't necessarily use amps to drive it, it uses "RF Frequencies" along with high voltage to drive it. This is a concept that hasn't yet been established in mainstream electrical engineering and science atm, only a few know about this, me included, for instance Eric Lewthwaite and of course Gerard and a few of the people close to him knows about this. From the looks of things, you're relying too much on artificial man made controllers to drive the motor, that's already the problem right there. Less is more here. A tip... Directly apply the electrical output from your source into a transformer voltage multiplier and then begin reconstructing Gerards concept from there to drive the washing machine motor. So the whole back emf problem you see is a symptom you're pushing speed with amps, which is what Gerard was criticizing.
Hi, you have a board under NUCLEO-F446RE, the one that connects to the STEVAL-IPM15B board? what is that? Can you please tell me where to get it? Regards Halvard
That's exactly that, controller (Nucleo) and power stage (Steval). You can get it on Farnell or smth similar. That's STMicroelectronics products, you'll find everything on their website.
DD stands for don't do, it's the worst motor/generator you will ever find, why? Because it's too accessible and it's designed that way, the only success one would have with one of these is by using it as a hidro electric generator on a river.
Wiesz co znaczy reguła Lenza ? Nie w zdaniu tylko czy wiesz co się dzieje ...... Jak prąd powstaje pszes generator to powstaje pierwsze pole magnetyczne W swojach Jak potem siła się doda to ona również pole magnetyczne robi które chamuje te pole w swojach Ale co by było jak by w swojach tego pola magnetycznego nie było ,jak by tak prąd powstał bez tego pola magnetycznego by tylko jedno pole magnetyczne zostało i te byś mógł wykorzystać. Pamiętaj symetrycznymi zwojami ci się to nie uda .
@@krissio100 I thought it had to do with back-EMF, unless a bearing is damaged it shouldn't consume that much energy as heat. But bearing choice could be just as valid. Cheers.