No video :(

How to RGH3 a Xbox 360 Phat (Falcon/Jasper) - Chipless RGH 3.0 Tutorial!

MrMario2011

Подписаться 227 тыс.

Просмотров 66 тыс.

50% 1

Hardmodding methods for the Xbox 360 come back once again with one of the coolest implementations I've seen to date in the form of RGH 3.0 from 15432! While previous RGH methods required a glitch chip, different timing files, playing around with different wire routing methods, RGH3 eliminates a lot of that by completely omitting the need for a glitch chip! Why use a glitch chip when we can use the console to glitch itself?! Aside from the NAND wiring, the only other installation in the console is simplified down to two wires and a resistor. That's it!
This video will walk through the process of discussing RGH3, discussing prerequisites, and stepping through a full Xbox 360 Phat disassembly to get RGH3 installed. The installation itself will cover preparing the resistor, diode, wiring everything up to the console, and building ourselves a custom NAND for some homebrew goodness.
#RGH3 #Xbox360 #Xbox360Modding
This video has been made with Fair Use in mind and has been created as an educational piece of media.
--------------------
Timestamps!
0:00 - A Warning for Phat Consoles!
2:57 - What is RGH3?
5:15 - Motherboard Compatibility
7:04 - NAND Programmer Options
11:19 - Soldering Prerequisites
15:40 - Hardware Prerequisites
20:37 - Console Disassembly
28:41 - X-Clamp & Thermal Paste Removal
38:49 - Wire & Resistor Prep
42:17 - Preparing Points
43:57 - Soldering RGH3 Wires
45:49 - RGH3 Wire Cleanup
46:35 - Soldering NAND Wires
48:01 - Partially Rebuilding the Console
49:08 - J-Runner with Extras Setup
50:35 - xFlasher 360 Programmer Setup
51:10 - PicoFlasher Programmer Setup
52:51 - Building a RGH3 NAND
1:00:01 - Making a NAND Backup
1:02:01 - Teardown/Outro
--------------------
Product Affiliate Links:
Xbox 360 Console:
Amazon - geni.us/6T16Nnd
eBay - ebay.us/4aan93
Xbox 360 Hard Drive:
AliExpress - s.click.aliexpress.com/e/_9vJZ89
Amazon - geni.us/Xbox360HDD
eBay - ebay.us/hm0jO6
Raspberry Pi Pico:
AliExpress - s.click.aliexpress.com/e/_A0bqZv
Amazon - geni.us/XUS5Szr
eBay - ebay.us/V6fH6n
22K Ohm Resistor:
AliExpress - s.click.aliexpress.com/e/_Dkv...
Amazon - geni.us/EsY7k
eBay - ebay.us/1bufXU
1N4148 Switching Diode:
AliExpress - s.click.aliexpress.com/e/_Dn3...
Amazon - geni.us/XQJT2
eBay - ebay.us/p5IoWG
30 AWG Kynar Wire:
AliExpress - s.click.aliexpress.com/e/_AtyWUN
Amazon - geni.us/DXP0j
eBay - ebay.us/z1VaZF
Heatshrink Tubing:
AliExpress - s.click.aliexpress.com/e/_AmQjzV
Amazon - geni.us/ATn3
eBay - ebay.us/jHNsho
T8/T10 Screwdrivers:
AliExpress - s.click.aliexpress.com/e/_AVAmv1
Amazon - geni.us/yzIe5Vn
eBay - ebay.us/zwb5fy
X-Clamp Removal Tool:
AliExpress - s.click.aliexpress.com/e/_A5Mx3I
Amazon - geni.us/NhM4i
eBay - ebay.us/5Qfha8
Xbox 360 Opening Tool:
AliExpress - s.click.aliexpress.com/e/_Dky...
Amazon - geni.us/Kqdr
eBay - ebay.us/tjf1tZ
Arctic MX-4 Thermal Paste:
Amazon - geni.us/KwqeHy
eBay - ebay.us/VPcPrf
ArctiClean Thermal Paste Remover:
Amazon - geni.us/jMAOD
eBay - ebay.us/9qm6oH
Soldering Tools & Products:
US - www.amazon.com/shop/mrmario2011
UK - www.amazon.co.uk/shop/mrmario...
--------------------
Downloads & Links!
Octal's Console Shop with J-Runner Download:
octalsconsoleshop.com/
RGH3 Written Guide:
xbox360hub.com/guides/rgh-3-g...
xFlasher 360:
themodshop.co/shop/xflasher
PicoFlasher:
github.com/X360Tools/PicoFlasher
How to RGH 1.2 a Xbox 360 Phat (Falcon/Jasper):
• How to RGH 1.2 a Xbox ...
Aurora, Dashlaunch, and XeXMenu Setup:
• Setting Up Aurora Dash...
--------------------
Social Media & More!
Discord: Discord.Me/MrMario2011
Patreon: / mrmario2011
Second Channel: / ipsychozoa
Twitter: / mrmario2011
Facebook: / mrmario2011
Instagram: / mrmario2011
Twitch: / mrmario2011
--------------------
Song Information
Artist: pyama
Song: i was bored.
Soundcloud: literalbagoftrash
Link: / literalbagoftrash
--------------------
Any links specifically listed as affiliate links give me a small monetary kickback at no extra cost to you and no influence on the content.

