FTX Hi Rock Lights & flysky fs gt5 light channels 

I feel I can help here, the Receiver pins are - + s . So Negative / Pos / Signal, as you say in the vid Ad. The Neg and Pos pins on the RX are all on a Bus (just all in one line)- they are all connected to either Neg or Pos, and the Neg ones all go to the BEC- and Pos ones all go to the BEC+. (Batt Eliminator Circuit) So power available on this bus is what the Esc's BEC puts out to it through the Esc's RX wire/plug. So you can't draw more than it can supply. ( It may only be 3A), so don't run too many lights off it, because the servo's are also sharing this power. If you're running High power steering servo's (Two in Ads case ) you may need a separate BEC to supply 5v+ more Amps to the servo's, otherwise if both servo's stall out while driving - the BEC on the Esc will smoke. You need a BEC that can supply the servo's Amp draw at stall. I will post a link to the items I mention here at the end. The two LED's when you reversed that plug Ad are so low a current draw that they were coming on using the signal line! , if you slow-mow video that, they would be flashing with the signal of the RX !. So you will smoke the RX with anything bigger there, so only plug them in the right way around. Your spot on with the Light Bar - it has a chip in it that is reading the signal from the channel you were adjusting, and so you were able to control the various modes that it has by adjusting the channels output. Plugging an RX plug in backwards should generally be avoided, I damaged an Esc and RX at the same time doing this. So to switch them two wire LED's on/off with the channel you would need something like this;- (Plugs into the controlling channel and then the lights plug into it. hobbyking.com/en_us/dr-mad-thrust-electronic-onoff-switch.html?queryID=286dd563ba202f21a486334df0183c56&objectID=83129&indexName=hbk_live_magento_en_us_products And a BEC which can supply 3Amps (runs directly off the Main Lipo) example :- (You may need a bigger BEC if you need more Amps etc.) hobbyking.com/en_us/kingkong-5v-3a-ubec.html?queryID=17ab546e4967f7cbeec7ea4f2d9dd299&objectID=20575&indexName=hbk_live_magento_en_us_products Hope this helps Guys! . Matt

Great video, helped me with understanding my current lighting dilemma. Channel 4 seems best option. Thanks sooo much!!

Gustavo fring 😂 that's the dude from breaking bad

Set your end points on 3rd channel and it will work. Just had this issue then it will work on the clicker

Great video. Been having an issue with a new set of color changing leds i just bought. You may have shown me the fix I need! I'll have to try when I get home. Knew I should have brought my truck to work haha! Cheers!

I only watched because I admire your beard. Kidding mate, great vid. Cheers!

I just got a light bar and it's all part of the programming in the light bar 2 presses on channel 3 sets the color, a long press turns it off and a long press turns it on

Awesome to investigate 👍

you can get a led controller that will let u turn on off from remote for about 5 dollars off ebay. goes between led and rx

I got reciver switch for lights, than I can use buttons on controller to use any stuff like winch, lights or any other even with two stages like brightness

Can you help me on the same radio when I'm in reverse I have more power than forward how do I fix the problem when I go to rev it just switch it on the radio how do I problem gram it in reverse mode to get full throttle thanks

Did anybody point out, Gustavo Fring is a bad guy from Breaking Bad?

I have a red white black wire's on my lights no matter the way I plug it in it stay on the 3 wire's go into 2 wire's that could be the problem