Ditch light install with Baja Designs Pro S2 LEDs - Toyota Tacoma = demo in the end!

Подписаться 22 тыс.

Просмотров 43 тыс.

50% 1

I wanted more frontal lighting for offroad situations but I wanted something low key.
I found that that the Baja S2 Pros would fill my needs for being low profile and bright! 2400 lumens each! I needed the brackets and other hardware and saw that Rago Fabrication just changed their brackets to stainless steel so now there's no rusting issues.
Here's my vlog about it. It highlights the crucial steps I took to get it working.
Here are the links for the products I bought:
Baja Designs S2 Pro combo: amzn.to/2ZDdMyY
these below are actually better than the RAGO ones...
ditch light switch amzn.to/3ej4Nah
switch holder amzn.to/2ZEXJ3I
ditch mounts amzn.to/3d43s7c
other parts I used to install:
zip wire ties amzn.to/2GRnPaM
Add-a-fuse: amzn.to/2InOSrf
positaps: amzn.to/2IlUHWo
3/4 inch split loom tubing amzn.to/2IoRcya
1/4 inch split loom tubing amzn.to/2q0rold
solderless 'crimp' connectors amzn.to/3KemH1m
14 gauge wire amzn.to/2GuapCb
wire strippers amzn.to/2IqVkhf
racheting crimper amzn.to/2Gt1GjI
black electrical tape amzn.to/2q1jhUI
I opened a Patreon account to help me out with future mods to review as well as audio video equipment to buy for a better presentation to you all.
/ robdaman
items used to produce this video:
DJI Mavic Pro drone - amzn.to/2lAH0Jt
Polar Pro Filters DJI Mavic Filters amzn.to/2CpaO2V
Samsung Galaxy S8+ amzn.to/2wCFA4M
Zhiyun Smooth q mobile phone stabilizer amzn.to/2vuX5Ho
Samsung 64gb microsd amzn.to/2CuKxkf
Canon 5D Mark III amzn.to/2w92vpn
-----------------------------------------
Please check out my blog at robdaman.blogspot.com and instagram @_robdaman
______________
Disclaimer:
Due to factors beyond the control of Rob Daman, I cannot guarantee against improper use or unauthorized modifications of this information. I assume no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. I recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control , no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Rob Daman.
#tacoma #toyota #quicksand #robdaman #robdman #coopertires#stmaxx#volkracing#quicksand#trdbro#trdpro#tacoma#quicksand#truck#goexplore#getoutdoors#offroading#wheeling#overlanding#mallcrawler#trdoffroad#Tacomaworld#toyotatruck#toyotalove#toyotatacoma#bajadesignsofficial#TacomaBeast#TCMBST#te37x #raysmsc #sema2019

Авто/Мото

Опубликовано:

2 апр 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 143

@RobDaman 4 года назад

Here are the links for the products I bought: Baja Designs S2 Pro combo: amzn.to/2ZDdMyY these below are actually better than the RAGO ones... ditch light switch amzn.to/3ej4Nah switch holder amzn.to/2ZEXJ3I ditch mounts amzn.to/3d43s7c

@ffsteel111 4 года назад

The drone shot of the lights turning on was awesome I’m looking at getting a pair myself and that was definitely a great depiction of how they shine

@RobDaman 4 года назад

thanks. i did this 60 sec vid for some of the other lights.. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-3t8yp2bk5r8.html

@singletrackftw 6 лет назад

Smart man, I just did S2 sport ditch lights in Amber. These S2’s are great because they are SO low profile. So many people run ditch pods and they are massive and goofy looking but these S2’s are very sleek and powerful.

@RobDaman 6 лет назад

That's EXACTLY why I went with these! Great light output in a compact design. Low key. Thanks for commenting.

@EmpTy-kf2rq 6 лет назад

Yes, they are sleek. I saw this setup on a BD employee’s FJ. However, BD said for an extra $90 more you could get a pair of Squadron Pro for double the output.

@RobDaman 6 лет назад

You're correct but I didn't need that much throw for my goals. All of Baja products are awesome. If you want throw check out their instagram posts on the laser one.

@singletrackftw 6 лет назад

Rob Daman now that we’re talking about all of this, I’m finding that my s2 sports don’t throw enough light 😂. Went wheeling last night for the 3rd time with them and they are technically enough but not really enough light power for me.