Опубликовано:

6 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 377

@sj-red Год назад

Just ordered a Jasper. Watched your whole video; I only have minor experience soldering in school years ago but I think I may give this a go. I’m pretty hands on. Great tutorial; love how in depth your tutorial was while not being patronising. Will be sure to update you on how it goes when I eventually get all the kit together ❤

@MrMario2011 Год назад

Good luck! Along with that: practice, practice, practice.

@varona1590 8 месяцев назад

Did it work for you? where did you buy the RGH kit?

@gigalo21 2 месяца назад

last year i rgh3.0'D a trinity its super easy with no experience, but can be difficult linking wires to resistors and ground points hope your setup went well,

@Bidziilla Год назад

I don't know how often you get this, but I've watched your videos since about 2014. We've actually talked briefly before, funny enough. Still after all these years, you make good stuff for people to watch. Always very informative and make it very user friendly. You've always been very kind to me, and I love to see you still thriving today. Keep going strong, my friend. :))

@MrMario2011 Год назад

Thanks for hanging out!

@markusfpv1349 Год назад

You are the person that inspired me to do RGH on xboxes, I did couple of Trinity consoles using your guide and RGH 3 couple of Falcons. I do feel proud of myself that I was able to do it before you did the tutorial, but I am still very grateful for your work. Btw for removing old thermal paste I found naphta (lighter fluid) to be the best, it dissolves it in no time. Just remember to flush it with some isopropyl alcohol as naphta stinks a bit. Thanks again for your work man, cheers!

@JooshMaGoosh Год назад

@@repairstudio4940what's the right reddit community? I have two old (both working, minus one disc drive) phats and just got a soldering kit. I'm finally ready to dive in, just need this nand writer

@engrire8458 6 месяцев назад

Tried doing rgh 1.2 but I just couldn't get it to boot consistently if at all no matter what I did. So I tried this instead and so far it's been amazing, instant boots on my jasper 16mb. Really appreciate all your videos man they have made this whole process a breeze.

@alonsoknet Год назад

The explanation a the begginning of the video is perfect, cant agree more-

@art0van0derlay Год назад

Mr Mario - you are freaking awesome! I could never have done this without your expert guide

@MrMario2011 Год назад

That was all you!

@itz_Raed Год назад

Thank you very much. Great to see Quality tutorials in 2022.

@MrMario2011 Год назад

Glad it can help!

@ahna1795 Год назад

one of the best YT Guides ive ever seen. well done

@MrMario2011 Год назад

Glad it helped!

@ReevyMotovlogs Год назад

Successfully done 2 trinity's and 1 jasper with your tutorials now, thank you!

@MrMario2011 Год назад

You're welcome!

@renesav 3 месяца назад

Is the rgh 3 still in beta or its better now on falcom board?

@gianfypal8048 Год назад

I messed up One Jasper for the First Time. But thank you i did It on another Jasper and a Falcon and It perfectly works

@Normal_Andy 2 месяца назад

Aah here we go, thanks for another tutorial. Youre an absolute legend mate.

@dripeedrop Год назад

Thank you Mr. Mario for the heads-up. A big shut-out to the "Hellooooo..." Man Octo.

@MrMario2011 Год назад

HEELLLOOOOOOoooo...

@PhilThrahuile Год назад

I've done few 360 elite (jasper V2) rgh3 and yes, these have a bit inconsistent boot time (from instant boot to few sec, sometimes more than 10sec.) Sometimes, they won't glitch at all, but it's really rare, and you just have to turn it off and turn it on again. However, all of my 360 are at my friend's home, they are running at least once a week, and they never let us down ! I understand what you said, but with my small experience, I still recommend rgh3 on phat system if you want to enjoy good games for the cheapest price ! Keep it up !

@MrMario2011 Год назад

Sounds like a good experience, which is great! Although it can differ, you'll also see others who have a small experience and sample set who have had nothing but issues with their RGH 3.0 consoles.

@PhilThrahuile Год назад

@@MrMario2011 I agree with you, I actually read the comments ! Just want to share my (small) experience ☺️ On the first rgh I've done (jasper V2) ,I noticed that boot times are the most inconsistent, and I think it's related to the fact that I did put too long wires. On the phat consoles that I did rgh3 more recently, I put the shortest possible wire, and it did improve boot times, or at least the consistency. (Instant boot 30% of the time, and less than 10sec boot 65% of the time. Still got more than 10sec boot once a while, but it's not a big deal) I still use my first rgh frequently (my main system), with too long wires, and it still works very well !

@NSHG 11 месяцев назад

@@PhilThrahuile FWIW the only times I've had iffy RGH3 operation was on a 2008 Falcon that had two bad blocks of which one was in the 1xx region (the other was located at 2BD). Apparently it's a bit sensitive if it's the 0x1xx region when it comes to bad blocks...it did fix itself over time of usage, so probably just NAND rot?

@mrspy4264 4 месяца назад

Right now i just successfully booted my rgh3 falcon, thanks a lot for this guide!

@MrMario2011 4 месяца назад

Nice work!

@dasmikko Год назад

Great video! I've done the rgh3 on my 512mb jasper, with great success. Has been running for over a month now, with mostly instaboot times. I have been super lucky with my console. Fantastic instructions as always!

@modbox9560 Год назад

Does it have extended GPU heatsink or stock xenon 512mb??? Also it's a gamble long term you might end up getting zero continuity on stock resistors, caps, or diodes in area on phats later down road you may not only time will tell... like @MrMario2011 shared.

