DON'T DO THIS! 5 (MORE) Common Car Audio NOOB Mistakes!

Подписаться 780 тыс.

Просмотров 1,1 млн

50% 1

Whether you want earth shattering bass or high quality sound performance there are mistakes we need to avoid in car audio. Many of these same mistakes are made with speakers, subwoofers, amplifiers, wiring, and car audio installation. Here's five MORE mistakes to avoid!
▼ Tools and Materials:
Box Design Blueprints - goo.gl/isgdSC
Wire Grommets - amzn.to/2H47W0S
Step drill - amzn.to/2Ixu9S2
As an Amazon Associate I earn from qualifying purchases.
🔊 Want more? Check out these links:
✅Car Audio Tutorial Library: bit.ly/CAFlearn
✅ FREE weekly training program: bit.ly/CAFlist
✅ Box Designs, BUILD YOUR OWN BOX!: bit.ly/CAFdesigns
✅Join the CAF Patreon Member Team: bit.ly/CAFpatreon
🔊🔊🔊 FULL VIDEO SERIES PLAYLISTS:🔊🔊🔊
- Ported Downfiring Subwoofer Build: bit.ly/CAFdownfire
- Dad's Sound Quality Daily Driver Build: bit.ly/CAFdadsSQ
- SEMA F150 Subwoofer Box Build: bit.ly/CAFf150
- LOUD Wrangler Build - bit.ly/CAFloudwrangler
- SQ Grand Cherokee Build - bit.ly/CAFgrandcherokee
- Stealth Hidden Bass SQ Build - bit.ly/CAFstealthaudio
Here at Car Audio Fabrication I teach you how to Master Car Audio in an effort to Design, Build, and Install your ideal car audio system. Whether you are a hardcore basshead or a HiFi focused audiophile I would love to have you subscribe and join our community!
-SUBSCRIBE-
ru-vid.com_c...
--LET”S CONNECT!-
Website: www.caraudiofabrication.com/
Facebook: / caraudiofabrication
Instagram: @caraudiofab
Snapchat: @caraudiofab
Music:
Switch It Up - RU-vid Audio Library
Licensed under Creative Commons: By Attribution 3.0
Car Audio Fabrication - Master Car Audio - Design, Build, Install

Авто/Мото

Опубликовано:

7 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 1 тыс.

@CarAudioFabrication 6 лет назад

Hey guys! What other common mistakes do you see made by those that are new to car audio??

@theunion2021 6 лет назад

CarAudioFabrication for the 2 subs you use a stereo amplifier use a 8inch sub for tight bass and 10inch for deep bass you will have a very immersive experience and with a dsp you might be able to touch like 20-25hz have tested it you dont even need high power amps or subs

@damianlindsey6177 6 лет назад

Would just like to say I am a long time viewer but in regards to the hardwiring a head unit into a car, sometimes that is unavoidable. There's no dash kits or intall kit to put a head unit into a 1974 Chevrolet Vega hell, most people that aren't into drag racing don't even know what it is, they think it's an old Corolla lol. Everything else was spot on but don't forget that there are those of us out here with 30-70 year old cars that have been restored.

@CarAudioFabrication 6 лет назад

@damien Obviously there are cases where it may be required, but how many newbies are installing into classic cars? For 99.9% of cases there is going 5o be a harness

@noname-jx2rr 6 лет назад

I've been doing this since I was in high school, I'm 29 now. I have learned a lot just from watching these videos. One thing I learn is that gain is not volume nor does it mean the amp is not working it's full capacity. I've never blown subwoofers but I have blown plenty of midranges. My most recent screw up was I plugged my positive power into the ground connection on my amp and my ground into my positive. This got a bit heated. I just didn't look what wire I was plugging into what hole.

@chrisvinicombe9947 6 лет назад

The worst I think is installing a system without sound absorption/deadening. The horrendous rattling and vibration ruins the sound regardless of cost of components used.

@erickvazquez6491 4 года назад

I love how he doesnt bash but instead constructively explains why not to do stuff a certain way. great channel !!! thank you

@seanmichael2777 4 года назад

Aswell as his not condescending in his way of teaching which makes you feel so much more confident and interested in every single thing that mark says. I’m a mark fanboy 🙏🏼❤️

@slimwilly573 3 года назад

@@seanmichael2777 yes, he doesnt make you feel like your a complete idiot for the stupid things you did as a teenager with a brand spanking new license.. a honda civic hatch with the muffler cut off and a big air filter strapped straight to the intake.. cause race car stuff duh lol... he much more tells you in a way that its obviously has been more than just myself doing all this... get a set of subs grab the biggest amp u can come across slap it all in with a cut up drop cord lol... and blast it pissing off the entire neighborhood at 2am while every other speaker in the car have been so fried that the cloth screen from the factory has even came apart from the cones slapping against them... but yes we were "the shitz" back then... now days it's all about how clean it all sounds together while ur bumping some old jackson 5 at the red lights and the older people looking over and giving you a big 👍👍👍😎🤣🙃

@cooleynumpsey5084 6 лет назад

another newbie mistake is that people are worried about peak power rather than RMS power

@Highqman1974 6 лет назад

TRUE STORY!!!!!