@EmpTy-kf2rq 6 лет назад

singletrackftw upgrade to the Pros. 30 day money back guarantee.

@theasapsquad 4 года назад

Excellent content! Love your step by step guides it really helps out for us non-electric savvy people

@RobDaman 4 года назад

Themango17800 thanks for the feedback 🙏

@RobDaman 6 лет назад

Happy Taco Tuesday everybody! I hope you guys enjoy my latest install vlog. These tiny lights are impressive!

@marlonm396 6 лет назад

Rob, you are a jack of all trades. You know how to do everything :-) Truck is looking better and better as you add more stuff to it. Congrats!

@RobDaman 6 лет назад

Thanks! I Try and dabble in all aspects of DIY so I can save a few bucks for other mods. haha. I appreciate the compliments. I'll try not to disappoint.

@boxerdad214 6 лет назад

Best video Yet. Wow. I need these lights

@RobDaman 6 лет назад

They're awesome lights! low profile but killer output.

@ProjectOnix 5 лет назад

Life saver video! great tips and tricks!

@RobDaman 5 лет назад

real fancy

@michaelpotestio7261 4 года назад

Rob! Great video! Thanks for the suggestion for posi-tap connectors. Tapping a wire is so much easier with these.

@RobDaman 4 года назад

glad to help. I love post-taps

@tareskisloki8579 4 года назад

Very nice, though if it were me, I'd be turning them so they actually function as ditch lights, which would also take the glare off the hood.

@RobDaman 4 года назад

Thanks. They're turned more now. I noticed really turning them didn't help since the front is so tall. Having the front camera is a definite plus too

@DanielGonzalez-pn8gv 6 лет назад

Cool video. Like the ending.

@RobDaman 6 лет назад

Awesome! Thanks for watching it's entirety.

@abdullahal-shimri3091 2 года назад

Looking good! Mine are pointing outward.

@TacoParty 5 лет назад

Nice! This was helpful :-)

@RobDaman 5 лет назад

glad to help

@artbencomo317 6 лет назад

Sweet.

@junokim2907 6 лет назад

Great Vid! Quick question for ya. I know you did the Lastfit video for low beam led headlight before. However, in this video, is it still the same headlight or different one? Thank you!

@RobDaman 6 лет назад

thanks! these lows are rx350 retrofits with 35 watt ballast. The highs are actually Most Plus LEDs which was one of my early mods. When I flip the highs the rx350 flip too because it's bixenon so i have 4 bulbs lit up. :)

@fjrey648 5 лет назад

I just got my ditch light brackets from Rago Fabrication. Now shopping for some ditch lights. Not sure if I want to go with Baja Designs or another brand. Your vid was great and gave me some ideas for the FJ. Good job, brother!

@RobDaman 5 лет назад

Thanks for watching. There's several well built brands and it really depends on what your budget is and how much light performance you're looking for.

@eu7212 5 лет назад

Nice

@chasebasile8767 4 года назад

Did the s2's come with hardware to mount to ditch light brackets? You said it was a 15 mm top bolt, was that bolt and nut included?

@RobDaman 4 года назад

Yes. Nuts and bolts included 👍

@239-swfl5 6 лет назад

RD, a little off subject looking to replace low beams (bulbs only) with LED's that would complement my OEM fog LED's 'and DRL's on output lumens? To many options and looking for a long lasting quality bulb, any help would b appreciated.

@RobDaman 6 лет назад

Hi, Sounds like you want to get a similar color temperature around 5500-6000k to match. Lumens would be more for brightness. These 2 products are a good bang for the buck and I haven't heard any negatives. amzn.to/2ubUlxR amzn.to/2tTJnxl May the Fourth be With you

@chad0063 3 года назад

You said "It says to tap the green" of the cargo switch to have the switch lit up with headlights - where did you find what color wire to tap in another switch that said green? I am wiring a 4runner and tapped the green of my windshield wiper switch (which is lit up when headlights are on) and my switch is not lit with headlights. Thanks

@RobDaman 3 года назад

Could be different color wire in a T4r. I'd suggest testing your connection with a test light or multimeter. I had an issue with the LX light and it was cuz the tap didn't pierce properly.

@MarkMollat 5 лет назад

Do you have a picture or video showing the ditch light on at night? I want to know if there is reflection on the hood. Thx! Im thinking of using it as chase lights rather than ditch lights.

