Dialing In And Putting The Plasma Table To Work!! This Thing Is SWEET!!!!

Подписаться 253 тыс.

Просмотров 35 тыс.

50% 1

Prismatic Powders: www.prismaticpowders.com
Skat Blast Sand Blaster: amzn.to/3iDro9D
Evolution Chop Saw: store.evolutionpowertools.com...
Redline Powder Coating Gun: ebay.us/TqqvsZ
Crossfire Pro Table: www.langmuirsystems.com/pro
Primeweld Cut60: amzn.to/3GjZdEd
AHP Tig Welder: amzn.to/3GoOSXx
Motor Guard Filter: amzn.to/3H0SBMP
Where I buy parts:
amzn.to/3B7SKuw
ebay.us/wuVMNx
Sponsors/ Discounts:
Evolution Power Tools: "ANIEMELA" aspireiq.go2cloud.org/aff_c?of...
PerformanceTDI: "AUSTIN10" Saves 10% performancetdi.com
EcoFlow: amzn.to/3Uw0mO7
Atoto: amzn.to/3Y0Khms
www.prismaticpowders.com
www.cerakote.com
Check out my website! avrcustoms.com/
Follow me on Instagram! / austinniemela
Camera equipment used in the video!
Sony ZV-1 Camera: amzn.to/3N0SksQ
Rode Mic: amzn.to/3OnQUKw
GoPro: amzn.to/3ty94RJ
Tripod: amzn.to/2WjasJM
Send me stuff!
PO Box 133
Chattaroy WA 99003

Развлечения

Опубликовано:

11 янв 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 86

@conservativeokie Год назад

It was so freakin’ awesome seeing you integrate your other shop technologies into this process! You are a smart young man Austin! Great work! Keep it coming amigo!!! 😁👍🏼

@MG-sg2ci Год назад

For your pierce holes, you need to do lead in and outs on your cuts. That will allow a clean cut around the parts.

@alaskadroneshots1057 Год назад

also need to adjust rotation of your cuts Counterclockwise for inside cuts, clockwise for outside.

@built4xploration448 Год назад

Make your hinge points smaller (longer relief cuts). Then heat the hinges ant it will bend super easy. Been thinking about getting one of those tables for a while now. Thanks for sharing your experience with the learning process.

@albeenog2432 Год назад

Very cool stuff! Next project- cart or table for the evolution and get it up off the floor😊

@fasttimez9651 Год назад

you're an absolute joy to watch my friend. please keep the content coming !

@amcustomfab Год назад

Awesome to see you're rockin the prime weld pierce delay sometimes play a part in that cut quality as well thanks for the great content 😎

@austinniemela Год назад

Hey man I’ve watched a few of your videos! How would pierce delay affect the cut?

@amcustomfab Год назад

With Pierce delay you see the biggest difference in the holes. Pierce delay is basically the amount of time in between where the torch fires and then starts moving for the cut . If the pierce delay is too short and the arc does not penetrate the material fully before it starts moving. You often get a trailing arc that can contribute to the beveled cut. The thicker the material the longer your pierced delay needs to be. But just in fractions of a scent. Definitely not an expert but I'm happy to help to the best of my ability 😎 been running this table for about 2 years now .

@caracarametal Год назад

I really enjoyed this, so cool to see all the pieces come together

@Michael-Gould Год назад

Brilliant! I so want a plasma table now!

@Justforfun-ek7et Год назад

Pretty flipping sweet addition to shop!

@12345doughnuts Год назад

You are such a talented dude! Keep up the good work brother

@billocampo1365 Год назад

Can't wait to see your next project..

@ronthompson2366 Год назад

Very nice 👌 this will pay for itself almost immediately. As for a good "Break" ... take a look at Harbor Freight. Also keep an eye out....any of the local sheetmetal shops. Sometimes they are upgrading their equipment... various reasons.. but you can sometimes get a great deal on used equipment. Some of the supply companies in the area... for metal work and machinist and machinery repair. Have knowledge of used equipment. Your going to be putting on an addition to your shop before long... paint booth... fab section.. 👌 Growth is good 👍 Looking forward to seeing the truck additions and then the FJ.

@SootyDiesel81 Год назад

I’ve been building replacement plasma bed inserts for the past week 12 in total its 3x24 meters 2 cutting heads and cuts 2” hardox plate like butter

@neffwai Год назад

That's cool too watch n definitely I learned there is little bit entitled to plasma cutting table definitely u made yours more user friendly. Yup time for the fj40 can't wait bro

@korysteffen884 Год назад

Excellent spray can technique

@planeflyer21 Год назад

Thanks, Austin! Looking forward to seeing more of this plasma table. How big is your shop? It looks like a pretty ideal size.