@oneal738 6 лет назад

This is very true

@TheInstrumentalHeadquarters 6 лет назад

suprised he missed that one

@robertburchell 6 лет назад

People also forget that speaker sensitivity is as useful a measurement as power handling. As sensitivity rises, power requirements decrease for a target SPL.

@mrcheezle6 5 лет назад

Yes! I was definitely part of this when I first got into audio!

@northwestcustoms6663 5 лет назад

Whatever you do don't let the smoke out of your wires or componants, very hard to get back in.

@billwilliamson9842 3 года назад

that stuffs magic, seems to not work after it escapes

@steven_porter 6 лет назад

Years ago I helped a friend install a sub and new tweeters. We ran power through the door and mounted the tweeters under his dash using duct tape. Wires were connected by twisting them together and wrapping in electrical tape. Fortunately I did insist on properly using fuses right off the battery and there were ultimately no issues, but I'm proud to say we have sinced fixed all these mistakes and the car sounds great now!

@thomshere 5 лет назад

As far as I'm concerned this is one of the best channels on here for car audio design and installation if not THE best and I can't thank you enough for all the great videos. I think that one of the car shows on TV should pick you up for a design and installation show or at least a segment. Good Luck!

@Pinkielover 5 лет назад

how about mistakes made by pros that just wanna make a quick dollar

@Holisticxoxo 5 лет назад

When yo dad went out to get milk 20 years ago so now you rely on RU-vid videos for car advice.

@detox2778 5 лет назад

Ahahahaha , RU-vid has more knowledge anyways

@grindshine2439 4 года назад

Newports @ Budweiser

@inhawaii4941 4 года назад

Nah youtube just knows more

@markvandusseldorp3178 4 года назад

That's just ignorant

@reggieb5324 4 года назад

Mine never got milk. He just never knew shit 😕

@skimthechannel9437 6 лет назад

Newbie mistake: turning up everything on the amp

@tayeescobar5689 6 лет назад

skim the channel OMFG YES

@randomtube8226 6 лет назад

That has to be the most common mistake above them all.

@JLUnlimited 6 лет назад

skim the channel Another great point. . !

@ItzzSupah 5 лет назад

Me af 😂😂

@mrcheezle6 5 лет назад

Gain = "louder" haha

@festa289 6 лет назад

funniest one i seen was a guy whos amp keep cutting out, only to find he filled up his spare tyre well with dirt to "earth" his ground cable. he obviously thought it was the same concept as house wiring

@ArT2Oo0 5 лет назад

lmfao this cant be true

@WuClear 5 лет назад

No way 😂

@WuClear 5 лет назад

I can't believe this. Nobody can be that dumb. That had to be pre internet right?

@vipervidsgamingplus5723 4 года назад

ClearAlpha I watched a video where a woman walked around her tesla for ten minutes looking for a fuel port thinking her car ran on gasoline so yes even with internet this can happen easily

@philipgeary2132 4 года назад

I CALL BULLSHIT

@shedred1967 6 лет назад

My first mistake, using a battery isolater. Don't need that, wire amp fuse block/wire direct to back of alternator or battery. I always use a fuse as close to power source as possible. Great tips, thank you.

@corvettefever360 6 лет назад

I got my M.E.C.P. in '96. I have seen alot of these so called "how to" videos on mobile electronics installations & these have been some of the best. Glad to see people who know what they are taking about before teaching others. Keep up the good work!

@ricks8872 6 лет назад

My sister's boyfriend didn't fuse his power cable and it's crimped under the folding back seat and shorted out. My sister was driving at the time and had to stand there and watched vehicle burn to the ground on the side of a busy freeway

@CarAudioFabrication 6 лет назад

Ouch! And that my friends is why we use a fuse!

@allrimmedout 6 лет назад

But the fuse only would have saved his vehicle and he wouldn't have learned that he probably shouldn't be installing anything in the first place.

@ChristianAlmeidabr 6 лет назад

Oh My! Sorry! I hope nobody got hurt!

@kcgfy81 6 лет назад

Lemme guess he the ex-BF now? If not is she crazy? He almost got her killed!

@joshhagen4182 6 лет назад

Betcha he won't do that again

@ImAGoodBoy69 6 лет назад

You are my favorite audiophile on RU-vid, man. Your so professional, knowledgeable, and helpful. I love EXO and Soundman and Steve is king shit and everything but those are just vlogs, you make tutorials and that's what these new audio enthusiasts need! My Build: 09' Pontiac G5 Coupe -SUBWOOFERS/AMP- - Custom Design Enclosure - 2x Rockford Fosgate P3D4 12" - Rockford Fosgate R1200-1D Mono -SPEAKERS/AMP- - Rockford Fosgate T1650 6.5" Coaxial - Rockford Fosgate T1692 6" x 9" Coaxial - Rockford Fosgate R300X4 4-Channel -HEAD UNIT- - Sony XAV-AX100 -BATTERY- - HO3209 3200w Power Cell -EXTRA- - Fully Dynamatted - Big 3 Upgraded - Cosmetic Amplifier & Battery Racks

@Tlittle888 4 года назад

I love that you had a GXP for the vid. I have a 5.3 Monte and literally ran my power wire the same way you just showed!

