Drivers Side Wheel Speed ABS Sensor Replacement on a 2010 Chevrolet Traverse / Acadia / Enclave

Подписаться 2,4 тыс.

Просмотров 20 тыс.

50% 1

A little maintenance is required on my mom's ride. Block heater cord repair, Air box removal and a drivers side front wheel speed sensor replacement...well at least what I thought was the sensor.
In this video, I'll try and clearly go through the process of removal and install of the new sensor.
The ABS, Traction Control and Stabilitrak warning lamps are all on. We are also get a C0035 code for the left front wheel speed sensor circuit which I believe is the issue.
This procedure should be very similar for the other Lambda platform vehicles such as the GMC Acadia and the Buick Enclave.
Thanks for watching!

Авто/Мото

Опубликовано:

17 фев 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@myfamilymatters 2 года назад

That was mind boggling to go through all of that work. Can’t wait to see Part 2. Great job and amazing filming. Your property looks so beautiful and peaceful. I’ll bet that the only sounds to be heard in such a serene setting, are those of you clinking and clunking away at rusty bolts on the car.

@harleyjonesrr Месяц назад

Thats a Magnetic ring thats part of the bearing. Great job thanks

@NorthernHomeGarage Месяц назад

Thanks for watching!! :)

@scottl7934 11 месяцев назад

Just did mine yesterday. What a pain in the a$$. Your video was very helpful. Had to drill my sensor out as well. Getting that "kidney" shaped attachment on the air box lower housing was very tough. Mine was loose as well...wondering how long it was loose and what the heck that thing does. Hopefully never again! Thanks for the video.

@NorthernHomeGarage 11 месяцев назад

Thanks so much for watching. I’m really glad it helped!!

@adrianvenegas6402 Год назад

Thank you for your advise great video

@NorthernHomeGarage Год назад

Thank you. I really hope it helps.

@Ang3l-of-M3rcy Год назад

So, the sensor was not the problem, it was the bearing. I was thinking about changing all my speed sensors along with the bearings. If after I change out all the bearings and if any of the sensors is bad I will then change them all. But for now, ill just focus on the bearings.

@elipsorange 2 года назад

Damn, I need to do mine also. I have a 2014 though. Hope it isn't too difficult. Great job on the video and very helpful

@NorthernHomeGarage 2 года назад

I'm glad it helped! I'll be changing the hub this weekend to finish the repair. Make sure you check that magnet ring on the back of the hub before condemning the sensor. Learn from my mistakes lol. Thanks for watching.

@richardbrown8794 Год назад

Thanks so much. i did not know .the plug is behind the air box.

@NorthernHomeGarage Год назад

I’m really glad it helped!! That just made the video worth the effort. :)

@richardbrown8794 Год назад

@@NorthernHomeGarage i put a drywall screw in mine.then used a cat paw crowbar to grip screw with heat on base to pull it out . Mine was corrided bad .used a round file to clean it up.thanks again.

@dennisb933 Год назад

Which obd reader is that?

@NorthernHomeGarage Год назад

It’s from Amazon. Blue Driver obd2. amzn.to/43nwSXh

@eliallen2596 5 дней назад

I have 2 code readers and they don’t pick up abs codes for some reason, now I am tempted to get this one to figure this out on my traverse

@bosaadbosaad6792 8 месяцев назад

its magnetic

@NorthernHomeGarage 8 месяцев назад

Yes the ring on the back of the hub is magnetic. 🧲 :)

@philipholman9898 2 месяца назад

Almost ten minutes in and we are not at the abs sensor 🤷

@NorthernHomeGarage 2 месяца назад

Yaaaa you know. My older videos I was full of hot air lol. Thanks for using. The FWD.>>

@dalejoreye839 5 месяцев назад

I need to do this!! Good video. Does not look fun😢

@NorthernHomeGarage 5 месяцев назад

It is some work that’s for sure. Thanks for watching and I hope the video helps.

@barryrenouf3450 6 месяцев назад

You should watch utube videos instead of making them.

@NorthernHomeGarage 6 месяцев назад

Nah, I'd rather be the one making the videos and entertaining people. It's just more fun that way! But hey, I have had you comment on both my Traverse videos now. Remember this one on my hub video? "Have you tried professional help?" Not very nice comments lol!! Thanks for boosting the algorithm!

@barryrenouf3450 6 месяцев назад

Did I say "You should watch u-tube videos instead of making them"? If yes then I repeat. .@@NorthernHomeGarage