DIY Glacier Bay Toilet Assembly and Installation 

Thank you for the details! Other sites skip steps as if they are obvious to anyone. Newbie here👍

Hey Andy, I followed your handy instructions, and my toilet worked Dandy. Thank you.

Well, I finally installed this toilet. And the only thing that didn't work was that the plastic caps covering the bolts would not click down into place. It appears that the bolts are too high and need to be cut down. Rather than disturb them and screw up something, I will probably just use some silicone to keep the caps in place. Also, with a 12-inch rough-in my tank was also touching the wall and the lid went on just fine.

Thanks for the video just saved $250 plus by doing it myself. That was very helpful n god bless u.

Thanks a lot!

Thank you! You are a lifesaver. My first toilet install. Thanks to you it will be done right. I liked, subscribed and hit the bell.

This video helped me tremendously. Thank you very much you did a great giving all instructions and information

3:55 What a tease! 😂

Thanks for the video!!! I dropped a sub! I forgot the gasket and had water everywhere lol

The black gasket is keeping my tank screws from being flush into the holes.

Thank you for identyfying the black part of the wax ring and showing what to do with it (which is discard it, btw, in case anyone else was confused about this part like me). Since mine was suck in my flange, I didn't know it was part of the wax ring scenario and was thinking it was a part of the flange and thus it should remain. After a way too long google search and just as I was about to give up and leave it in (which is wrong, btw) you told me otherwise. Merci Handy Dandy Andy :)

You made it look easy. Thank you

Thank very much for the details...it work for me awesome!!

First class instructions 👍🏾😎👊🏾

Anyone else have a hard time with the gasket on the tank to the bowl sitting flush? Mine has a gap on front and back. Not touching the wall. It’s like the gasket to to damn thick.

Thank you, great video just got the toilet gotta put it in today

Metal washer should be on top of the toilet next to plastic washer. According instruction inside next to wax ring nut goes without washer.

Thank you so much for this video!!

I did it! Thanks you so much!❤

Thanks, helped me out a lot

Thank you for a great video it helped a lot

I noticed that you only used hand pressure to seat the toilet and then attached the wing nuts. Won't it sink down further when someone heavy sits on it? Meaning, shouldn't you sit on it to seat it fully? Also, this was a really tight fit--the tank is touching the wall before you even put on the lid. I'd guess you actually have a 10" rough-in. Were you able to get the tank lid to fit properly?

Thank you!!!

Thanks!

I couldn't figure out how the toilet tank gasket went on and the stick figure drawing in the instructions wasn't much help. I put it on turned inside out and it leaked but your video showed me the error of my ways. Thanks!

It always happens when you're out of town!

There could’ve been discussion about whether you got the round toilet, or the elongated glacier bay toilet also was curious about the number of inches from the wall that each toilet requires for the distance from the wall.

Does wingnut and screw come with tolilet?

What is the black hose in the top of the tank for

My tank is wobbles back and forth any insight? Gasket is on right as well. Any thoughts?

Good video and as far as the toilet paper I like to put it the opposite way of people that get mad about it just to bother them I like to think it help get their crap 💩 out faster

Are all toilet Bowls have the same waste line specs..i.e. 4 Inch?

great video bro

How did you get all the residual water out of the toilet?

I forgot to put the red gasket from bowl to tank...and now I can't seem to remove the tank from the bowl to place it....help?!?!

Is the part on the bottom of the tank the flange or what?

Did you get the tank parts off of your old 🚽 toilet

The transition at 5:00 didn’t help. Not sure how/what you removed from the old toilet before putting in the new gasket

Easy to install, ru-vid.comUgkxjA-hDN2m8_mi0Dg0JD8U6QiArozIAc4I and comfortable. No idea what other people were talking about when they said it was difficult to install or uncomfortable.

With germs present, why did you not put on medical gloves?