Dual Mass Fly Wheel VW T5 T6 DSG - Easy Remove and Replace DMF 

It’s a motivational channel. 😂 Easy in hindsight. We Cant let these DSG’s get the better of us ! You can do it 👍

Absolutely, the video shows you the way. Let's us know how it goes. You can do it 👍

Thanks for the feedback. You can do it 👍

Thanks for the positive feedback. Let us know how you get on with the job. You can do it 👍

Hey thanks for the feedback. Keep us posted on how you get on with it. You can do it 👍

Well done, That’s why I stuck with FWD and snow chains . You can do it.👍

Thanks for the feedback. Keep us posted on how it goes . You can do it 👍

Thanks for the feedback. Keep us posted. You can do it 👍

Thanks for the feedback, lets us know how you get on. You can do it 👍

Yes. You can do it 👍

Thanks for the feedback , although not everyone has access to a 2 poster. You can do it 👍

Try watching my video with DMF sounds. It explains. You can do it 👍

Thanks for feedback.Havn´t had to do that job yet so no video from this channel. You can do it.

Yep it's a 7 speed dsg box. It's easy to do if you follow the video to see what's involved. If the garages are refusing to do it then they are not very experienced in VW's. The difference between the 7 speed and other dsg's is that the clutches are wet and inside the gearbox. They may be thinking you want the clutches replaced which is big job. Changing the DMF is easy as there's no clutch to undo. Hope this helps. You can do it 👍

Hi if you watch the video I show how to get it off. No oil comes out. Keep posted. You can do it 👍

@@youcandoit1828 I didn’t see the stub shaft,only the driveshaft sorry

@@bu4komobil hi just so we understand what do you mean buy stub shaft ? You can do it 👍

If I remember I show a pic in the video. I noted how far the old one was in and made sure it went in same depth. When I get a chance I’ll re watch the video. Let us know how you get on. Shifting issues should not be a problem as it just supports the end of the shaft. You can do it 👍

If you are talking about the 1/4 for torquing the flywheel bolts. I just do a visual 1/4 turn by noting where the handle of the wrench is. Looking at the video it looks like the needle bearing is set in about 4mm deeper than the edge of the hole your setting it in. Theres also a small hole in the end of bearing cage which you can use the see and test its seated correctly. You can do it👍

Agreed you can do it. I was thinking you get to this point as you have to really yank the drive shaft out. Much harder than feels normal. Have a big lever between the back of the DS and against the box. Max sure it’s on a sturdy part of the box so as not to damage. I did it from under. You can’t slowly spring it off by hand. Needs to be hard sudden force. Lever the DS so the clip is under a bit of tension then give it a yank and it’ll come off. You can do it 👍

@@youcandoit1828 I got it out, but my DS has a female end with the male stub shaft coming out of the gearbox. I see your DS has the male bit with splines and the clip at the end. My clip was on the stub. However, there was no clip I think. I can't find it. I mean, there must have been a clip, but it's not on the stub DS in the groove. I can't imagine I am simply meant to slide it back on without a clip there...right? It's mind boggling really. what an adventure!! you make it look 1000 times easier...my hat's off to you mate.

@@bradfordgoerss3242 well done. Indeed there should be a clip. Can you send a pic ? You can do it 👍

The CV joint at the wheel side fits on the male side of the drive shaft.

I will post a video to my channel and send you the link. cheers

Luckily I haven’t had to change the clutches just the DMF. You can adjust the clutches with the correct software and that might get you out of trouble. Haven’t done it my self thou. If it’s slipping in gear then definitely the clutches. You can do it 👍

@@youcandoit1828 are the clutches easy enough to change? I take it you would need to open the gearbox up? Can you buy a clutch kit for it?

@@mandylad I saw a video online about changing clutches on a dsg not this exact box but gives an idea. Check out RU-vid. You must be able to get the clutches from TPS if in the UK. Hope this helps. You can do it 👍

@@mandylad This should give you a head start... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-AKzjIHNLKz8.html Not to steer you away from You Can Do It, just reference YT video in regards to clutch overhaul.

Hi not sure as don’t have details to hand go with what the manufacturer recommends. You can do it 👍

Thank you for the nice reply. I have a question. I have ridden the Fulan twice and it broke. After the break, the car started to move with a sound and no speed. What do you think is the reason for this thing? Do I have to walk it quietly for a certain kilometer in order to respond to the boats?🥰

I never took the clutch off. It's a DSG with the clutches inside the gearbox. You can do it 👍

I got mine from Amazon or Ebay. Not expensive… Hope this helps. You can do it.