There are alternative points on the back of the motherboard you can solder to to make the top side look absolutely untouched. Did two falcons and they boot instantly.
Yea, fair point. I'll update the written guide with the DB1F1 alternate as an option for folks. For anyone interested in a kit that contains the resistor and diode you need you can get that here: weekendmodder.com/store/index.php?route=product/product&path=60&product_id=273
I've got a 256 jasper, will boot xell perfectly instaboot everytime Booting the dash glitches instantly also but also hangs at the end of the xbox logo animation, just after it signed into the profile I created to test the console. No hdd fitted I'm stuck
Thanks for making this man, I just killed my slim attempting the RGH 3 (that pll point is so tiny) but I still have an old falcon soI'm ready for round two! From what I've seen the points are a lot more reasonable, provided that I can scavenge a resistor and diode from somewhere.
Yah I won't mod a slim for rgh3 cause of that point. The phat consoles are easier for rgh3 but they are unstable still in beta. I did install on jasper it works great boots are fast. But ring of light is sometimes buggy
Welcome back doing Xbox stuff, how many parts and pieces from you back in the day I guess I need to buy some more parts I still have a few of these old ones laying around. Thanks again, Max
I actually just finished my second RGH for a jasper, broke the clk pad but learned how to repair the trace and got it working! Just ordered parts for a slim i picked up from your site to RGH 3
Thank you... booted Xell first try! Two weeks ago I spent at least 8 hours trying to RGH1.2 this same Falcon with no luck at all. I didn't think this was going to work because the original firmware RROD'd with the wiring installed, before I flashed the glitch 3 ECC... Wow, this is great. 20 minutes and success vs 8 hours and failing miserably! Oh, also I used 33K ohm resistor because I didn't have 22K.
I have done multiple rgh installs with no issues but one I installed recently the coolrunner chip was bad it RROD on both consoles and one won't turn on properly anymore get 0022 which is smc. I think chip had short in it which took out southbridge
Thank you so much for this!! Ended up having to resolder the RGH wires like 5 times (im kinda new to this) but at the end it booted into Xell! Again thank you.
And for removing all those screws I bought a little cheap $30 electric cordless drill more or less but it's tiny it weighs like 1 lb. Save so much time on the hundreds of councils I had to open and close. Back when you can make money and actually repairing these and reselling them. Did it out of my home during the recession and I was kind of fortunate that during the recession this kind of service was needed cuz I could make way more money than at any job available at the time even with a two year computer networking degree.
Thanks for your detailed tutorial. I did my first ever xbox 360 mod last night and it went smoothly. You're greatly appreciated. Did a Jasper my next attempt will be a slim
Thanks for a great tutorial. Just did the rgh3. 0 on a falcon 16mb and perfect. Instant boot everytime so far. I didn't have high expectations for the 3.0 but truthfully, it's turned out better than the rgh1. 2 jasper's in my possession, so pretty damn good. Thanks.
I am so lucky to have come across a xenon on blades dash, I did an JTAG using 3 wires, upgraded the heatsink and now the GPU rans cooler than the CPU, 55°C and 65°C respectively. I am still using 480p AV cable, i think thermals will go up when I upgrade to 1080i component AV. Thanks so much to weekend modder here.
Suggestion: love your videos. Can you do a tutorial on using the ext_clk method on a Xenon Xbox? Seems like most people these days have updated their dashboards and can’t use JTAG anymore… It’d be awesome as this is newer and apparently stable. And there is not that much info out there.
Awesome tutorial! Just picked up a really nice Jasper and a Falcon over the weekend that I will try my hand at the RGH3. Does the wattage matter on the 22k ohm resistor? I see 1/4, 1/2, and 1 watt values available.
Any advice on getting better boot times on BB jaspers. Seems even with a clean install they just aren't as reliable. May just stick to using matrix and coolrunner chios in all BB Japsers. More reliable.
Thank you a lot for your detailed videos, I always wanted to mod my xbox 360, bought some components but the methods and names of those were so confusing I never understood how to do it. Thanks a bunch for explaining it step by step
Forgot what the reason was for these being ~favored for modding and that was a handful of years ago.... Do those reason(s)/features still stand or have they possibly been muted or appended to with mod-developments among other versions of the 360s?
Custom dashboards, emulators, and mod menus in games are still fun to play with. Big driver recently is a game known as "college football revamped" which I think is a mod/update to a 2014 football game that a bunch of people are way into.
*love your vids !* I just JTAG'd my 360 Jasper and wondered if and how to install a 1TB 2.5 HD internal ? I believe the Xbox uses FAT32 , which has capacity limits :( Is there anyway to do it ?
