Everything you need to know about NMEA2000 | SVB

Подписаться 6 тыс.

Просмотров 105 тыс.

50% 1

Everything you need to know about NMEA2000.
📌 Short description:
The SVB NMEA2000 video tutorial provides an insight into the basics of the latest NMEA network standard It explains how to setup an NMEA2000 network and how to extend it. We hope the tutorial will help you with the installation of NMEA2000 components onboard and show how an NMEA2000 network can be used.
📌 All NMEA2000 products featured in the tutorial are listed here:
- NMEA2000 Micro-C Starter-Kit: www.svb24.com/product/510057
- NMEA2000 Micro-C 4-Way Splitter: www.svb24.com/product/509779
- NMEA2000 Micro-C Dummy Cap Male / inside thread: www.svb24.com/product/510059
- NMEA2000 Micro-C Dummy Cap Female / outside thread: www.svb24.com/product/510060
- AIRMAR DST800 NMEA2000 Through-Hull Transducer: www.svb24.com/product/117356
- B&G NMEA2000 Wind Sensor WS310 incl. 20m Cable: www.svb24.com/product/510490
📌 A large selection of NMEA2000 Mico-C products is available in our online shop: www.svb24.com/category/70348
📌 Further videos:
- What the new radar technologies can do: • Radar on board - Doppl...
- AIS Transponder - Installation with external Splitter: • AIS Transponder - Inst...
- Removing Antifouling: • Removing Antifouling |...
- Applying Antifouling: • Applying Antifouling |...
➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖
👋 Subscribe to our channel to get more tutorials and hints and tips: / @svbteam
📰 Subscribe to our newsletter and never miss any boat news and special offers: www.svb24.com/news-letter
➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖
💡 What is NMEA2000?
The NMEA network protocol was developed in the 1980s by the National Marine Electronics Association, with the aim of creating a uniform standard for data transmission between devices of different types and from different manufacturers. With it, GPS, wind, depth, AIS, speed, engine & compass data can be exchanged between, for example Simrad, Garmin and Raymarine devices. An NMEA2000 interface is required to do so. Images, such as from radar and fishfinder, as well as map content, cannot be transmitted via the NMEA2000 protocol.
💡 NMEA0183 vs. NMEA2000
Compared to the NMEA0183 system, the NMEA2000 network is much easier to install. While NMEA0183 networks involve a relatively cumbersome process of connecting open cable ends using luster terminals, NMEA2000 technology has connectors that can be easily connected using appropriate T-pieces, network cables and multiple distributors.
💡 The 6 fundamental components of every NMEA2000 network
- 1. NMEA2000 Backbone
- 2. NMEA2000 Terminal Resistor
- 3. NMEA2000 Line Cable
- 4. NMEA2000 Power Cable
- 5. NMEA2000 Display
- 6. NMEA2000 Transducers
#NMEA2000 #Network #Tutorial #English

Опубликовано:

19 фев 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 38

@xesusdevila7520 3 года назад

Excellent, concise tutorial. Thanks!

@FinnishPanther 4 года назад

This was brilliant, thank you!

@JimGrady67 3 года назад

Thanks! this is the best and most informative video I have watched on NMEA2000.

@americasailingclub 3 года назад

Great info!

@ke3552 2 месяца назад

Nice work, thanks. Subbed.

@adricspiteri1908 2 года назад

Thanks very much

@asennaydenov6461 3 года назад

Brilliant Thank you! Do you know any other wind transducer then B&G can work. VDO ,Simrad and Garmin.

@tonyebeyer 3 года назад

Great explanation, thank you! A question: Could the wind sensor have been added without adding the last T connector, instead connecting it where the terminator was in the original setup? (Since the wind sensor already has a terminator).

@SVBteam 2 года назад

Hi Tony, you should use an T-Piece to connect the wind sensor to the NMEA2000 network. You can use a dummy cap where normally the resistor will take place to make the network waterproof. www.svb24.com/en/nmea2000-nmea2000-dummy-cap-female-micro-c.html www.svb24.com/en/nmea2000-nmea2000-dummy-cap-male-micro-c.html

@bearingSSW 2 месяца назад

What for are those terminators? Can I switch on power to check if the sensor is working without terminators?

@robertraft 3 года назад

sweet, im taking the classes next week. im stressed. thank you.

@kme8134 3 года назад

Hi, who are you doing the classes through and what qualification is it for? Thanks

@robertraft 3 года назад

@@kme8134 mei basic and advanced classes plus the nmea 2000 class.

@robertraft 3 года назад

@@kme8134 it is through nmea the info is online

@kme8134 3 года назад

@@robertraft Many thanks! I will have a look.

@JohannesNeumeier 4 года назад

Wenn der Windsensor auch als Endstück dient könnte der auch am Backbone-"Arm" angeschlossen werden, oder kommen Sensoren immer an die wegstehende Part des T-Stücks? Also sind die seitlichen und der stehende Anschlüss am T-Stück funktionell unterschiedlich voneinander, oder dient die Konvention lediglich der Klarheit?

@SVBteam 4 года назад

Hallo, um das Netzwerk nach dem NMEA2000 Standard aufzubauen, sollten die Sensoren an den abgehenden Anschluss der T-Stücke angeschlossen werden. Diese Anschlüsse sind in der Regel weiblich, sodass die Geber bzw. die Sensoren über einen männlichen Anschlussstecker verfügen. Die Backboneseite des Netzwerkes verfügt über eine weibliche und eine männliche Seite. Die seitlichen und der weggehende Anschluss der T-Stücke verfügen über die gleiche Pinbelegung welche strom- & datenführende Leitungen beinhaltet.

@benlyons5884 4 года назад

Quick question, why isnt the acronym NEMA if it stands for National Electronics Marine Association, but always referenced as NMEA

@SVBteam 4 года назад

This is a really good question, Ben! You're the first one to notice our technicians little mix up. :-) NMEA stands for National Marine Electronics Association

@nelsongilbert1695 4 года назад

They r your enemy. (N M E)

@AthelstanEngland 3 года назад

Thank you excellent demo. So the two terminators can be anywhere on the network it's not like the old ethernet daisy chains then? PS as you're German I completely excuse the europop music :)

@SVBteam 3 года назад

Hi thank you very much for your comment, it´s recommended to place one terminator at each end of the network. The wind sensor is a special case because it´s in general the part with the major distance to the network/backbone.

@backthebadge4009 4 года назад

How do you know the wind sensor had a terminating resistor?

@SVBteam 4 года назад

Hi, it's usually commonplace for wind transmitters to have a resisitor preinstalled. Some manufacturers provide this information within their manuals.

@04piaci 4 года назад

@@SVBteam What if i want to connect more devices (2 or 3), but all of them have preinstal lterminating resistor ?

@SVBteam 4 года назад

@@04piaci Hi Jozef, according to the NMEA2000 specifications more than two resistors can interrupt the data transfer, so this should be avoided. We know only about windvanes which have an intergrated resistor and your will rarely install more than two windvanes.