@RobDaman 5 лет назад

Ya there's reflection because of the flood. You can see it in the ending of the video night shot.

@MarkMollat 5 лет назад

@@RobDaman I was hoping for an inside the cab view... :)

@RobDaman 5 лет назад

Check my Joshua tree vid around 5 mins ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-YhKvBC6MXNQ.html

@christiancalma502 3 года назад

Where did you run the other red wire from the Baja design harness?

@RobDaman 3 года назад

Both red wires go to the switch

@saywhuuh 5 лет назад

Where in the firewall did run the wire? Where's the best place? Is it that little grommet next to the brake booster? thx!

@RobDaman 5 лет назад

I used the big grommet w the wire harness but you have to be careful since you're close to important wires. I'm going to use that grommet for a switchpro harness

@saywhuuh 5 лет назад

Thanks Rob. Update us on that too.

@mmunoz5875 4 года назад

Did you use Cali raise switch for your install?

@RobDaman 4 года назад

These were by rago

@SWFlowseeker 4 года назад

What is the difference from the ditch/driving combo? I’m not sure what on to buy Ty. Love your truck

@ReiCaixa 4 года назад

Don't we all love RU-vidrs that go through all the comment section to show that he care, but then doesn't even answer our questions like he doesn't even care?

@RobDaman 4 года назад

@@ReiCaixa Ya RU-vidrs suck. I noticed he did answer another question here in the same video from same person (copied and pasted for you since you apparently missed that). But I still think he doesn't care though. Maybe I'm wrong but I'm siding with you. SWFlowseeker 3 months ago Thx for the vid. Did you put in a relay or just use the inline fuse? 1 ▼ Rob Daman Rob Daman 3 months ago just a fuse as it's pretty low amperage. SWFlowseeker 3 months ago Rob Daman Ty. I was unsure

@SWFlowseeker 4 года назад

Thx for the vid. Did you put in a relay or just use the inline fuse?

@RobDaman 4 года назад

just a fuse as it's pretty low amperage.

@SWFlowseeker 4 года назад

Rob Daman Ty. I was unsure

@nickolaguez 4 года назад

Rob Daman wait so you're using the dome light circuit to power those ditch lights? No relay?

@mmunoz5875 4 года назад

What are your high and low beams, brand? I take they will both be H11's?

@RobDaman 4 года назад

this video my headlights are HID retrofits. D2S if I recall. highs are h11s. I used 2 brands mostplus being highs but lasfit is good too. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-98RpgQ9Nl3w.html

@mrbruns2619 4 года назад

Do you by chance know what gauge wire is used for the BD wiring?

@RobDaman 4 года назад

I'm guessing it was 14 gauge. amperage draw on this light is pretty low.

@cypher302 3 года назад

Great video, I bought S2 sport BD ditch lights my harness has 3 wires. Black and two reds....I know black is ground and one red is for relay but that extra red wire? Also using Cali raised OEM switches.... please help? Lol

@RobDaman 3 года назад

i never worked with cali raised but i'm going say 1 red points to the lights and 1 red points to 12 volt source. the switch will be what interrupts the voltage.

@00oFAVIANo00 5 лет назад

i had the same issue with the short Y split wire. Does the added wire have to be the same thickness? i added a slightly thicker wire that i had laying around and it did not work. any advise is appreciated!

@RobDaman 5 лет назад

Hi. Different gauge wire in that low amperage set up shouldn't be an issue since you mentioned slightly. What did you do to extend the wires? Crimp connect? You could always remove that wire and temporary twist the the wires to test. If you have a multi meter it would be better so you can test voltage. It also has a fuse and switch so check that too. Let me know how it goes

@00oFAVIANo00 5 лет назад

I connected the wires by twisting the. I checked everything before cutting the harness and it worked as it should. It only stopped working when i cut and added the extra wire. I did notice the wiring got really hot so I removed the extra wire and everything worked again. Might just purchase the longer harness from BD

@RobDaman 5 лет назад

sounds like that extra wire was causing a short for some reason. That heat was an indicator. Good thing you noticed it.

@l33america 4 года назад

how do you get your fog lights to turn on separately from headlights?

@RobDaman 4 года назад

My model has a OEM fog light switch on the stalk.