If I understand you correctly what I did was plugged the hdd internally Then formatted it through xbox system then it started working I’ve heard that people have gotten 2tb working
Didn't know that was possible. What's the maximum size drive it can see? So the system sees and can manage among both at the same time? This total size capacity appears to be needed in my future.
@@That_Handle as far as I know, 2tb. Because you need to use FAT32 MBR formatting. You might be able to setup 2 partitions, but hadn’t tried that. I have tried 2 drives at once without a problem while in the Aurora custom dash.
@@Funkb0y , Where can I find that information for use in my planning where it comes to the file size required for a given game? I have quite a long list in front of me and looking to work smarter moreso than harder. No matter where I search I can't come up with file size basic information and it sure would be a lot easier to find rips than to have to wait out ripping my own from discs here = cut out that time consuming lengthy step for each and every disc that I have. What it comes down to is that I want to get my _entire_ library of discs onto mass storage as well as create multiple units for a LAN+online setup at home here.
Yeah it's called the Xbox removal tool how come you don't have one. I've had two for over 10 years and they work great. They're a bit flimsy they should be made out of stiffer steel because they've been pretty easily but you can pop all five of those and one shot
I’m trying to use this method to rgh3 my 360, after I soldered everything and tried to read nand it only fills in half the boxes in nand info. I managed to write ECC and boot into xell reloaded and get my cpu key but when trying to create XeBuild image lots of warnings pop up and jrunner crashes. I checked my soldering continuity and everything looks fine. Does anyone know what I could be doing wrong? Thanks
Great vid and tutorial, I would have ordered one of your RGH3 part kits, but I in UK.. So i order of amazon - The 22 Ohm resistor - does it need to be a 1/4 or 1/2 watt .. Many thanks
These eyes of mine are starting to strain nowadays.... Anyone recommend a magnifying video screen for my workbench? A TOMLOV with a pair of articulating lights and a remote came up in my results and looks decent except for it not having enough platform/stage depth for consoles; but, I know nothing.
A lot of those helping hands things he had also come with a magnifying glass, I'm farsighted so my glasses make it tough to see up close but the magnifying glass makes it easy if you're looking for a cheap option.
Great video.. here how to know if you got a good swicthing diode or a fake one test take one end to AAA positive side diode on the bottom of the AAA battery ohm reader ground ohm reader on the other side positive if your reading 0.201 or higher there will be some leakage current if so it's a good one.. if you are not then it's a fake online diode might matter on glitch boot ups worked on a Jasper BB
Hi pls help! I have a zephyr one and when I want to create Xebuild it always says Wrong CPU Key :Getting info from 192.168....... LockDownValue is 32 Wrong CPU Key
Can you make a video on zephyr xbox360 rgh2 new timmings by octal450 aka josh davidson?? Because i have one that i cannot do because no detailed videos tutorial of guide to do it bymyself
Great video my friend thank you I've completed this rgh 3 on several trinity boads but have not tried it on a falcon or jasper I've got a few jasper boards but can't seem to read the nand would like to save them
Hello. Which one of them should the 1n4148 diode be used? There are several types of diodes that differ in characteristics. There are diodes with different mA numbers. What characteristics should there be?
Hello weekend modder I did a Jasper RGH 3.0 few months ago but I only used a 22k resistor. I noticed you used a diode also is it really important to use one?
It's a protection to current backflow, you run risk of damaging your console without it. Rgh3 hasnt been around long enough to really know what the long term likely good of that damage is without it. But the diode is like a 5 cent part. Worth it to me...
Hi, great video.Yesterday I've done an RGH 3 on a trinity but I've confused inverting spi nand blue point with green point because I didn't look well schematics first. I've notice this after writing ecc. So I have a bad nand backup. Of course console after writing retail nand gives me red light and black screen. Could you help me? Only solution is donor nand? Thanks in advance.
Good morning, I went to do a solder at the tp7r3 point in the second solder but it ended up being damaged ... I wanted to know if there is another point to replace this tp7r3 point ??? thanks !! please inform me.
im having a hard time trying to solder to nand x or jr programmer wires to read the nands. Is there anything you can help me with to improve my soldering skills?
Flashed xell to two 360s now , all following your video step for step , none of them boot to xell after flashing it across , any idea what to do other than throw them in the bin was done with pico flasher and your jrunner and extras
@ TheWeekendModder Great video I need help I install everything and I create the ECC and Write it to the console but now the console won't boot the only thing is the green light flashes and nothing else what I can do please help
Quick question but if I Rgh my friends xbox that’s Flashed would It still be able to play backup games or would i have to re flash the dvd drive after thx ?