@benwilliams9374 4 года назад

I spent several months and a little extra cash trying to rid my system of unwanted noise. Everything from alternator whine to power window and a/c blower noise coming from my amps. After trying a few things I learned from your videos, I have finally gotten rid of 95% of the noise. THANKS DUDE.

@davect01 6 лет назад

Good info. Plenty of newbies just want to shove a big 'ol woofer and get frustrated when it does not sound great

@bootysauce_ 3 года назад

I was brand new to car audio. Bought an 18 inch RE Audio sub with 5k watt apm, Made my own box with correct dimensions and had professionals install it into my vehicle. That thing worked flawlessly! I did exactly what you said lol. But it sounded perfect

@treydaypnw 5 лет назад

Bro you Run this car audio shit on RU-vid! We are Thankful and Appreciative of the Audio knowledge that you possess and share with all of us! Thank You!

@alexandersumrall6408 4 года назад

Mistake I made when I was in high school was using entertainment wire for the power wire. I was broke I spent all my money on the radio, amp and speaker. The wire melted like after a couple of songs lol. Another mistake my senior year of high school was putting in a 5,000 watt system into my car with all the right wiring but no capacitor and destroyed my battery lol. It would only play like 2 mins of a song and shut off and then when it had enough power kick back on and play two more mins lol.

@flaman78 6 лет назад

Yes, that discussion about fuses, types of fuse holders for the location (engine compartment or interior/trunk), circuit breaker style fuses and so on. That would be great. Thanks for always be so informative in the videos.

@allofmeirl 6 лет назад

Great video like always!!!

@dieseldiesel9292 4 года назад

As somewhat of a noob to car audio I'm glad my battery is in the trunk of my car from factory. It makes the wiring so much easier.

@Stretchman69 5 лет назад

30 years in the biz... Your videos are great!

@oldmenruleracing 6 лет назад

Missed seeing you for a while. Great video!

@MrSpanky473 6 лет назад

When I was about 17 (1990) I had an '85 Ford ranger, absolutely no room behind the seat.. anyways, I had 2-12" Kicker separates.. so I built a box out of 1/4" masonite, and liquid nails to specs, and thought I was gonna save some space... the box flexed more than the subs 😑

@juspatmil 6 лет назад

Sinister hahahahahahahhaha young and dumb..... I def had an engine fire at 17 due to no fuse.... Never again..... Now its a father and son Hobbie

@josh33025 6 лет назад

I cut a triangle box down some so it would fit behind the seat of an regular cab f150 for 2 12's.

@nzpancakes 6 лет назад

josh33025 did it work?

@justinornelas4569 6 лет назад

Funniest thing I’ve read always use wood glue and ALWAYS have a fuse under the hood or near the amp as well never turn all of the gains to right lol unless you want high frequency distorted bass

@nzpancakes 6 лет назад

Justin Ornelas did it sound good is what I meant

@johnsmith-qz4bv 6 лет назад

another mistake is maybe miss calculated budget it ends up costing more then they thought..?great videos..

@corvettefever360 6 лет назад

That last part is so true. I very rarely hear professionals bring this up about mix & matching subs & sub boxes. I would also like to add that doing this can also create major phasing issues amongst the things that you mentioned & a few others

@theminifigpig 6 лет назад

Look how far you've come bro, your shop looks amazing. I remember watching your Kerfing wood video years ago. As always Mark your videos are incredibly useful. I watch them whenever I'm beginning a new project. Keep up the good work bro. And thanks again.

@SPLEclipse 6 лет назад

If you're going to do a fuse video I'd love to see a "fuses tested" video to show how long and at what current different fuses blow. See if buss fuses are faster than ATC, see if cheap ANLs take longer to blow than expensive name-brand ones, etc.

@lanceherr6466 3 года назад

Can you hook up 2ohm and s 4ohm sub to s mono amp their in the same box

@1HotLegendLS 6 лет назад

I'd love to see a video on fusing dual battery set ups. Even on professional installs I ever see a fuse at both sides of the wire run. What I mean is a fuse close to the front battery And a fuse just before the auxiliary batteries.

@jameselam8263 6 лет назад

1HotLegendLS they should be of the same size and within 18 in. of each battery. And the secondary battery should have another fuse on the output to the amps. The ground for the secondary battery should be as short as possible, and your good to go!

@1HotLegendLS 6 лет назад

Jim Elam exactly! That's how I do it.. but I've seen professional installations with just the fuse at the main battery. This should be touched on so others can know why.

@jameselam8263 6 лет назад

1HotLegendLS yeah I've noticed that. I don't know if they aren't showing it, or if they aren't using them. It's a big mistake if they don't.