@MrOddxball 5 лет назад

Rob great video, well all your videos is helpful... question.. I currently have the same setup on my 2nd gen taco, but how did you do the wiring? I heard u just chop the switch portion, but did you keep the portion where it wired to the battery?? I also have an aftermarket switch from Rago that I want to use instead of the switch that came with the lights, thanks in advance

@RobDaman 5 лет назад

Thanks for watching. You would connect your Rago switch to either your fuse panel with a Add a fuse or your battery directly. Then from that switch you wire your lights. It's low enough amperage that you won't need a relay.

@MrOddxball 5 лет назад

@@RobDaman I suck when it comes down to this kinda stuck... I was trying to follow your steps but couldn't do it...😫

@RobDaman 5 лет назад

@@MrOddxball Just look at the switch diagram. 1 goes to the lights, 1 to the ground, 1 to illumination for your button, 1 goes to the fuse or battery to power your lights.

@MrOddxball 5 лет назад

@@RobDaman great thanks Rob!! Keep them videos coming

@MrOddxball 5 лет назад

@@RobDaman when you said one to the fuse or power, is that the one when you used the add a fuse for yours?

@dannyreyes5973 5 лет назад

Rob, I literally bought everything you suggested and will be attempting this tonight. How do you connect the ground from the harness to the ground of the switch to the pig end? Did you just throw a pig tail on the end of the ground switch from the harness and then just slice the ground from the switch onto it? Also, where did you attach the pigtail to the truck to ground it?

@RobDaman 5 лет назад

Hi I grounded at a bolt right by the fuse block and yes pigtailed the others together. Let me know how it goes

@dannyreyes5973 5 лет назад

Rob Daman To my relief everything worked the first time haha. Thanks for your step by step guide!

@RobDaman 5 лет назад

@@dannyreyes5973 cool! glad it worked out 👍

@BPxGarage 5 лет назад

Hey bud! Hoping to get your opinion on these. I have the CaliRaised side shooter pods which are a great flood light. I wanna find a small light like this to pair with it for a spot that throw light farther. What do you think of these? They look great!

@RobDaman 5 лет назад

Were you trying to link something?

@BPxGarage 5 лет назад

@@RobDaman No, I'm talking about the ones in this video...

@RobDaman 5 лет назад

ah. they're awesome lights. if you look at my Joshua Tree video you can see some of the throw on them.

@BPxGarage 5 лет назад

@@RobDaman ahhh sweeet!!! Yeah let me check that one out. Thanks Rob!!!

@Maxdaddy543 5 лет назад

The Rago’s are good but the Cali low profile are better suited for the S2s.

@tomlang9177 4 года назад

Do you know if they made the wiring longer??

@RobDaman 4 года назад

no. you'll have to make your own if need be.

@Meeks3 3 года назад

Roughly how much wire did you add? Awesome video BTW! I'm installing S2 sports.

@RobDaman 3 года назад

It's been a while. Maybe 6 feet. Probably less

@Meeks3 3 года назад

@@RobDaman so I just wired up my bajas and now the switch won't stop illuminating. Did I wire something wrong?

@RobDaman 3 года назад

Sounds like you're using a constant 12v source to the illum wire. Check with a multimeter to confirm.

@ashlen737 3 года назад

Is that a mini low profile add a fuse?

@RobDaman 3 года назад

yep amzn.to/2InOSrf

@tcma-4x490 6 лет назад

Damn, wish I bought the latest brackets from Rago, I had to cut up my cowl for the install.

@RobDaman 6 лет назад

Didn't know they revised the shape as well as the material.

@tcma-4x490 6 лет назад

Rob Daman I don’t think the material was changed. The new ones bolt onto the hood with the 2 bolts. The older ones use 3 bolts and a little more work to install. Cutting and trimming is required to the plastic right below the windshield. I’ve since changed my bulky led pods and now running kc flex lights, a little less brighter but way more sleek. I like the ones you’re running, nice vid!!

@anthonymaestas8876 6 лет назад

Damn how many sets of rims do you have?

@RobDaman 6 лет назад

I just have 1 set on the Taco. Now if you asked how many wheels have I had...? This is the 4th set not including stockers.

@rascoe2018R1 5 лет назад

So all you did was add red and black wires to the existing y splitter and still use the harness that came with it?

@RobDaman 5 лет назад

On one end yes then I chopped the switch and added my own dash switch.