@dasmikko Год назад

@@modbox9560 i believe the stock xenon one. But yeah, only time will tell. Worst case is that i will have to covert it to a 1.2 rgh

@modbox9560 Год назад

@@dasmikko true true I mean m$ didn't design the supply's to be fabricated that way a glitch to glitch itself all in one who's knows what long term resistances are or gate drains on pwm parts have effects

@exodus_cl 7 дней назад

Went from 2+ minutes (or never) to boot (RGH2 Cool Runner C) to less than 10 seconds, Jasper console. Thanks for the video!

@MrMario2011 7 дней назад

You're welcome! Although the move there would have been better going from RGH2 to RGH 1.2

@exodus_cl 7 дней назад

yeah, but then I would have to program the coolrunner right? that makes it more complex (for me) because I would have to import a programmer board.

@NSHG Год назад

Huge props to your guide, now I'm a proud owner of both a Kronos RGH3 Elite unit and a custom-cobbled-together MS serviced Falcon that's RGH3'd. Kronos was done locally, the Falcon I did it myself. Bought a Pico, worked straight out of the first try with 27MHz. Shell is made out of a Elite Falcon that had a missing faceplate, and a scrapped (broke traces when removing X-Clamps >.

@MrMario2011 Год назад

Congrats! Awesome to see! The Falcon I showed in here is on 27MHz, works well but it takes 7 seconds to boot. No biggie, just 2 seconds longer than an instaboot.

@NSHG Год назад

@@MrMario2011 I did mine on 27 too. I suspect the Kronos (which isn't my work, it was done before I got hold of a USB-C RPi Pico to use as a flasher) was done on 10 MHz, which MIGHT be spotty? It sometimes sits at a black screen, though I just power cycle it whenever that happens and it boots up right away. Also check this out, I ran DashLaunch to set up Aurora as default boot dash and the console info is just funny - board indeed shows up as Falcon, yet the flash identifies itself as Trinity 🤣👍 How does that even happen?

@NSHG Год назад

And we have another winner! An April 2009 datecode 16MB Jasper successfully RGH3'd. Same 27MHz setting. This one must've been a shell swap of a modded elite (or at the very least the HDD was from a modded unit) as upon RGH-ing I was instantly greeted with Freestyle instead of the standard 360 dash, for whatever reason :D Off to Aurora it'll go since it's pretty void as is.

@gamehulk 3 месяца назад

Here's a tip for remembering the orientation of the diode inside your shrinkwrapped wire. Just use another color of wire on that end. I used a white wire on the anode side and a black wire on the cathode side. Easy peasy to remember which end to hook up to POST1/FT6U7.

@MrMario2011 3 месяца назад

For sure, I thought of it afterwards for the sake of that tutorial but didn't do so in the moment as I usually just stick to one color.

@amak1131 Год назад

Love the tutorial, but I always giggle at some of the blacked out info. None of it is really identifying or useful to outside parties.

@Maces006 Год назад

Followed this guide to install the the RGH3 after I had some issues with the RGH1.2 installation on my Falcon Xbox 360 (RROD 0010 error and then no HDMI output after fixing it). The only slight difference i have on my installation is rather than using a single 22K ohms resister, I am using 2x 10K ohms resisters in series (didn't have a 22K at the time). So far my console has been booting consistantly for the past week since its installation and hopefully stays like this.

@C0rr023 7 месяцев назад

Nice job and easy to follow. 👍

@MrMario2011 7 месяцев назад

Glad it was helpful!

@OrdinarySimonTheJoe 11 месяцев назад

It's most likely my goofy soldering but when I turn on the console it shuts off after a second. I'll retry my soldering tomorrow, I need some new heads because mine are starting to not even take solder.

@Luis08.10 Год назад

Great Tutorial. So I wanted to do it with one Xbox 360 Jasper but someone was there before me and the board was do messed up that the first one was a fail. The second Xbox I bought was a 360 elite Jasper. I used the Pico Flasher and faced the Problem that it would read the nand but they would not be the same,wrong header or it would automatically select RGH 2 even though it was a stock console. For those who have similar problems and soldered everything perfectly, in my case the cables which I bought were the Problem. After I change every kabel to a thicker one it started working. And so I have now a RGH 3 Xbox. In my case 10mhz works better than 27. Thank you for your step by step guide which was very helpful.

@MrMario2011 Год назад

Glad it helped!

@Luis08.10 Год назад

@@MrMario2011 it would be great if you could make a tutorial on how to flash the Xbox 360 with the custom latch that allows up to 16tb HDD over usb .

@psgodson4424 2 месяца назад

Awesome guide works 💯 thanks bro 😎

@MrMario2011 2 месяца назад

No problem 👍

@markray3263 6 месяцев назад

First, I like to thank you for creating these great videos, they are well done and thorough. They provide a invaluable resource to the mod (and maintenance) community. My only question is with the rear case sticker which shows 12v 12.1A, and the all black U2C1(Southbridge) chip, which I had always thought was found on Jasper boards. Was this a Falcon or a Jasper?

@MrMario2011 6 месяцев назад

I never look at the label, only look at the power plug for Phat consoles.

@LHPALADIN65 4 месяца назад

Another Great video !!! wish my soldering was better would love to try this.

@MrMario2011 4 месяца назад

Practice!

@DEMENTO01 Год назад

Just in time! i have a falcon a pi pico and the 22 ohm resistor all i need is for the 1n4148 to arrive probably monday. thanks !

@MrMario2011 Год назад

See you in a couple days!