@brandonisaacson5193 2 года назад

Thanks for all the tips. Your channel is awesome. All love

@eddiedow3757 5 лет назад

I like how you try to teach newbies the correct building techniques. Some will never learn because they was told other wise by someone they know.Heck I been building systems for over 30 years and I still learn new and tricks of the trade. I have learned how to make the aesthetics of the system look very unique. This kinda makes a signature mark for your builds. A bit like my favorite saying (by JL audio) this is how we play, every know thats JL's trade mark. Thanks for all the info I have learned Mark

@paulfretz9486 6 лет назад

My all time fav. The guy who took 4 12 gauge wires twisted them together, used four crimp on ring connectors, attaches those to the battery each one has a 30 amp fuse then stretches them he length of his big ass Lincoln town car and hooks them to a thousand watt amp. His theory was he met the fusing requirement and the four wires would carry the current since the same wire carried 480 volts for a industrial motor he uses at work.

@Finkledbody 6 лет назад

Nothing wrong with that. 1. Its a Lincoln. 2. its okay if it burns 3. refer to #1

@brianhummel8659 5 лет назад

Holy Sh**..........that's funny. Do people really not understand that's 3 Phase with a ground? Also, in electronics the higher the voltage, the lower the current if everything else is equal. Basic electronics, some of these comments are truly unreal.

@danp5421 4 года назад

@@brianhummel8659 i am people could you elaborate

@kw6798 6 лет назад

I saw a Chevy Tahoe were someone cut the wires On the obd2 plug to power their head unit and grounded the speakers to the seat belt bolt.

@Imtrappedintheinternetsendhelp 5 лет назад

What's wrong with that? Sounds like a standard operation. 😂

@benjamindelgado8979 5 лет назад

Lol that is funny

@GlycerinZ 5 лет назад

wow, shit I couldn't even imagine in my head until I read it!

@brettbogdanich7731 4 года назад

That's custom right there ...

@thelastskullripper6383 6 лет назад

Mark, I would love to see a fuse vid sometime! Since started watching your vids I have become a lot better understanding car audio because of how detailed you are.

@kiasohc 4 года назад

Enjoying your videos bud... they're a big help!

@kdash3215 6 лет назад

Great video. I used to work as a Hyundai dealership technician and we once had a car come in with a massive audio system. The customer picked up the car after the routine maintenance and recalls were completed. Low and behold, car gets towed back, no start issue, no electrical power whatsoever. Well his amp power wire came loose just before the fuse and grounded on the PCM, absolutely frying it to smithereens. He tried to blame it on us. It was clear to us his audio work was performed at an unqualified shop.

@DiyAllaroundguy 6 лет назад

Requesting a how to video on how to match frequency with head-unit, crossover/dsp and amplifier with the frequency range on inside speakers/subs

@brennoncook6279 6 лет назад

Larry agree

@jameselam8263 6 лет назад

Larry if your using a dsp you set it on the dsp and leave the head unit and amp on full range. If the dsp doesn't have a subsonic filter set it on the sub amp.

@DiyAllaroundguy 6 лет назад

Jim Elam thanks , so it is better to let the dsp do all the work rather that match the frequency with all three units. Radio, Dsp, Amp

@ronaldbaezvicioso6681 6 лет назад

Larry roberto

@vincebowling1778 5 лет назад

I actually made the mistake of building a subwoofer box that was too big to go into my trunk years ago. Since then, and this is just a suggestion but yet it has worked for me many times since my boo boo back then...I determine the size of enclosure I need to work for the sub or subs, then I'll take oversized sheets of plain cardboard, measure and cut them to the size the actual box will be, then make a "dummy" model out of the cardboard to the exact size specs, then check the fit. If the "dummy" cardboard box will go in without fail, then I'm good to go with my final build. If not, then back to the drawing board. Thanks for your videos, you have been a lifesaver, (and money saver) many times!!!

@mobleyMobley 5 лет назад

I mixed 2 12's in a bandpass and 2 10's in sealed, with separate amps. Sounded good.

@randomtube8226 6 лет назад

People who think the gain adjustment on an amplifier is a volume knob. People who buy powerful amplifiers and still have the stock alternator and battery. People who think capacitors actually fix their voltage problem. People who use speaker wire as power wire. People who think plugging up a ported box makes it a sealed box. These are the most common car audio mistakes I've witnessed people do that I dont think was mentioned in this video. That I can think of off the top of my head.

@drupey1878 5 лет назад

Random Tube - I’m slowly purchazing a new audio system, I bought the Rockzford r-1200 and next the 2 12” P3’z, what battery should I get and how many amps should my alternator have? Thankz.

@PimpsMomma23 5 лет назад

Shit I'm running 3 skar ddx 12' s, a sundown u series 15 , 4-- 4x6 Rockford's, 2 3.5" Rockford tweeters and 2--1.5" jl tweeters when was I supposed to get a new alternator or capacitor...??? I bought a $100 deep cycle amg battery from O'Riley's built and carpeted a little box that's attached to encloser not a single light flickers done this with every install I've ever done with more then a single 10" sub. As long as you understand the correct way to install and wire all your components in the vehicle car audio falls under the k.i.s.s. guidelines keep it stupid simple !!!