@jamescole3152 Год назад

Someone was showing the sparks. They are suppose to go down at an angle. If they come up above the workpiece the feed rate is too high.

@RonaldCiubuc Год назад

Just rad! Insane!

@michaelwenman2348 11 месяцев назад

I don't have my plasma table yet or any experience with one, but with my cnc router, if my cuts are at a taper, then that means that the router bit is not sitting at 90 deg with respect to the table...it is tilted just a bit. Also if the holes are elongated or squares aren't square, then the stepper motors need adjusted / calibrated.

@twinpeaksco4101 Год назад

fun tip: metal paint scraper is the fastest easiest way to knock the dross off the back

@bikesandflite1126 Год назад

Love that channel, have you considered kicking the stove and building/buying a stand up oven 4x4x6. Its a game changer like that sweat plasma table will be. Just a thought.

@jasonw2696 4 месяца назад

🤣🤣❤️👍🏼 that’s exactly what I would’ve done too powder coated it😁❤

@OctoberGambit Год назад

I would freaking kill to have Austin build my ‘86 SR5.

@paulmartin3340 Год назад

Awesome video as usual ! I can see a lot of great custom pieces being cut out on that table... I'm not sure but when I've watched other guy's with their plasma cutters I'm sure the start their holes in the middle so it doesn't tail off into the piece. Anyway cheers and thanks for the entertainment. Sydney Australia MATE 🇭🇲👍🦘🇭🇲🇺🇸🇭🇲🦘👍🇭🇲

@elevatormechanic3486 Год назад

the first thing I would make is a laptop stand. lol

@pauldavis1890 Год назад

A really good air dryer will help with the dross. Also slowing down corners and radius’ to 1/2 speed will make holes way better. I you do lead ins and lead outs same thickness as the material you’re cutting you’ll have a uniform perimeter and better holes. Got my plasma 10 years ago I can send pics of cut quality off the table before cleaning if you’d like to see

@austinniemela Год назад

Thanks! I have been doing these things and its helping! I may still have some moisture in my air I need to address! How much dross are you getting? Some people say you will always have it but I have seen some very clean plasma cuts!

@pauldavis1890 Год назад

@@austinniemela a desiccant air dryer is the best low cost solution. I have 2 water catches, then desiccant air dryer, then debri catcher then it goes through to the plasma which has its own filter. When I change out the desiccant and cut 1/4” or 1/8” MS at 45amp I can take the part off the table and the top has nothing and the bottom has about 1/16 max dross that knocks off with a fingernail and absolutely no angle. Would still have angles on holes a little bit but I just oversized them 1/16”.

@austinniemela Год назад

@@pauldavis1890 I have a copper pipe cooler, water trap, desiccant, and a motor guard filter! I don’t know, some how I must still have moisture, all signs point to it!

@dustinwalden7091 Год назад

I like how a new plasma table isn’t that expensive but a new press brake is eighteen million dollars.

@Kelly-yo2yk 3 месяца назад

I really enjoyed your video! I would like to know what the primer stage of your powder coating process is about? Is that a primer or ???? Thanks ,Geoff

@johncourtneyscott2757 Год назад

Austin, that’s coming along great man. You have the gimmick going on

@norcoredneck Год назад

What powder coating gun are you using? Projects a looking great.

@backbeatwoodworks 2 месяца назад

Do you have the plans available for the Cut60 shelf?

@luistamez1141 Год назад

What you do before the electro estatic paint? Is that a sand blast or something?

@jimmyv2649 Год назад

I see a new blast cabinet. Did you give up on the Harbor Freight one?

@iconicrodcustom2159 Год назад

where did you get the longer cables?

@vettepicking Год назад

A nice 12 gauge 48" finger brake isnt cheap. Last i saw was 4k from tennsmith. But thats the only one i would buy because im always doing thicker metal bends.

@austinniemela Год назад

Yeah they aren’t cheap! I would want one that can bend 12-11 gauge for sure!

@alvarof.montes5531 Год назад

Great video, I have a question, why don´t u use a mechanized torch?

@austinniemela Год назад

I need to order one!

@BarHRanch Год назад

Maxed out that oven

@kieranmann9761 Год назад

Awesome project!! That plasma table will get a lot of use for sure. How about a stand or table for your saw? Better than working on the floor. Keep up the great videos!!

@user-fd6lt3iz6j 2 месяца назад

If you really wont thé best cut kwalitie out off your tabel you need a fixt noselholder. They so much more stable. But the down side is you Cant cut Manuel anymore.

@METALMUNCHERS77 8 месяцев назад

Taper that’s plasma for the holes especially on thicker materials

@daniellevandovsky3947 6 дней назад

What were you setting for cutting aluminum?