@markrobertson2301 Год назад

I followed this guide extensively (Watched maybe 6-8 times) and so thought I would give my experience. I first tried to RGH 3 a Ebay Jasper 16mb elite, but it was too unreliable. The RGH would be working for one moment, then after turning the console off it would not, or only glitch once every 20+ tries. I re-made and re-soldered the wires probably up to 10+ times before the Xbox stopped working (During boot it gives me 1 solid green light and no video). I think the issues were due to the dodgy Xbox I received from Ebay. The external case was in pretty poor condition, the internals showed signs of liquid damage and had been opened before. One oddity I noticed while troubleshooting the RGH to try and make it reliable was that it would RROD if I brushed or touched the heatsink by a fraction - usually a sign of static electricity causing issues but I made sure I was grounded so not sure what it was. I then tried it on a Jasper 512mb from a local pawn store. It still had the warranty sticker sealed. After opening - it looked like it was never used - I could only find a very small amount of dust on the fan and that was it. With this Xbox I was successful with achieving a reliable RGH. At first it wouldn't work, until I tried 10Mhz instead of 27Mhz and it has booted successfully ever since (Boot times range from instant to 30 seconds). I have now transplanted the Jasper 512mb in my Halo 3 edition Xbox and I am a happy man. I think having an Xbox that was in much better condition got me over the line. Thank-you for the detailed video. I learned how to solder from this project. I look forward to doing more mods in the future. 👍👍👍

@MrMario2011 Год назад

Glad this helped! Thanks for sharing your experience.

@Mailmansson Год назад

You are definitely correct about Rgh3 fat boots times. Just had a jasper I had to refund the buyer. 27mhz would boot 50-200seconds or nothing. 10mhz just turned off on boot.

@Mailmansson Год назад

@@oOignignoktOo1 I have done like 25 fat consoles but this 16mb nand jasper didn't want anything to do with rgh3

@NSHG 11 месяцев назад

@@Mailmansson Did you have any bad blocks in the NAND? I nearly had that encounter with a Falcon that had NAND rot due to sitting unused. Cycling it a few times fixed it aside from a single bad block that was really a goner.

@Willy-tt6ez Месяц назад

Everything seems to have worked and I can boot into Xell with the eject button, but I don't have the glitch.ecc file to backup (every other file is there)? I'm assuming it's fine, but curious if this is the same for anyone else? Edit: I checked the logs and apparantly the glitch.ecc wrote to the nand successfully. Whatever, as long as it works!

@gamingwolf7895 10 месяцев назад

I tried to solder the wire to ft2p21 smc_post1 and the pad fell iff is their anyway that i can solder to another pad

@bpfifa08 Год назад

Thank you, I successfully RGHed my jasper

@MrMario2011 Год назад

Have fun!

@bpfifa08 Год назад

@@MrMario2011 thank you, love the well explained tutorials, looking forward for more!

@gamingwolf7895 Год назад

Does it have good boot times am thinking of rgh my jasper to with the pick

@androxilogin Год назад

These were the first consoles I had done this mod with and I was ecstatic. And then the problems began. My biggest problem was that it would never glitch on most boots. I'd leave it sit about 30 seconds before powering off then powering back on repeatedly until it started. I keep these in my closet for the time being. EDIT: Also want to mention, I use lighter fluid for thermal paste. It works wonders. drench piece of a paper towel, set it there about 10 seconds then start wiping. Of course follow up with a bit of alcohol to remove the greasy oil residue.

@MrMario2011 Год назад

Yep, RGH 3.0 for Phats is not stable, so you might have run ins like that.

@androxilogin Год назад

@@MrMario2011 Trinities are definitely my favorite revision. I've been hoping to see someone do a Corona with the latest version of my 3d printed post fix adapter. Every time I get a new console I set up the camera and tear it all down to find it doesn't require one. Before I would get one every other day! Ah, well. Nice presentation here, as usual. All explanation and low filler. This is the way.

@MrMario2011 Год назад

If it helps at all, that POST point under the XCGPU can be used in any Trinity or Corona console. Some people have to use the adapter if they screw up their POST point on the bottom of the board.

@androxilogin Год назад

@@MrMario2011 hey, that's a thought for testing purposes. It's easy to overlook the logical sometimes. I luckily haven't messed up any post points in all of my adventures. I have done two consoles with variations of the design I guess I failed to mention, but by that time I just wanted to rush to button things up left with only the idea afterwards. And why waste the thermal paste was the attitude by that point. I'll keep that in mind!

@sunny6630 Год назад

Don't use a diode just the wire it might work.

@masterchef2408 Год назад

Nice, Thank You

@anon_5513 Год назад

Just got a falcon for free, cant wait to use this soon!

@MrMario2011 Год назад

Perfect candidate!

@NAMEDTODIE Год назад

great video! I've done a few and had so many problems so i gave up, one worked perfectly then just wouldn't boot :( first didn't work with the diode at all, it only worked without the diode which i found strange, im not sure maybe it was my fault but obviously its certainly not fully stable, great tutorial and disclaimer non the less

@MrMario2011 Год назад

Yep! Thanks for sharing your experiences, that's why the disclaimer is there and RGH 1.2 is recommended on Phat.

@glazedd132 Год назад

I tried doing RGH3 to my Jasper, but it didn't work greatly, my console froze multiple times during boot and Dashboard. Anyways, nice walkthrough trough this mod :)

@MrMario2011 Год назад

RGH 1.2 is worth trying then!

