Flysky i6X FIRMWARE Update Guide for Beginners 

There is a way to get 10 channels from this receiver through ibus. You can find videos on RU-vid

So you mean that OpenTx is not a good firmware? I haven't tried that yet. Can you give your remarks about it?

​@@AKElectroDIY você poderia deixar o link dessa última atualização desse software . Oque eu uso no meu rádio é atualização de 2014 , teria como você deixar o link pra nois baixar esse software? 🤝🏻

​@@giramundo.You can just visit the official flysky website. Its available there.

@@AKElectroDIY muito obrigado amigo , somos apaixonado por o hobby aqui somos aero modelista 🤝🏻 valeu , continua com o conteúdo informativo é muito bom 👍🏻

​@@giramundo.I'm glad you liked the content. Cheers 🎉

Hi there! It sounds like you're having trouble with your transmitter not showing up in Betaflight. Here are some steps to troubleshoot this issue: 1. Make sure your receiver (FLI14+ in this case) is properly connected to your flight controller. 2. Check the Betaflight configuration for the correct UART port and receiver protocol settings. Ensure that it matches your FLI14+ receiver. 3. Verify that your transmitter is powered on and bound to the receiver. Double-check the binding process if needed. 4. Ensure that your transmitter is set to the correct model/profile that matches your Mabula 8 drone. 5. In Betaflight, check the Receiver tab to see if any input is registering when you move the sticks on your transmitter. If not, there might be a configuration issue. 6. You can also try re-flashing the firmware on your flight controller and receiver, as sometimes a firmware mismatch can cause communication issues. If you've tried these steps and are still facing issues, please provide more details about your setup, and I'll do my best to assist you further. Good luck!"

@AKElectroDIY thank you soon much for the reply... turns out my flight controller did not support ibus so I switched it to sbus and made sure my serial uart was correct , and bam! my transmitter started to show up in betaflight. got it all sorted out after a 2 day struggle :) thanks though ! 👍

This is just a tutorial to update your firmware for beginners. In the same way, you can also upgrade to opentx or come back to original one

Yes that’s what I did I went back to the og ..usb joystick don’t work with open tx on so for all the beginners why update to open tx and then can’t use your simulator and having to deal with transmiter loose setting regular with open tx wish all that time

You have to select 10 channels from aux channels setup. Then if you go to display channels, you will need to press down key to scroll down to see the next 4 channels

​@@AKElectroDIYThank you very much. Everything worked.

@@vanyaleskk1748 Glad it worked

I don't think so. Generally, they are not deleted.

Maybe the transmitter drivers not yet installed on the computer. Check if it shows up in Control Panel > Devices and Printers

@@AKElectroDIY The transmitter shows in the device and was use in simulation program already.

Then might me the firmware software issue. Turn off your antivirus and download it again.

Yes, it will support all 10 channels for flysky i6x.

Sorry to hear that. How can I help you?

If you have 6 channels, then upgrading to new firmware will give you 10 channels. But if you already have 10 channels then its not necessary.

It gives range of 800 to 1500 meters while flying a drone. I will soon make a practical video to test the range of this transmitter.

@@AKElectroDIY does I have to connect a radio module to get a range of 800 to 1500 metres or its directly without module ,it's direct via remote

@princerozario9788 It is the own range of transmitter without any external module. Means direct range between transmitter and receiver is 800 to 1500 meters in open area

@@AKElectroDIY but I have a problem I get only a range of 100 metres don't know why

@@AKElectroDIY which receiver do you use

You get 10 channels if you previously have 6 channels. There might be some other changes but they are negligible.

@@AKElectroDIY i have V1 2018 i have allready 10 channel

thanks but I read they is some virus on some update I dont want risk that

@@AKElectroDIY i looking for put an alarm when the signal is too far of tx

@@did3d523 There is already a low signal alarm in it. If you don't have this feature, then consider upgrading to newer firmware. If you install from the official flysky website then there should be no risk.