@rascoe2018R1 5 лет назад

@@RobDaman awesome, thanks for the quick reply and your taco looks alot better with the retro making it unique 👌

@RobDaman 5 лет назад

Glad you like it

@michaelwongpydochc 5 лет назад

Ended up running mine through the hood

@RobDaman 5 лет назад

😎

@p-mac5969 3 года назад

Were you able to use the wiring or did you have to add wire? I could be wrong but I though if you cut the wires it void your warranty on the lights.

@vinhbui5491 5 лет назад

In the Baja Designs switch it has 4 wires 2 red , 1 black and 1 red black. How do you wire to the OEM switch?

@RobDaman 5 лет назад

OEM switch? I think you mean Baja Design's switch? 3:22 is the BD switch red wires are positive leads to power the lights. black and black/red are ground wires. it's been a while since I installed it but you can call Baja Designs direct and confirm.

@vinhbui5491 5 лет назад

I mean how you wire the switch that you replaced

@RobDaman 5 лет назад

@@vinhbui5491 its in this video which wires go to which

@vinhbui5491 5 лет назад

Could you tell me more about it? Rago Freedom switch has 4 wire 1 green , red 1 , red 2 and black. How you wire it? I just only know the green will be added fuse. How about the other. I really appreciate for your help sir.

@vinhbui5491 5 лет назад

I’m not sure but this is the way I’m thinking Rago Freedom has 4 wires Green will be added fuse Red 2 will wire to the dashboard wire Black will wire to the 2 black/wire in the Baja switch and then mount it underneath And Red 1 will connect to which red on the Baja switch (cause Baja switch has 2 red as well) and What did you do on the circuit from the battery to the light

@kylepeter6862 5 лет назад

U da man

@RobDaman 5 лет назад

Yas!!!

@arnulfonunez3102 4 года назад

What fog lights are you using

@RobDaman 4 года назад

baja designs squadrons. those are an older version. i now have SAE street legal ones. did a vid ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-b3K0bz1pUNQ.html

@EmpTy-kf2rq 6 лет назад

For the hood bolts, why not remote one bolt, install the bracket with 1 bolt and just rotate the bracket to the next hole, per instructions?

@RobDaman 6 лет назад

Good question. I tried it and it wouldn't clear. The curve of the hood wouldn't allow any clearance to do that. Even if I tried 1 hole and loosely attach a bolt there's no way I could remove the other bolt. I suspect the instructions are good for the 2nd gen and 4runners which there are videos to confirm that technique. Having another set of hands would have resolved needing to do it my way which I don't recommend.

@EmpTy-kf2rq 6 лет назад

Rob Daman makes sense. I have a 4th gen 4Runner. I just watched your video again and noticed that large bulge. Keep on modding! Great and simple videos, Rob.

@RobDaman 6 лет назад

Thanks for watching and the compliment.

@ashlen737 3 года назад

What gauge wire?

@RobDaman 3 года назад

14 I put specs and tools when I can in the video description 14 gauge wire amzn.to/2GuapCb zip wire ties amzn.to/2GRnPaM Add-a-fuse: amzn.to/2InOSrf positaps: amzn.to/2IlUHWo 3/4 inch split loom tubing amzn.to/2IoRcya 1/4 inch split loom tubing amzn.to/2q0rold solderless 'crimp' connectors amzn.to/2IqLZ91 wire strippers amzn.to/2IqVkhf racheting crimper amzn.to/2Gt1GjI black electrical tape amzn.to/2q1jhUI

@ashlen737 3 года назад

@@RobDaman my bad, i missed that but appreciate it! Have you had any issues since the video? Baja told me today I need to add a relay if using the Cali raised switch. But I don’t want to buy another harness or add a relay in if I don’t need to.

@isaactrujillo76 4 года назад

If they’re called ‘ditch lights.’ Why does no one point them at Ditch level?

@RobDaman 4 года назад

what's good is they're adjustable. I ended up doing just that when it as pitch black at Joshua Tree. Amazing output for a little package.

@isaactrujillo76 4 года назад

Rob Daman awesome! My runner game with baja style lights. I turned the outside lights towards the ditch. An the two in front of the grill straight and up a bit. It’s perfect for now.

@Maxdaddy543 5 лет назад

I love your channel! But you did it way wrong! One bolt at a time!

@RobDaman 5 лет назад

Hi, Unfortunately there's no way to do it one at a time like 2nd gen tacos or 4runners. The shape won't allow it.