Flysky FS GT5 radio setup rear steer, budget crawler 

Thats great! Thankyou for your comment👍

Ooh, well lucky it was a dry stream bed and not a wet one!!!

Thanks. very hopeful.

Excellent, glad its helped a bit

NO WORRIES, I'M GLAD IT HELPED YOU OUT

Thankyou

I just got this radio too, so youre saying I can assign my aws modes to channel 3 or 4 to easily flip through the modes?

Yes its not bad, shock.oil is a bit stiff, but ive weighted the wheels now so should be a bit better again

Thanks mate, if it helps anyone out then thats great, thanks for watching

Glad its been usefull for you and others to watch👍

Yes your right, ive been doing that lately and suggesting that to people who have asked aswell, tbanks for watching my vid!👍

Servo knobs? are talking about the 5-6th channels? also have either of you just turned off the crawler mode and just flipped through the modes using the 3 rd channel?

@Sebastian JAROMI Yes so you can thumb steer the front and steer the rear with 5 or 6

@@shaynejenkins446 Cool!!!!but is it also possible to just turn off the crawl mode and flip through the other modes using the 3rd channel? Or possibly the 4th? Either way thanks for the help from a newbie 🤟👍

@@sebastianj5848 No it wont work that way that I know of. You really want to turn the rear independently though. Sometimes it just needs a tiny turn then back to straight to make a line or get unbound. I use my rear steer like dig. Not a whole lot, only when necessary.

Ah no way!! Thats a great function, thankyou for passing that info on👍

If you turn crawl off the channel 3 button on the remote with switch it back and forth

Thats right, channel 3 supplies a lower link to tve rear servo in order for the radio to talk to the servo, but, the channel 3 "button" is basicaly an on/off switch for that channel. You'll notice that when using ths dial in rhe screen and cycle through when you get to the "off" position the steering just slams to one side as you describe, its because ut cut the signal to the servo. It is a little frustrating i will admit, why that channel "button" canr be used to cycle through the different steering modes i dont know. When i use the all wheel steering i just leave the screen in the options mode and change it as i go. Alternatively something you might like to try is plug your servo plug into , ,, , i think it was channel 5, , , which should be one of the twisty knobs on the top of the radio next to the screen. I found that once i had selected a steering mode, i could now control the rear wheel steering with the twisty knob independantly from the front wheels!!! But the rear steering stays where you set it to, it wont self center. This mode is good whith a bit of practice driving one handed with your thumb to steer, and then controlling tbe rear wheels with your other hand!! Have a play with it and let me know how you get on! Thanks for watching my videos, hope to post some more RC videos soon

Yes rear servo connected to channel 3 and front servo in channel 1, , and your ESC in channel 2. With the crawl modes now you should be able to access the different steering modes. Is it working for you?

At time stamp 13:20 is a section on the crawl modes

@@sub9sec Sorry for my late reply!! Thank you so much, got it!!!!!!!

@@Bidle78 excellent

Hiya, channel 1 is for front steering Ch 2 is for throttle And ch3 is for your rear steer, hope that helps you out

@@sub9sec yes, thank u very much.

Hi Simon, good question, i have no idea! Maybe i'll give it a try and see if it will link up to something else

Interresting, i'll be honest i havent tryed running independant lights off the other channels yet but thought about it the other dsy. I will do some experimenting on that soon for you and see what the answer is

You have to have a on of box to run the other channels to turn them on and off

What are you saying what box

Ah interresting

4:14 in this actual video shows how to reverse the steering👍

Rear steer servo? Ive got that plugged into channel 3 if i remember rightly

@@sub9sec thank you...