Тёмный

Distributor Cap + rotor replacement Autozam AZ-1/Suzuki Cara, hauling stuff with my Nissan Atlas 100 

Anything Wheeled
Подписаться 1,9 тыс.
Просмотров 238
50% 1

Further continuing on the path of troubleshooting why Suzuki Cara Autozam AZ-1 is acting up hitting a phantom rev limiter.
I show you how to replace your distributor cap and rotor in this car then haul away some scrap metal junk I have, putting my Nissan Atlas to work.
Chapters:
0:00 Intro
0:31 Looking over the distributor cap and rotor to plan the swap
1:02 Philips head screwdriver to take the screws off cap
2:09 Rotor overview and removal
2:42 Indiana Jones crumbly artifacts
3:15 Comparing the caps
3:26 Reinstalling everything
3:49 Start and find out if that fixed it
4:24 Nissan Atlas 100 helping me stop hoarding junk at my house
5:04 How much metal I brought
5:44 How much money I got for the stuff
6:32 IKEA flatpack hauling and a super duper tall fridge.
#f6a #carmaintenance #autozam #az1 #autozamaz1 #suzukicara #suzuki #engine #maintenance #carrepair #howto #nissanatlas #truck #pickuptruck #scrapping #metalscrap #troubleshooting #carissues

Авто/Мото

Опубликовано:

 

2 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 6   
@dadeyeyam
@dadeyeyam 3 месяца назад
great video as always!
@Mightymatt54
@Mightymatt54 3 месяца назад
I did the plug/wires/cap/rotor on my az-1 over the winter, that strut bar is 90% of your difficulty here! It's perfectly aligned to be where there is otherwise a near-straight shot to get your arm into where the distributor hides. Your old parts didn't look too bad but it's good scheduled maintenance either way. Fun tidbit - since the rotor can go on in any of the three positions, you can put the plug wires "clocked" any which way (in the right order) as long as it lines up with the rotor (which could conflict with the numbers on the cap - which puts 1 at the top if I remember correctly, contrary to internet-info saying #1 is the forward post).
@AnythingWheeled
@AnythingWheeled 2 месяца назад
Now that's just making it confusing 😆 it's easier to just document how it came out and put it back the same way! Sometimes it's unnecessary but I'm paranoid
@CappuccinoDrives
@CappuccinoDrives 2 месяца назад
I give that job to the Cara. I hate how it's against the firewall in the Cappuccino
@AnythingWheeled
@AnythingWheeled 2 месяца назад
You just need a right angle Phillips head screw driver. Is the Cappuccino cap the same with the screws?
@CappuccinoDrives
@CappuccinoDrives 2 месяца назад
@@AnythingWheeled I can't remember, I haven't touched it since 2019, engine out. It might be coming, and I'm not looking forward to it.
Далее
Аминка ❤️
00:16
Просмотров 1,1 млн
Importing my Kei Van | Summer Project Series
5:00
Просмотров 3,6 тыс.
Motor Oil & Fuel Additives: Just a WASTE of MONEY?
27:33
Cylinder Offset Changes Everything
23:45
Просмотров 2,5 млн