Dyson DC04 Bagless Vacuum Cleaner Power Cord Repair - A Simple Step by Step Guide 

Super accurate and super helpful. I followed this to the letter (word) and have a fully working DC04 once again. Thank you.

Thank you so much for posting this! My power cord had exposed wire that I've used electrical tape on and that wasn't holding anymore. I watched this several times, pausing as I fixed mine and the vacuum cord looks great and best of all, works. You saved me a lot of money should I have gone to a repair shop. All I spent was $3.23 for connectors. Thanks again!

Another great DC04 resurrection video, hehehehe! I've done this a couple of times as despite the "strain relief boot" the cable still does have a nasty habit of suffering from fatigue fracture in that spot. My cable is now a fair bit shorter but fixed for nothing!

Thank you! Was quoted a fortune to fix it and have a new cable fitted - fixed in 10 mins thanks to this

Thanks. Without your video I would never have worked out how to remove the switch. Best vacuum the DC-04 Dyson. Kind Regards. Terry, Liverpool, UK

Thanks, my Dyson now works perfectly again.

Thanks for the video... my wife broke our DC28 by stepping on the coord... I watched your video and had enough confidence to give it a try... ...SUCCESS!

Very helpful instructions which enabled me to get our DC04 operational again. However, a couple of suggestions: 1. The yellow power button on ours simply wouldn't budge, despite me having the prescribed removal tool for the job! I, therefore, bought a replacement (easily sourced and cheap) and simply drilled the old button out. Shouldn't have been necessary and it takes a bit of care but it then came out easily. 2. Before replacing the yellow button, test the vacuum first. If you put the yellow button back before testing, you've then got the removal hassle all over again if it's still not working. One of the spade connectors that I hadn't been working on had pulled loose during the rewiring process and, hence the machine didn't at first work. Checking to find where the fault might be was an easy task before everything was reassembled.

Just fixed our dc04 using your method and it works. I salute your work sir

Cracking video followed the instructions and replaced the cable no ptoblem. Took about 15 minutes to do. Thanks very much for sharing saved a trip to thr repair shop

Thanks Alec - successfully followed and money saved. The reconnection/reassembly was a little fiddly and we took a photo of it all before to make sure we got the wires in the right positions so that the on/off switch relocated snuggly.

Thank you Alec. With your instructions, I was able to easily fix this problem in 10 minutes.

Many thanks - even years after you made it !

Exactly the fault on my 04. Searched and your fix came up straight away. Amazing it came from the other side of the world - thanks from "up here" in the cold UK on Christmas eve to you lot "down there" - on a nice hot beach with a cool beer. Thanks lads great video which was straight to the point and easy to follow. Regards Peter

Brilliant thanks I managed to fix it, my wife was threatening to buy a new one so this has saved me a lots of money

Thanks a lot for this video buddy, was able to get my old Dyson back on the go! Haven't got the kind of money they want for a new one nowadays! Many thanks again 👊🏻

Finally I can have a longer cord. No more extension cord connection catching on corners. 15 meters, you beaut. I just ignored/cut the earth cable as it was not needed.

Hi Alec, Brilliant video, very easy to follow and I have saved myself a load of money by fixing my DC04 myself. Thanks for your help - much appreciated.

Thanks so much for this. I've just done this repair on my Dyson with your help - it would have taken me a long time to work out how the get the switch assembly out!

Nice one mate, fixed my DC04 in about half hour, reckon you just saved me a few quid, nice one ta!!!

Hello Alex.hank you for an easy to follow video. Using it I've just fixed my Dyson and can now get on with housework. Thanks again.

Hi Alec, I knew there must be a way! I called the Dyson helpline but they wouldn't help due to it involving the electrics! After watching your video I had it mended in 10 minutes. Many thanks.

Very useful video. Thanks for sharing your knowledge from the UK

perfect instruction - broken wire...now fixed - thank you very much!!!

Thanks for this very clear advice. It worked a treat. Back to clean carpets here in Leeds, West Yorkshire.

Cheers for video,sortet in 15 mins ,plastic green switch broke but so what I'll get another. Again 🇬🇧👍 Jim

Thanks from me, too. Had the same split cable outer, and fixed in ten minutes with your guidance. Great video.

Cheers! Managed to do this really fast thanks to you putting this video up!

You are a life saver mate! Thanks for this 🙂

Great video. Tried to do this once before but couldn't figure out how to remove the switch button. This video was easy to follow.. I have had this fault 4 times now (3 x professionally repaired) so it's great to be able to do it myself.

many thanks alec,fixed in 10 mins,once i could see how to lever the switch out without breaking it!

Great Alec, thanks for the video. No expensive trip to the shops now!

Thanks for this really useful post! Job done! An old DC04 back working in Horsham, West Sussex.

Great video. Fixed in 10 mins

Great video! They charge £25 in the UK for this. Getting the yellow switch off can be a pain, but they only cost a few quid if the worst comes to the worst.

Thanks for this - saved my mother a load of cash and me going insane trying to figure out how you get the switch off!

Brilliant video m8 helped me a lot.. cheers.👍👍👍👍👍👍👍

thank you for this great video

Thank You - clear and concise. :)

@HelpzzHD I use a 2-3mm size connector. As long as the male and female part are a matched pair you will be fine.

Thanks a lot Alec. 👍

Great job.thanks.

I'm looking for 2 of the very small clear plastic connector that is inside the power box at (junction?)hard to find, I don't know what they are called

@HelpzzHD the red things are terminal connectors and spade connectors. Should be able to get them from any electronics store or big hardware place :)

All those replaceable parts. Gotta love dyson. I've had my DC03 for 17 years and hasn't let me down.

Hi Alec, can you provide the same advice (and video) for a DC03? Desperate for your help Thanks Jenny

Hi Alec, great video and I'm going to have a go of this myself. Do those shielded spade connectors need to be a particular size? I'm going to need to buy myself a pack, and I've noticed they come in different sizes. Cheers Paul (Liverpool, UK)

@christiantroy1974 Awesome ! Glad to have helped, Happy Vacuuming :)

Brilliant

Alec, thanks to you my wife thinks I'm a genius.

Ta very much... the screw under the power switch had me stunped...

what vacuum shop you work at

Would it be the same thing for a dc14 ? Thanks for sharing as at the moment everyones trying to economise;)

thank you, you have just saved me £25 pounds by not taking it to a repairers. :-}

legand

Camera's to far away pal