@critical_confusion 11 месяцев назад

Hey man i'm planning on modding my jasper has rgh 3 been working good on your's as ive heard it is very glitchy

@akannigames809 Год назад

Anytime I try to RGH3 Xbox360, After Creating ECC then try to ON the xbox, it we not boot but I later discovered once it happened like that it means the Xbox as automatically as issue of three Red Ring of Death. So I want to ask if there is anything you think am doing in the process of RGH3, that is not Proper ????

@xai38-809 Год назад

Prob screwed up a component on the bottom

@Sergei-King 7 месяцев назад

Mannnn I miss the old 2010 JTAG days before RGH. Especially on MW2 with the infected quarantine patch! Crazy to think infected was created by modders & then adapted by Activision!

@ggnore8661 11 месяцев назад

Great video 👍 I’m having a little issue. Installed j runner w extras and installed the drivers for the xflasher as well but when I open jrunner while having xflasher plugged in and set to spi mode it doesn’t show up in jrunner.

@MrMario2011 11 месяцев назад

Use another cable or USB port.

@MaLilBunny 10 месяцев назад

Yea he needs a cable for data tran... there are cables that are only for charging

@flight79 Год назад

Thank you you helped me did as you said and it worked😀

@MrMario2011 Год назад

Glad it helped!

@Ryzobyte 26 дней назад

Does it matter if I use 30 awg kynar wire? Or can I use anything different?

@MrMario2011 26 дней назад

Up to you

@DJ96r Год назад

why the resistance soldered in different points from the other tutorial diagrams? Is there a difference in the final result ? thanks

@MrMario2011 Год назад

Recommendation from the developers, most likely because that's the value that provided the highest success rate.

@xai38-809 Год назад

Attempting on an opus nand read wiring the resistor and diode as we speak still mad about my "falcon" being a zephyr

@tayooo1000 17 дней назад

if any one has issues not booting or long load times use a 10k Ohm Resistor mine would not boot with the 22K Ohm Resistor

@Kara0626 Год назад

can I use a arduino as a nand programmer alternative? if yes can you make a video about that or tell me how?

@MrMario2011 Год назад

That's all you if you're going to port code over!

@notneb82 10 месяцев назад

Just ran the "Read Nand" on a Jasper and the program asked me what size Nand to dump. It gave me a choice of 64mb (system) and 512mb. I selected the 64mb option, should I redump the Nand using the 512 option instead or does it matter?

@MrMario2011 10 месяцев назад

I pick the specific NAND option.

@ndtemple417 Год назад

Did you make your nand wires or did you buy them? Those seem like it would make it easier.

@MrMario2011 Год назад

My PicoFlasher just has some 28 or 26 awg wires soldered in. For the xFlasher360 I took the standard NAND wires years ago, cut off the tips, soldered sewing needles to them, then used heatshrink tubing.

@peskandritsa2 4 месяца назад

best RGH tutorial out there

@MrMario2011 4 месяца назад

Thanks!

@kiellmorphet262 Год назад

I use the X clamp tool to take apart the whole console

@ahna1795 Год назад

Hi mario. I have one 512 jasper. Read and compare nands are ok. But when i write xell image, it beeps but the message "writing xell image completed" or something wont show up and it only says writing xell image and it stucks. If i turn on my console with eject button, it turns off after about 2 sec. No red lights. Just green light and turns off

@MrBlingBlingNr1 Год назад

Had the same issue also with a 512 jasper. glitch doesnt work, the fan is acting strange, like pulsating or so. I desolderd the wires, rewrote the stock NAND, but then the console shuts down after 1-2 seconds like yours did. So i rewrote again the stock nand and this time it worked. Tried it again, now its working.

@abbasmdim8907 Год назад

I need help! I just got RGH 3 then i got bad e68 and i remove a hdd then without hdd just power on but it wont boot up!

@MrMario2011 Год назад

If this happened after RGH 3.0 was installed, it could be an issue with your install itself, or your console isn't compatible with RGH 3.0 and needs to be changed to 1.2

@alvarograocosta5681 5 месяцев назад

The modification made to the bottom of the board that you made using a diode and resistor I have already seen done using a 1.2 volt voltage regulator. What would be the difference between the two methods and which would be the best option?

@MrMario2011 5 месяцев назад

The best option would be what is shown in this video, since that's what the developers of RGH3 intended and put in their documentation.

@alvarograocosta5681 5 месяцев назад

thank you friend . I will follow your advice. congratulations on the great work

@thereborne5219 Год назад

so ive been trying for a month now. i have a dump of my xbox. but then after that the xbox wouldnt boot and now it will not connect to my jr. it says console not found. what do i do?

@MrMario2011 Год назад

It sounds like you damaged something if it isn't booting up at all or being detected.

@thereborne5219 Год назад

@@MrMario2011 it boots because i re injected the dump i had. but now it just says console not found. so i can still use it. but cant connect it to jr.

@Japanese_dosent_work_as_handle Год назад

If you get a cheap soldering iron that comes with solder and no flux it will be almost impossible to solder anything to the Xbox without breaking it make sure you have flux or the solder your using has flux in it

@MrMario2011 Год назад

Wise words.

@Japanese_dosent_work_as_handle Год назад

@@MrMario2011 broke my old 360 slim a couple years ago because of this

@CrabHead501 Год назад

Question, if you already flashed your nand with RGH2 and you remove the rgh 2, and install rgh3 do you need to flash the nand still?