@b.myhrer2427 5 лет назад

I'm getting myself a 10.000WRMS 15" Ground Zero sub shortly. the amp is roughly 10.000W mono. I'm changing my main battery, and i'm adding another battery to keep beneath my trunk just for that amp. Supposedly it's no need for a new alternator.. but we'll see about that :P

@DJP4Liberty 5 лет назад

Stock alternator and battery performance can be GREATLY improved with larger diameter alternator/charging and grounding wires.

@brianhummel8659 5 лет назад

@@b.myhrer2427 It just depends on how many amps your alternator produces and the drain on your battery(ies). Not too hard to figure out if you know what you are connecting. For example, if you alternator pushed 40 and between the two batteries you are pulling 41, eventually one, if not both will fail overtime. Add up the amp hour ratings and you are done. Just keep in mind amp hours are determined by draining the whole battery. If you want to start your vehicle every time need to complete some research on your batteries to find out how many amp hours are stored before falling below the cranking amperage needed to start.

@Oystein87 5 лет назад

Overpower the speakers? It's always better to have a bigger amp than needed than a too small amp or a "just big enough" amp.. And orginal speakers can handle ALOT more power when you use the high pass filter. So often you don't need to upgrade the speakers unless they are really crap and have bad sound. That's something I have learned after years of working with stereo upgrades.

@steventhomas5865 5 лет назад

I like how good factory speakers can sound with a crossover and high quality amp.

@exitdown 5 лет назад

absolutely - bass takes way more power to produce, if you reduce the bass on the factory speakers 25-40w rms of mids/tweets can easily keep up with 300w of bass. selling someone a amp they dont need is a sales tactic hahaha

@jaredandcande11 4 года назад

Absolutely imperative for any success installing a system. Respect brother. Your doing it right, and just fine. Of course, nobody wants to think they are completely ignorant and I wish you could reach more folks but to do so you would actually have to bait them by providing a much desired byte of info mixed in with the don'ts. These days, those same ones who need it wouldn't have the patients to watch the entire video. Again, your doing great, keep it up.

@gobbly1337 5 лет назад

Like your videos. I'd love to see you dive more into detail on some of these topics like line resistance.

@jessebellis478 6 лет назад

Nice information !! love your videos !! awesome !!

@jasonmoriset9292 6 лет назад

Great information! I'm glad I stumbled on your channel. Nice to see someone big in the industry sharing instead of hiding all the secrets. I have a question. I drive a sedan. I have plans to replace all OEM parts, front to back. I like full spectrum sound quality. I have no plans to make anything competitive. It's just for my listening enjoyment. I have a 10", 4 component separates, and a head unit while looking for amps. I wanted to use the 10" but also use an 8". No pairs of either, just one each. If I use a separate amp for each and sealed each chamber for the 8" and 10" so no air is shared could I still incorporate them into the same box, side by side? After seeing this video, you make me skeptical this is a good idea.

@fafazaj6726 5 лет назад

Jason Moriset make sure you run them of separate amps. but you can build a box to house diff size speakers. but chambers have to be different sizes for each size sub required. it's a bit harder box to build

@brianhummel8659 5 лет назад

Unless you have the boxes fabricated exactly, the amplifiers are exactly in-phase, and the reflections do not cancel each other, yes go ahead..............but good luck making that a reality. Some systems that cost tens of thousands of dollars to design fall short. Now, once in a blue moon someone gets lucky and then they get people to believe them and the cycle of ridiculousness is continued.

@manwhosold111 6 лет назад

Awesome explanation of fuses and the fire safety. thanks man!

@Mike-zn9xt 6 лет назад

Great video 👍 thanks for making it and sharing

@jiveturkey947 5 лет назад

This video is better titled “mistakes we made in high school to our first car”. I think I’ve done all of these in my first car back in the day.

@miata350 5 лет назад

On my first car when I was 15 I didn't know how to pull the deck, so with my amp install I crawled under the dash and plugged in the rca's blindly. Then I ran some really cheap 8ga Radio Shack power wire to a really cheap rocker switch and used the switch to turn my amp on and off. It worked but I can't believe I didn't set my car on fire.

@racerx9223 5 лет назад

I always liked the idea of having two different sized subs, a 8 for the punchy fast stuff and a 12 for the actual bass, I feel like someone could get better sound with both if done right. Like you said though, the would need separate signal and power supply to be done right. Luckily I'm indecisive and have studied way way more into understanding stereo equipment than I've needed for the projects I've done LOL!!!

@smokegraffitiSFM 6 лет назад

u do some amazing install ideas 10/10!! love the attention to detail ;)

@vernonwilliams8644 6 лет назад

I read that you should add 60% for cheap wire. Mybe add that ofc wire vs coated aluminum wire.

@World_of_Tanks_EU 6 лет назад

Vernon Williams is a great resource

@yachtyteam6978 5 лет назад

Ok man enough hating on my system!!