Hey, I just got done modding a jasper BB 512mb and everything works well except when I go into storage devices I do not see my internal memory anymore. It just shows the loading circle.(I've waited for awhile for it to show up) It never comes up. However when I put a HD or USB HD it will show up just fine (Will show the HD/USB HD and internal memory) Do you have any idea how to fix this? or has this ever happened to you? I just did 2 Jasper BB 512mb and they both have the same problem
Hi can you use the raspberry pico to flash nand of Corona 16mb no need for post fix adapter. I've seen another video where you rgh V3.0 without the need of a glitch chip. Could I do this using the raspberry pico, for this installation. Regards Andy
Just tried this on a BB jasper. Would not boot to xell. Checked soldering and stuff multiple times but no go. Windows 10 a problem? I read nand twice no problem and wrote ECC.
@@FreshLabs401 I'm using bottom point I finally got it to turn on but no xell do I need to reflash? It sounds like it quietly cycling fan motors but nothing happens black screen. I used a 10k as 22k wasn't working doing same thing after resolder points no longer shuts off instantly
I've got a 256 jasper, will boot xell perfectly instaboot everytime Booting the dash glitches instantly also but also hangs at the end of the xbox logo animation, just after it signed into the profile I created to test the console. No hdd fitted I'm stuck
Good day Mr weekend modder I have a trinity slim my dashboard is 17511 I did the rgh 3 mod on my console it boots xell very fast but it's not booting dash board for nothing I tried many stuff I even downloaded your j runner with the 17511 kernel version but tha does not have the rgh3 function I paste the 17511 into the jrunner with extras tried it git the kernel to show up did the rgh3 on the xbox360 only booting xell not dashboard really need your help please
I have a RGH 360 that has stopped glitching. Is there a market to sell these? Like would anyone have any interest in buying it? I have no use for it anymore. I only used it to download games to try before I bought them. I have since owned a One S, One X, and now a Series X. I’m well past the 360s lifespan so I literally have no use for it.
hello I would like to know what are the wattages that I have to choose for the different resistors for the RGH 3.0. should I take the smaller ones or the larger ones
Did exactly the same procedure, but when I turn it on power button, the xbox 360 automatically turns off after 10 seconds. Do you have any ideas what it could be ???
Mi jasper quedó con arranques variados ,7-15-25-30 segundos, y a veces se queda en el logo de inicio de xbox 360 y de ahí no pasa.. que puedo hacer para solucionarlo? Saludos
Hello everbody , i wanted to ask U for help. Ive Done the create ECC and write ECC before i even connected the diode and reaistors to my Falcon. Can i continoue normaly and Connect the reaistors and everything and create the ECC the Second time ? Or have i bricked my console allready? Thank U for the Help and sorry for my Bad english!
Can u use the same wiring for the glitch chip on a xenon i have matrix v3 with crystal so will i have to desolder that and do the bridge on the glitcher
Can you do a tutorial on a existing falcon or jasper console has already a rgh2 and convert it into rgh3, for those who has no copy of the original nand backup copy
@@TheWeekendModder thank you for the tutorial, uts just the same when you pdaye the dashbaoars to the latest, uts just you hav eto apply another step and check the rgh 2 then rgh3 on the right side.. tnx again sir
Thanks for tutorial sir, I just RGH 3 my jasper 16mb successfully but it's freezing after a few minutes of gameplay. Can you help with a method of solving these issues?
question before I buy anything can I mod online and use mods? can I use mods for achievements? and can I get banned if I use mods or mod for achievements?
@@TheWeekendModder ok thank you for answering my questions also would you know the chance of being ban? And where could I buy this stealth service I've heard about it before but not sure where to buy it because I haven't done this yet
@@steezykane4738 the chance is a variable based on what you do. Personally the risk is high enough I would never use an account I cared about for modding. Sorry I don't keep up with stealth server details these days.
Weekend modder, I did this same exact install on two big block Jasper Kronos, one works and glitches great but the other straight up turns off after 2 seconds! I re wrote the nand, checked the wiring and even re-did it but it keeps doing the same, at one point it booted normally for a couple of days but then went back to it. Can't find any solution! Any ideas? I can't get my hands on a jprogrammer or nandx so I'm just hoping eventually some pico support for writing chips is available as it seems my only option is to do a 1.2 install :(
@@XENON2028 where do you think could be? I checked literally everywhere and re did all the wiring yet the pattern for booting and not booting was completely random, without even moving it or touching it sometimes it will boot and sometimes would no
@@timoarrg hmm, if it boots sometimes its not a short.. i'm not sure whats happening, if you have discord I recommend joining the xbox 360 hub server and asking someone like octal450