@MrMario2011 Год назад

Yeah. NAND had to be rebuilt to RGH3, then you have to desolder the glitch chip and solder in RGH3 wiring.

@CrabHead501 Год назад

@@MrMario2011 thanks for the answer!

@idontlikewhenpeoplearemean 9 месяцев назад

After reading the nand and doing create and write xell i got an error and my pico isn’t showing up on my computer anymore

@MrMario2011 9 месяцев назад

Sounds like a bad Pico?

@user-vq9kg5fl4n Год назад

what to do if after flashing the firmware I have 3 red lights and the fan noise is strong

@MrMario2011 Год назад

Try 10 MHz as well. Also make sure your soldering quality is good, wire routing is short, etc. If you remove the wiring and stock NAND boots, then it might be a case of your console not accepting RGH3. At that point RGH 1.2 would be recommended.

@thomasdupre572 Год назад

Hi ! Tried to RGH my flacon but no luck... Won't boot into xell, the console immediatly shuts down after spinning the fans for half a second... Wiring is ok on the second try, did I fry my console ? When I put back the retail it flashes 3 red lights... Maybe the diode and resistor must be removed before ? If someone could give me a hint I'd appreciate... (sorry if bad english)

@MrMario2011 Год назад

You cannot boot retail NAND with RGH3 wiring installed.

@sgcs Год назад

I wish I knew how to solder, I'd love to do this hack but it seems so difficult for a beginner like me (only done soft hacks up to this point).

@MrMario2011 Год назад

I was like you until I learned how to solder, which also involved a lot of failure at the beginning. Practice makes perfect!

@hmello3250 Год назад

why do xell gets stuck when the ethernet cable is plugged in?

@MrMario2011 Год назад

Couldn't tell you why, although if that's happening might be best to launch XeLL without being connected to a network and enter the CPU key manually.

@asmodeuso6 Год назад

would a rectifier diode work? I have only 1n4007 ones :( I harvested a diode from an old pcb that seems to be a switching one, but it's pretty old and I don't know if it's reliable and a 20k resistor would be enough?

@MrMario2011 Год назад

I would only recommend what I recommended in this video.

@asmodeuso6 Год назад

@@MrMario2011 ok, thanks!

@dropshop9393 Год назад

my friend what kind of tin you use for soldering is great

@MrMario2011 Год назад

I put my soldering products that I use in my Amazon shop, linked in the description! You should see the solder and flux I'm using there 🙂

@Armadyz Год назад

Hey man, I had a question. I'm not sure if this is stupid or silly but what if you want to remove RGH from your Xbox? Do you have a video on that by chance?

@Armadyz Год назад

Basically get the system back in stock format so you could use Xbox live safely

@MrMario2011 Год назад

Flash stock NAND and undo RGH3 wiring.

@gasj2 7 месяцев назад

Thank you!

@MrMario2011 7 месяцев назад

You're welcome!

@vaggelis2188 Год назад

Hello i follow all the steps right from the beginning and when try to boot after the creation of XLL the xbox open with a solid green light but no signal from hdmi What i can do? I working with raspberry pico on a falcon xbox and the same thing is doing with both ways 27hz/10hz

@MrMario2011 Год назад

Try both MHz versions. Aside from that, could be an issue of solder quality, wire routing, or the console just not accepting RGH3

@MrBlingBlingNr1 Год назад

Had the same issue with my Falcon. Today i´ve read a comment here that someone used a 10k resitor instead of the 22k. I tried this also and it worked. After finishing the RGH i put back the 22k resitor just to look if it´s stopped working, but it´s working fine?! Don´t know exactly why, but you can try that too.

@ryker86 Год назад

This might be a dumb question, but what is the main benefit of RGH 3 over RGH 1.2?

@MrMario2011 Год назад

No glitch chip.

@ZenonSmurfy0 2 месяца назад

All my soldering is fine and ok I’ve write ecc and not booting I have a 512 mb jasper is there something else I need to do ?

@MrMario2011 2 месяца назад

Soldering issue or your console won't play well with RGH3

@nickreip1402 2 месяца назад

I just attempted this and was able to write the nand but immediately after writing the nand I unplugged everything, desoldered the xflasher connector tried booting up again and got rrod or 3 flashing red lights, the eject boot to xcell doesn't work either but it did right before the nand write, not too sure if I messed something up, or if a nand corruption could cause rrod or if it's just a coincidence. Any help would be greatly appreciated, would love to know for sure if the nand can have no affect, I can attempt a reflow of the gpu if needed.

@nickreip1402 2 месяца назад

Error code is 0020

@MrMario2011 2 месяца назад

You won't know until you undo RGH3 wiring and write stock back.

@garkillack-7265 11 дней назад

hey man! It’s been over a year now since making this, how’s the console holding up and can you now recommend doing this? Or would you suggest anything different? Looking to do this to my Jasper v2 360 elite!

@MrMario2011 11 дней назад

My recommendations at the beginning are the exact same.

@Tech-NO-City Год назад

I found that if you dont have a TV on it wont boot its looking for a HDMI signal. That might be why people think it dont work at random.

@MrMario2011 Год назад

Correct, that's how the console works.

@MahmoudYahyaoui Год назад

Great video as always

@MrMario2011 Год назад

RGH3 can do that, unfortunately, as explained in the intro. Your console sounds like it needs RGH 1.2

@MahmoudYahyaoui Год назад

@@MrMario2011 yeah , I want to double check haha Thank you so much for responding 😘😘

@ABDO19608 3 месяца назад

Ihave problem wen i turn on console is not booting but wen I remove hdd is booting fast what i do 😢

@MrMario2011 3 месяца назад

Issue with your HDD.