@FlethooTv 4 года назад

Yachty Team real talk 😭💀

@montexanfpv2624 3 года назад

My 96 ford TBird LX was a fun project. I actually just did my first system in. And what a car to do said tasks. Ford premium sound had to go. Running power wires from the engine bay to the trunk (passenger side) . Audio wires from the trunk to the dash ( factory amp bypass) under the back seat and carpet through the center console. And RCA are ran on the driver side under the kick panel. 1 million miles of wire later the sound system in the almost 30 year old girl sounds damn good. Allot of info retaining and gathering later, all thanks to the wonderful RU-vid!!!!

@russsmith9042 2 года назад

Yeah Mark thanks for all your informative videos you really know your stuff I've been doing this for 35 years and I still learn things from you everyday I watch a video. So for all you know it all's out there huh I suggest you keep watching Mark he's not perfect but I can guarantee he's better than 95% them out there. Thanks again my friend.

@rescuejunky1660 5 лет назад

I've seen a guy use a plywood sheet to mount the sub and use 2x4's as legs. This is not a box. It was his first sub so I had to build an enclosed box for him.

@crippycipps1002 4 года назад

It's good of you to do that for him, I just built my first ported box for my 15 and I'm pretty happy with it

@TomMusick 6 лет назад

"start on fire"

@CalebEmbry 2 года назад

Commenting for the algorithm. This guy helped me a lot when setting up my system.

@raikou889 5 лет назад

currently running a 10" rockford fosgate sub and a 10" Kicker sub. was aiming to build a punch system. turned out pretty well.

@Mrcaffinebean 6 лет назад

I had a mechanic tell me that my fuse setup was wrong and that it should be on the negative side of the battery 😂

@fornarnia8 6 лет назад

Lol. I had a Mechanic tell me my wire was "too large" and I needed a capacitor.

@Mrcaffinebean 6 лет назад

John Smith lol now that’s a good one!

@godzillasballs 6 лет назад

John Smith technically, current does flow from the “negative” which is actually positive but we keep it that way to respect the man who caught electricity in a bottle...

@allrimmedout 6 лет назад

Power wire can't continue to short out if the ground circuit is broke. 🤷‍♂️ so technically fusing the ground ... if that run is the only ground feed to the battery would work, but positive is usually more dedicated.

@gta4162 6 лет назад

Mrcaffinebean no...

@vancewanless4525 6 лет назад

What about when someone keeps blowing fuses so they just put larger ones in there!! Ahhwww my God don't do that ever!!!!!!

@WeirdJerz3y 6 лет назад

Vance wanless I hate that so much. I seen installs 10gauge wire with 100amp fuse. And wondering why the amps don't sound good or keep cutting out.

@TheMetalheadHomestead 6 лет назад

Funniest fuse fail I've witnessed was a bolt in place of a 10A glass fuse. I've also heard stories of people using 22LR shells after blowing fuses.

@vancewanless4525 6 лет назад

Don't forget about the ever so handy tin foil wrapped around the fuse after it has blown!! Cringe.....

@jeremybaxley5848 6 лет назад

Foil out cigarette pack wrapped around fuse!

@doseofmoe1102 6 лет назад

Vance wanless Hi. I just had a JL audio 750/1 amplifier installed to power a Jl audio 12W6v3-d4. I have a RLC bass controller knob in my dash that is running to jl HD amplifier. I have an in-line acu fuse that is rated at 80 amp. For some reason when I turn the bass knob to about over 60 percent the fuse blows. Do you have any idea why this occurs? I was considering getting an ANL FUSE at 150 Amps. Noob here thanks

@ailnwoodconnor8874 6 лет назад

Thank you for everything that you taught me and done and don't worry about them other RU-vid guys that's hating on you keep on doing what you doing you're doing a great job PS thank you for everything

@agentredbone1667 3 года назад

I'm new to car audio. I mean I had systems in my car as a teen but ended up having kids as a teen so now that my kids are all grown up I've gotten back into car audio again.

@flacko5894 5 лет назад

Idk how to do any of this so I guess I’ll just take it to a professional

@GlycerinZ 5 лет назад

It's actually pretty easy once all the info clicks in your head. Just keep watching until you understand, then you can do it yourself!

@ericguerrero3656 4 года назад

Any specific videos recommended?

@R3MIXMODZ 6 лет назад

I have been learning about car audio for about 4 years but the silly thing I cant grasp is how to figure out wire gauge.. Its hard for me to figure out how much current is flowing through my wires so I dont know what gauge to use. Or even when powering amplifiers.

@godzillasballs 6 лет назад

R3MIX MODZ follow online chart. Go with OFC wire, double size for CCA.

@bergentonpeppercorn4962 6 лет назад

Look for the amount of amperes the piece equipment you’re installing pulls. Then refer to an amp chart, which will give you the proper gauge wire for the distance. Most amps and stereos will give you the average amp current and then the recommended fuse to use.

@jameselam8263 6 лет назад

R3MIX MODZ look up the ohms law equatio and use the power ratings of the amps etc for the math. Ohms law will give you amps, volts, and wattage depending on how you enter the info. Also you are usually safe using this rule of thumb use 8awg for up to 800 watts total system power, use 4awg for up to 1500 watts and 1/0awg for up to 3000 watts. Over that then you need to start making multiple runs of 1/0awg. Fusing you need to use 10 amps of fuse for every 100 watts of system power. I hope this helps you.