@MussaKZN Год назад

If you find another oven you could cut the joining sides out and have a wider oven.

@tayfka Год назад

Респект мужик👍💪

@Z-Bart Год назад

When dealing with 1 1/4" drain fittings...In a P-Trap kit there is a gasket (fat one) for 1 1/4" tube. You just use the normal 1 1/2" sink nut. Plumber pro tip.

@austinniemela Год назад

Wait.. so you can put a 1 1/2” p trap on a 1 1/4” pipe with just a gasket?! Good to know

@marknichols7861 Год назад

With taper… check online for better information - but, visualize the shape of the plasma arc looking from the side… it has a taper to it which will effect the taper of the cut. Higher cut height, taper wider at the top. Lower cut height, taper wider at the bottom. See if you can find a better explanation online regarding this as it may help.

@rogerthetinker5116 Год назад

use Oxalic acid mixed in the water to prevent rust

@philliprickman1394 7 месяцев назад

Nice mods. I don't understand why Langmuir doesn't change the drain design on the pans. It seems to be the first modification everyone makes to their table. I've been planning to do the same as you did on mine.

@SlapHappy Год назад

Plasma cutters simply have that beveled kerf, its because of the way the air swirls around in the tip. The only way to fix this is to get better torches and consumables. That is what sets the hypertherms apart from these cheap chinese cutters.

@bloggs4214 Год назад

What type powder coat gun is that your using?

@Quebecer_Powerstroke Год назад

Redline EZ50

@MSK-engineer Год назад

For that you sandblasting metal before painting???

@travismiller9213 Год назад

Yay! Bring on the FJ!

@michaelpolimer2128 Год назад

get rid of the hand torch and put a machine torch on so the cables don't pull the nozzle out of plumb, you would be surprised we were........also the table next to the wall is a mistake they cut but they are messy........ happy cutting 73 Mike K1FNX near Boston

@revtmyers1 Год назад

Nice mods

@d.collier_8280 Год назад

Woodward Fab finger break

@tradeMark182 Год назад

That green truck is a oh mama kinnda truck Austin

@tbranscom1 Год назад

I would sugest trying to run you cuts through one time without that toilet paper style filter on the line, they are really bad about restricting the amount of volume you can pass through an air hose at once especially a 3/8 hose with standard fittings. A Desiccant Air Cleaner would be a much better choice for your setup that will let more air move through it consistently.

@austinniemela Год назад

Makes sense! I am upgrading to all 1/2” lines and that may help!

@tbranscom1 Год назад

@@austinniemela that will certianly help, just remember when plumbing the airlines its only as good as the smallest restriction.

@conservativeokie Год назад

I completely understand why you did it this way, but would have loved to see you use Cerakote on these instead of Van Sickle. Just sayin’…. 😁

@FlawedOffroad Год назад

Check out Mike Festiva here on the tube, hes been running these tables for a few years and has some videos on settings and mods and whatnot

@torowazup1 Год назад

👍🏼👍🏼👍🏼👍🏼👍🏼👌🏼😎

@user-cl8bn9ew1t Год назад

🇮🇶♥️🌹

@user-ms1vy1hc4w Год назад

Доброго здоров'я привіт з Одеси Україна.

@darylbayes4574 Год назад

you sir need a wider press.

@austinniemela Год назад

Absolutely!!

@natelammers652 Год назад

FJ40 Time!

@grantpeckford8082 11 месяцев назад

Tip may be too big

@chalinp4886 Год назад

But can it cut a 🍕

@jasonw2696 4 месяца назад

You must not have a wife and kids🤔 because my wife and kids wouldn’t leave me alone long enough to do a damn thing out in the shop🤦🏻‍♂️

@austinniemela 4 месяца назад

Haha I have a wife and 2 kids! I just lock the door 😂

@ACE-gk5gi Год назад

Hey hey fucknnn hey LOL it's ya goofy m8te from Australia 😆 love ya show [ HOLDEN COMMODORE VE UTE HSV Maloo R8 E series LS3 turbo start up accelerate sound ] - mate type that in on utube watch n enjoy...it only goes for 1.56 sec but wait till you see it..on a big screen..[ let me know what you think about the car in a reply ] ya goofy m8te from Australia

@Hackjob-Extraordinaire Год назад

leave much less material between your bend cut lines, say 3/16in, and youll love how it bends.

@DieselRamcharger Год назад

cut max amperage all the time tune the feed speed till it cuts nice

@princenoah21 Год назад

Say, for future projects, you say sometimes when machine shops rebore your engine cylinders, they sometimes do it wrong. Have you thought about getting your own boring/lathe machine to rebore engine cylinders yourself? Or would that just be impractical?