@nunoinarak Год назад

I did it step by step but my console jasper 246 MB does boot in the XELL to get CPU Key . Could you please suggest me to bring it work fine? I check the soldering , It were correct and now I clicked read nand again so I lost the originon nand. thank you.

@MrMario2011 Год назад

Clean up wire routing, soldering, or change the MHz selected. If none of those are working, rewatch what I said at the very beginning of the video.

@nunoinarak Год назад

@@MrMario2011 Now I do not have the original NAND so I can not restore my jasper console . Now I have a Pico Pi .Can I buy only the cool runner to do RGH 1.2 . Thank you.

@WATP2000 Год назад

lol now im scared my RGH3 Jasper from ebay will stop glitching, had it for 4 months & it only takes like 5-10 seconds to boot 99% of the time. guess i'd better learn the art of soldering

@MrMario2011 Год назад

All you can do is hope it will continue to work, but it can't be guaranteed due to the nature of RGH 3.0 for phat.

@Goodgamer78 18 дней назад

Sick guide. Is it normal for glitching to take 6 seconds? It’s damn near instant to xell but takes 6 seconds to start the splash on retail. Is that just the nature of RGH 3 on Phat systems? Thanks

@Goodgamer78 18 дней назад

Should I switch over to 10MHZ?

@MrMario2011 18 дней назад

Totally stock retail takes 5 seconds, so an additional second is nothing to worry about. The Falcon used in this video takes 7 seconds to boot.

@Goodgamer78 18 дней назад

@@MrMario2011great, thanks! Never seen someone so active and willing to help in their comments.

@rxsebush6682 4 месяца назад

i've tried 2 jaspers and the rol just flashes on both i've redone the rgh wires and the nand wires but i'm still just getting the flashing light. any ideas or tips?

@MrMario2011 4 месяца назад

Remember the intro?

@rxsebush6682 4 месяца назад

@@MrMario2011 thanks for replying, I removed the diode and resistor on both consoles and they work, funny thing is I did this on a falcon and used the diode and resistor and it works fine

@shooter556002 Год назад

Boot time with RGH3 on Falcon/Jasper may need some luck. It can not be guranteed each boot is instant.

@MrMario2011 Год назад

Booting isn't guaranteed at all, noted in the beginning 😛

@muratrisvan Год назад

Thanx master ♥️🇹🇷

@AB-vt6dh 4 месяца назад

I have t4148 diodes, as far as I understand it is the same as 1n4148.

@RickTV0324 7 месяцев назад

My jasper didn't boot . After I write xell . It only yellow light on power button . But no display . How can I fix ?

@RickTV0324 7 месяцев назад

I'm using 1/4 watts 22k resistor

@MrMario2011 7 месяцев назад

Remember my warning at the beginning?

@tapoutms5608 Год назад

@MrMario2011 I got a problem after creating the ECC and writhing the console the only thing the happens is the green light keeps flashing and won't boot can you help and I try both the 27MHz and the 10MHz

@MrMario2011 Год назад

Could be soldering quality. If not, your console might not be able to take RGH 3.0, so RGH 1.2 is recommended.

@tapoutms5608 Год назад

@@MrMario2011 so how I can restore it back take out the ecc the I write on it and go back to retail and try that

@BlackDragon951 Год назад

What's weird for me is that the power socket looks like a falcon, but the power supply is 203W and the description above the socket in the picture is the same as zephyr. So do I have zephyr or falcon?

@MrMario2011 Год назад

Look super closely, best case you could have gotten a case-swapped system, worst case a previous owner did that nasty mod where you knock off the middle pin to make it work with a 175w power supply.

@BlackDragon951 Год назад

@MrMario2011 I just remembered that the power supply might be from a older 360 I previously had (it got 1 red ring and the e74 error code just after warranty expired) and I think that's where the power supply is from. This Xbox in the power socket it dose say FL which might mean it's a falcon maybe? But above on the case it lists the power specs of a zephyr. The console is manufactured in oktober 2007. The previous owner is my brother who left it when moved out and maybe because it had the disc tray won't come out (he had this same problem with another Xbox 360 he had and Microsoft replaced it and that one got the same issue afterwards as well)problem. Sorry for the wall of text.

@NSHG Год назад

@@BlackDragon951 The easiest way to tell is check for the MS sticker behind the faceplate. If it was tampered, your brother might have swapped a Falcon inside the Zephyr case. If not and the sticker is intact, you might have a M$ refurb.

@netheritecraftondrugs5126 6 месяцев назад

would rgh3 work on a falcon from 2011? what about a falcon from 2009? im curious because i used to have a falcon from 2009 and it was my dad's but now i have one from 2011

@MrMario2011 6 месяцев назад

Yes

@knowyoshiz7525 Год назад

What is rgh build

@AB-vt6dh 4 месяца назад

Hello. Jasper 512mb. J-Runner offers me to read 64 or 512 nand, which one should I take? Thank you.

@AB-vt6dh 4 месяца назад

Thanks, I solved it. No matter which, both match.

@MrMario2011 3 месяца назад

512

@marcos-y9p Месяц назад

hello everyone, new guy here. i looked up the availability of resistors on amazon and have a couple of questions. which ones are better for the rgh3; 1/4, 1/2W or 1W? ...also does the direction of the resistor matter for the color stripes? thnx

@MrMario2011 Месяц назад

None of those matter for the resistor, what's important is resistance.