@Exterminatingtraper 6 лет назад

Use the biggest wire your amp can handle, a normal car audio install has roughly a 17-22' power wire length if the battery is up front, my rule of thumb is under 500 watts 8 gauge and 500-1200 4 gauge and anything over use 1/0

@austinpotts35 6 лет назад

Y'all are more generous than me haha it's 1/0 to me if it's 1000+ system power. In my next set up I'll have 1500 for the sub and 250 for the doors I'll use a single 1/0 to the amp rack then 4 gauge to the amps from a distro block roughly 6 inches away.

@djstikzo9431 4 года назад

I have learnt something today, and proudly so. The mistake I made is installing the wire fuse far away from the battery, so the short end in closest to the Apmlifier!!!!! but after what I have learnt I will make a plan to avoid catching a fire; thank you for this informative video.

@harryseymour6886 6 лет назад

Great video mark I'm not new to this however I do still learn a lot from you I would like to have you go more in-depth into some of these mistakes because I believe it would help a lot more people out always love your videos and the attention to detail that you put into your builds

@premise187 5 лет назад

Why aren't we talking about 12v circuit breakers instead of fuses?

@Veritas-invenitur 5 лет назад

If you are ever in a situation where either your fuse blows or your breaker trips then one of the following is going on. #1. Undersized fuse/breaker and most likely undersized wiring. #2. A short. #3. faulty equipment. These three situations SHOULD be RARE so their is no need to use anything but a fuse. Besides Fuses trip twice as fast a breakers do on a DC system and 8 times as fast on an AC system.

@brianhummel8659 5 лет назад

@@Veritas-invenitur No offense, but this is complete bs. It all depends on the curve of the CB. To make a statement of definitive 2x 8x is ridiculous.

@Veritas-invenitur 5 лет назад

@@brianhummel8659 Your comment is ridiculous. The trip times are well known and thoroughly established facts. Different type fuses just like breakers have different trip times however in most cases my figures are the accurate.

@VVarpedVVarriors 4 года назад

I kept blowing my fuse on my SoundStream amp for my subs. So I went to the store and cut a 3/8 bolt the size of my fuse. Never blew again. 👊😎👍

@SuggahBear 6 лет назад

For me? It's the general knowledge about the audio upgrades I want to do; increasing my knowledge daily✔

@dustylee8111 4 года назад

Thanks man these videos were a big help

@elliotburnstein7676 5 лет назад

Build your box WxLxH, out of cardboard then test.. Dont waste the wood....

@ruikazane5123 6 лет назад

The common fault when buying equipment would be sticking on a brand[Alpine lover here], hahahaha

@gabrieljenkins346 6 лет назад

I’d love to see more car audio videos dealing with wranglers like how to increase bass without a sub woofer, or how to get great sound with the top off!

@MephistoRolling 5 лет назад

when i first started i remember one of the big mistakes i made. took 2 amps blowing to realise. i bought an amp that matched my sub ohms, but i had 2 subs, and bridged it.... blown amp after playing for a few minutes.

@jamesmiller8390 6 лет назад

What if they don't sell a after market wiring harness for what I drive

@jtwmadman2854 5 лет назад

Some company somewhere makes harness adaptors for 99.9% of all makes and models...

@fafazaj6726 5 лет назад

James Miller a good car mechanic shop can trace what's what in the harness. depending what car it is it's pretty simple to trace positive.negative and rest of the wires needed to swap after market CD player.

@LionWithTheLamb 5 лет назад

I would just solder in pigtail wires to the current ones and leave the factory plug in place.

@detox2778 5 лет назад

@@jtwmadman2854 that's not true at all , the isnt one for my car either

@brianhummel8659 5 лет назад

@@detox2778 If there's a harness, that harness had to plug into a radio at some point. Like JTW said, unless it's from the 40s or 50s I would bet money some company or junkyard has the connector.

@ConnorCarrell 5 лет назад

When people only twist the wires together then use electrical tape.

@niro56 4 года назад

Sure fire there, it happened even on my motorcycle, a guarantee it would on 100+ amps..

@NateNoShlong 4 года назад

Connor Carrell I did that on my speakers lmao

@Cdogg2233 5 лет назад

Can't believe after 10, you still haven't hit my biggest one when I started, understanding ohms and how to connect DVCs or multiple subs to a monoblock amp

@VonSpud 3 года назад

Great stuff thanks 😊

@ImDanimal85 6 лет назад

Newbie mistake is not understanding ohms!

@trapperkreeper6105 5 лет назад

I don't even want to! I hate ohms

@justinrogers1807 5 лет назад

I don't!!!

@martinentertainment734 5 лет назад

ohmmyGod...

