Easily Remove Rust From Your Saws 

Good job buddy. Just bought a used table saw two days ago with a rusty top. I’m going to do what you did and see how it goes. Thanks

Good job. Thanks. There are a lot of "rusty table saw" videos out there. You did a helpful overview for folks like me who need to catch up on maintenance and reduce friction for good clean cuts.

I knew from "wooder" you knew what you were talking about. Thanks

New subscriber here. I was sold with the Saw Stop sticker. That is hilarious! I have a Saw Stop fund going myself. Amazing job you did with removing that rust. Very nice technique. One thing that has always amazed me with people selling table saws on places like Craigslist or Offer Up or other sites, is they don't take the time to remove the rust and dirt and junk collecting on the table saws. I mean if they took a little time fixing them up they would probably get a better price for them.

Good video man. Like the “saw stop” logo and the awesome bike.

Nice job 👍👍👍 I just inherited most of my Dad’s tools and the table saw bandsaw and so on and all the tops looked like yours so thanks for the video it will come in real handy

vinegar with a little bit of dish detergent and a stainless steel pot scrubber works for me. won't rust if you wipe it dry right away because of the residual vinegar.

Best video related so far. Thanks

I've been using fine steel wool. Does a nice job followed by a paste wax for table saws.

Nice video. Looks like you need to do the same thing to your band saw top too. Love it BTW. I have an el cheap o Taiwan band saw that I bought cheap. Put new tires on the wheels and it is serviceable but that's all. Thank you for the video. I appreciate it.

This is going to sound odd but I have had the best luck and fastest results using a wide sharp chisel as the first step. A razor blade works really well too. Dry, no lubricant or liquids. I’ve found that sandpaper, scotchbright pads and especially steel wool takes a very long time and a lot of work especially with a lubricant. The above (minus the lubricant) works excellent after the scraping process but not before. Try it out sometime, you’ll be delighted with the results. So my method is scrape first. Then scotchbright. Then fine steel wool. clean and degrees with naphtha or denatured alcohol. Then paste wax the top, fence, any sliding mating surfaces and sweet Suzy she’s ready to perform!

Good video thank you 🙏

Very nice!!

Fantastic video...

Cool video, I just got a new used tablesaw and bandsaw. I need to clean them up the same. I really like using turtle paste wax on my vehicles, I'm wondering how that would be on the tool tops. I might give it a try.

I got a cheap Skill brand table saw,. That i turned into a SAWSTOP, brand table saw, guys are jealous!

I can’t stop laughing at the SawStop tape sticker. 🤣🤣🤣

What did you use to clean the WD-40 off while you were plugging the gloves?

Hey, brother - get yourself a dehumidifyer...your beautiful band saw is begging for one!

Using a 800 grit wet dry sandpaper with wd 40 works well.

Love it. Only thing is, you used glide coat to clean off the Wd-40?

You can use water as a lubricant so long as you use a liquid to drive off the water. I'm in your camp as it seems pointless when wd-40 makes an extremely effective lubricant for this job

why did e you let your saw get to that rust ?

How was all of it rusty but the channels

What grit sandpaper did you use or reccomend? I just got a mitre saw at a flea market and can use cleaned, thanks in advance 🙂

Thank you. Do you recommend going through the progression when busting the rust or can you go straight to the WD40 and sand paper option? Your "after" picture was remarkable. What do you recommend in terms of maintenance w/ the Bostik? Also, I've seen some videos recommend paste wax for the preservation / lubrication phase. What's your take? Thanks again!

Great video! Would WD-40 Specialist® Corrosion Inhibitor work as well as Boeshield? Curious before I buy or try.

My Saw Stop has storage rust blues too but, mine is worst than this. I might need a new top.

Why show the T9 and not use it?

I use grill blocks: www.google.com/search?client=firefox-b-1-d&q=grill+blocks Takes about 5 minutes.

If you're like me and can't stand the smell of WD-40, use mineral oil, no smell and works just as good.

“Easily” the title says. 🤔 Sped-up video of man doing a lot of hand sanding with penetrating oil.

Send me that Grizzly bandsaw and will clean it, service it and adjust it for you......no charge. Will only take 15 to 20 years...😁 And we all know that's your bike...