@marcos-y9p Месяц назад

@@MrMario2011Heh, as the replies go that is pretty definitive and thanx for the quick reply. i`ve been loosing sleep over your tutorials. can`t wait to get started on the og xbox and the 360.

@swolepp 5 месяцев назад

does anyone have a schematic for the traces leading from the rgh connections on a jasper 16 mb. i need to see if i have a broken trace. I installed xell with j runner and my pico flasher never connected again so i installed a nand flash from usb and now all i have is a black screen.

@MrMario2011 5 месяцев назад

Doesn't sound related to NAND traces.

@swolepp 5 месяцев назад

After I used Jrunner to read the nand it said my dumps matched so i installed Xel. I ran Xell and got my cpu key but when i went to write the patched nand it said no nand in source so i went into my dump folder and realixed that one of the dumps was entirely empty. I then decided to let it rip and patched what i thought was a good nand dump and installed it. I dont think there is any helping this console now.If there isnt any helping me at least maybe someone can learn from my mistake and be sure to verify their nand dump. I can nolonger connect to the nand with jrunner. I guess the only option is to put an entirely different nand on the board which i dont have the tools for.@o2011

@pastedtomato Год назад

I found on a Spanish speaking forum, a method where they completely ditch the transistor and resistor and use 2 AMS1117 1.2v voltage regulators, supposedly, it's safer and more stable on Fat systems

@MrMario2011 Год назад

Not needed or recommended, I've spoken to Octal about this at least twice who is one of the people who worked on RGH 3.0

@gamingwolf7895 Год назад

I want to rgh for cheep is it good if I do this on a jasper or no go

@gamingwolf7895 Год назад

I only got like $16

@MrMario2011 Год назад

I wouldn't recommend attempting any hardmod if you're that low on funds, especially since you'll need more on hand in case you break your console.

@gamingwolf7895 Год назад

@@MrMario2011 I have the soldering gun, flux , solder. Sorry for bugging you but can I use electric tape instead of the heat shrink stuff

@gamingwolf7895 Год назад

Also if I break it I ain't really losing anything cuz I got a free jasper

@user-cr4kh6iy5g Год назад

Mr mario i have an xbox 360 with bad nand with out a back up and i dont no what to do can you help me

@MrMario2011 Год назад

Hope you've got the CPU key for it.

@user-cr4kh6iy5g Год назад

@@MrMario2011 no i dont have it

@milanterzic3980 Год назад

If someone's falcon doesn't want to boot after installing xell, let them install a 10k resistor... mine didn't want to boot with a 22k resistor and with 10k it was insta boot

@MrMario2011 Год назад

Each console is different! That can happen.

@ianhaylock7409 Год назад

I didn't have a 22K resistor, so I used 27K also insta boots.

@MrBlingBlingNr1 Год назад

Thanks for the tip. Mine didn´t work first time with the 22k. Tried a 10k instead and it worked! Just for curiosity i removed later the 10k and put back the 22k resitor. Working also fine now?! wierd!

@LukeAkAscooterkid Год назад

Can anyone help me find a guide (if possible) for a refurbished xenon board. I believe it had a different code name elpis. Recently picked one up.

@MrMario2011 Год назад

This guide works if it is an Opus.

@LukeAkAscooterkid Год назад

@@MrMario2011 mine is for sure a xenon, it has a 203w PSU. After a little more research its the GPU that's been changed to an elpis 80nm. Not sure if it can be modded at all? Anyone have any ideas.

@chrismcleod5876 4 месяца назад

Couldnt get xell to boot, fortunately i was able to write retail back

@MrMario2011 4 месяца назад

Great! Give RGH 1.2 a try

@georgeianos9631 10 месяцев назад

hello, I want to make my jasper v1 console in rgh 3 and I want to talk to you because I see that you installed rgh 3 on an xbox 360 phat and many of the xbox 360 fans told me that it is unstable and I want to say that the console it deserves rgh 3 per phat at 10hz or 27hz ?

@MrMario2011 10 месяцев назад

Covered in the video.

@georgeianos9631 10 месяцев назад

@@MrMario2011 I saw your video but I want to say is it worth rgh 3 on my phat console

@muharremaltintas Год назад

Hi, Is it posible jtag the 2007.07.10 manifactured Xbox 360?

@MrMario2011 Год назад

Only if the dashboard is 7371 or lower and isn't a patched CB.

@xai38-809 Год назад

idk if u will see this but my cpu is reseting but it wont ever boot into xell

@MrMario2011 Год назад

Could be soldering quality, wire routing, or your console won't work with RGH3

@xai38-809 Год назад

@@MrMario2011 I found out my mobo that mind you had the 14.2 amps was somehow a zephyr

@Mdodo18 Год назад

hey, do you think its possible to do this without flux ? I have everything I need but I have no flux, the welds are small i dont know if it possible or not(the PPL point scare me), I'm in a hurry to do it ... This video makes me want to bring back the old consolle just for that I thank you, have a nice day

@MrMario2011 Год назад

You have no flux and you're in a hurry? I wouldn't recommend you continue at all until both of those are remedied, or else you're going to leave a follow up comment asking how to fix damaged points.

@Mdodo18 Год назад

@@MrMario2011 hahaha no if i take the risk, it must be my fault, i happreciate your reply, and thank you very much for this vidéo !