@GlycerinZ 5 лет назад

Ohms are important! My buddy had two Klipsch floorstanding speakers in his room connected to an Onkyo receiver. If he turned up the volume too high, the receiver would cut out, and it would get HOT. I looked at it and noticed the speakers were rated at 8-Ohms, which the receiver did not support. Luckily there were two sets of speaker connections on the back, wired them in parallel for 4-ohms and connected to the receiver, problem solved.

@snap-off5383 4 года назад

@@GlycerinZ Any amp will support a higher impedance load. There was something else amiss in your description. A higher impedance always means less overall current (and less heat) not more.

@dingleburry7919 5 лет назад

I cut my harness. Fite me.

@TheSpazzattack95 4 года назад

A noob if u dont cut it hardwire is the way to go

@snap-off5383 4 года назад

@@TheSpazzattack95 Yeah I think buying a 40 dollar "adapter harness" instead of doing 10 minutes of soldering and heat shrinking, is being a "more money than brains" noob. The only usefulness of them is for people who literally have no idea what wire goes to what.

@slow_rednline4874 4 года назад

@Chad Wilkins I agree with you

@jacobd9275 4 года назад

i’ve been waiting until i get a new subaru (my attainable dream car) before i messed with this stuff and now i’m at the point where i can justify getting one and starting on the audio, can’t wait 🤤

@Bamocratic 3 года назад

Loving that ti-83plus silver edition calculator! Mine finally fried after 20+ years

@eagle2032 6 лет назад

The worst mistake is owning a system and not owning Killer Quad: The Best of Newtown Vol. 1

@LionWithTheLamb 5 лет назад

Kickin' it old school yo. Techmaster P.E.B is the best.

@SwagA52298 6 лет назад

When it comes to wire, I just use the biggest wire the amp will take.

@billwilliamson9842 3 года назад

then you have to check out if its solid copper or that copper coated aluminum, solid copper is always best.

@erikdickerson929 3 года назад

This was a very educational video just put my first one yesterday only did one of these things 😂

@mrjohnsir1335 4 года назад

Love ur videos bro keep up the great job. U do such professional work if everyone did work like you the world of car audio would be perfect....

@josea.garcia3994 6 лет назад

Those we're some great tips of advice Mark!!! 👍👍👍

@edgaradorno2979 3 года назад

Thanks bro ur video r very helpful

@spencertaylorcrowe 4 года назад

Tip 3 I upgraded my door speakers with 6.5 midrange woofers. And the back 6.5 full range speakers in the trunk. But I still get some distortion at higher volumes.

@vincentfisher5895 3 года назад

Very informative videos.

@jimbobrennan8011 4 года назад

Thank you for the info!👍

@mr_mcgrew 3 года назад

Regarding boxes fitting through the trunk opening, I have learned this the hard way, one time. My preference these days is to make a cardboard mockup of the box, pod, bracket, or amp rack, and use that to check fitment. It's cheap, fast, and easy.

@dcfla755 5 лет назад

Great info vids you put out, my friend. Ran across your channel looking to stop vibration in doors. Another great video I must say. You have won me over; liked and subbed. Will be checking out more in the future! Thanks again

@thejjgang6338 Год назад

My dad literally has installed many many many car decks, just cutting the harness, it’s so much better when you know how to do it

@edwardr7577 4 года назад

One of the best "mistakes" that I heard, was when I was planning an 18 speaker in stall into a totally fiberglass car. No chassis. I was told that because I could not use the body as the earth, it would not work. What I did was to match the grade of wiring from the battery at the front of the car to the distribution points at the rear of the car. Positive side has the primary fuse next to the battery, and then a fuse distribution blocks at the back. The head unit and DSP on the dash picked up their power from there as well at the 4 Alpine V12 amps at the back. All the units using power were returned on the earth side to more distribution blocks mounted at the rear and then returned to the battery just like the power side. Worked at treat. Was safe and gave a great sound no issues.

@seansean8008 2 года назад

My biggest mistake was finding car installation shops that just threw equipment in, but never took the time to realize that an upgrade is not universal and not necessarily an improvement. Ex: my Challenger with Alpine factory system- upgraded speakers and it sounded bad- lower volume and rear speakers drowned the fronts. The factory amp was pre-set to send only certain signals to certain speakers and used 2 ohm speakers. The 6 ohm dash mids replacement were drowned by the back. The install crew should have known the problem. It took me a long time and many videos like these to figure out the problem and to eventually make further changes myself to correct the problem.

@moreaudio760 6 лет назад

Mark ...love the videos buddy keep up the good work ...I’ve seen more and more installers getting creative with LED lighting ...could you make a video showing various led instillations and proper wiring for these setups ...came across an install the other day were a customer had lighting installed in his car ..must have been 15 meters of lighting on a 20 amp rocker switch ...car nearly burnt up ...rookie mistake ..got home squared away with a multi relay pack to distribute the load evenly ......keep up the good work buddy

@emo65170. 4 года назад

I'd even recommend starting the hole in the firewall with a step drill because the step drill is easier to control. A typical fluted drill bit is designed to pull material out of the hole it's drilling. Once you break through sheet metal the drill bit is going to pull the entire length of the drill bit through the hole potentially puncturing something on the other side.