Flywing H1 Setup Tutorial & Tips

Подписаться 54 тыс.

Просмотров 87 тыс.

50% 1

Flywing H1 setup tutorial to help you understand and configure your Fly Wing H1 GPS autopilot system.
Video Time Chapters:
0:00 What tools & resources you'll need
0:34 Helicopter mounting & powering considerations for the H1 Autopilot system
3:24 Downloading the software and driver from Flywing's website
4:20 The H1 setup assistant, USB connectivity, channel mapping & radio configuration
13:12 Swashplate setup & leveling, collective range, tail rotor setup
24:30 Gains, throttle output, agility, GPS settings, etc
29:01 Magnetometer calibration
29:57 First test flight
Useful Links:
1. Fly Wing H1 RC Helicopter GPS Flight Control System 45cm GPS wire:
www.banggood.com/custlink/3vv...
2. Fly Wing H1 RC Helicopter GPS Flight Control System 13cm GPS wire:
www.banggood.com/custlink/33K...
3. Fly Wing RC Software & Instructions download page:
www.flywingrc.com/en/software...
4. My Fly Wing H1 Autopilot Review:
• Fly Wing H1 Autopilot ...
5. My Swashplate Setup, Leveling & FBL Configuration eBook:
www.rchelicopterfun.com/swash...
6. Learn more about RC Helicopter Tools:
www.rchelicopterfun.com/rc-he...
7. My tail rotor setup tutorial video:
• RC Helicopter Tail Rot...
PLEASE READ THE FOLLOWING! I WILL NOT RESPOND TO THESE COMON FLYWING H1 QUESTIONS THAT ARE COVERED BELOW:
- What FrSky S-Bus receiver are you using with the H1? Answer: X4R-SB
- What is DMA Collective? Answer: It's collective to tail rotor pre-compensation mixing.
- Will the Flywing H1 work with a Spektrum/JR DSM2/X Radio? Answer: Yes with a Spektrum DSM RX that has an S-Bus protocol output. I believe the aftermarket has a couple but I don't fly Speky anymore so I'm out of their RX loop. I've also heard of Spektrum DSM to S-Bus converters. Use your Google Fu!
- What other radio systems will the H1 work with? Answer: Again, connectivity functionality with the H1 like any flybarless system or flight controller is not radio brand/ RF protocol dependent, it's receiver dependent (i.e. the receiver has an output protocol that the H1 is compatible with). Any 8 channel or better receiver (need 9 channels for full functionality of the H1) that has an S-Bus protocol output port should work. You also need a computerized 8 or more channel radio/transmitter (9 channels for full functionality).
- Were you able to get rid of the cyclic pitch oscillation from the review video? Answer: Yes, but it's a compromised gain setting (either flies well in GPS mode or in 3D mode, not both). Experiment with your gains. Fly Wing at minimum MUST separate the two axis of cyclic gain to give us better tuneability. This is a helicopter after all with different mass and inertia components along the roll and pitch axis, not a simple quadcopter.
Of course, try the usual RC helicopter pitch bobbing fixes as well that work with all collective pitch RC helicopter such as softer head dampening, higher head speeds, ensuring CG is bang on, or loosen blade bolts slightly for easier blade lead/lag.
- Even though I cover this in detail in the video as do the instructions, I'm still getting questions on channel mapping order. The H1 uses Futaba's channel mapping. CH1 Aileron, CH2 Elevator, CH3 Throttle (collective function for the H1), and CH4 Tail Rotor. No, this order can't be changed within the unit. You also need two, 3 position toggles you can assign CHs 5 & 8 to, and two, 2 position toggles to assign CH's 7 & 9 to. Channel 6 IS NOT USED.
- So it only works with HV servos? Answer: NO. That's the best "plug and play" option but not the only option. Anyone in the hobby should know there are several ways to power servos at lower voltages independent of the receiver's/FBL/control unit's input voltage. Installing rectifying diodes such as HER 503 in series to each servo's power input lead for example would be the least expensive. This will drop the input voltage to the servo by about 0.6 to 1.0 volts (load dependent). We have been doing this for years after all when powering 4.8V tail specific servos in 6V power systems. Use your Google Fu to find other servo voltage regulation methods that may be better suited to your particular setup. Of course if you have HV servos or thinking of upgrading to HV servos, that is by far the best option.
- Can you perform the automatic circle & figure 8 function when inverted in GSP autopilot mode? Answer: NO! The H1 will lose collective & or cyclic control of the helicopter if you activate the circle or figure 8 while inverted. I almost crashed why trying this & Fly Wing has also confirmed this.
- What radio/transmitter are you using in this video? Answer: FrSky Horus X12S with OpenTX operating system.
If you still have questions regarding the Fly Wing H1 system, contact Flywing directly or one of their dealers - I AM NOT FLYWING TECH SUPPORT!
Please consider giving a thumbs up & subscribe if you enjoy my content - thank you.

Авто/Мото

Опубликовано:

3 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 344

@Rchelicopterfun 4 года назад

Fly Wing H1 GPS Autopilot Full Review Video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-taNEI680-68.html Fly Wing H1 Flybarless Autopilot System: www.banggood.com/custlink/vv3hYQu3g8 Learn more about the wonderful & fascinating hobby of RC helicopters: www.rchelicopterfun.com/

@jerrylachlan4059 2 года назад

Instablaster

@larrychamel 4 года назад

Another Great video John! Thanks for sharing your passion and knowledge with us. Your videos are always Fantastic and everything is covered, no loose ends as you never leave us hanging. You always cover any questions we may have!

@Rchelicopterfun 4 года назад

My pleasure

@jamesrooks9284 3 года назад

Very informative and helpful in a no-nonsense style of instruction. I have an H1 on the way to install on a trex 470l. This answered many questions for me. Thanks!

@Rchelicopterfun 3 года назад

Glad it helped

@ace-gc5xm 4 года назад

showing the head leaving is also very helpful thanks!

@johnclarke254 4 года назад

Great video, many thanks. I have just received my H1.

@Rchelicopterfun 4 года назад

Enjoy it

@RCredman69 4 года назад

Thnx, for the set-up video, John. 👍

@Rchelicopterfun 4 года назад

You bet

@ElecTrev 4 года назад

Thanks John, this will be really useful when my H1 gets off the slow boat

@Rchelicopterfun 4 года назад

Glad to help

@1948bluesman 3 года назад

great video,got me through the setup super quick,thank you.

@Rchelicopterfun 3 года назад

Glad it helped

@michaeldomanski2472 Год назад

I just got the FLY WING Huey UH-1 and right out of the box I got a GPS Connection Exception error (constant blinking red light). Support told me I need to calibrate the compass which i did successfully many times. I ordered a new FlyWing H1 FC GPS Long Wire which should remedy the problem. Great eye opening video presented in a professional educational format. UPDATE: Replacement GPS module installed, recalibrated and flys like good in GPS. When switching from GPS mode to 3D, the Heli descends, so I have to push up on the collective past center, need to figure out how to tune that and I'll have a good heli.

@alishanmao 4 года назад

Thank you for the video. i am just way too busy to do this. i have a new KDS Innova 550 complete combo sitting at home but I can't find time to build and setup with H1.

@themusichallacademy2787 4 года назад

Thanks for the complete details setup video.

@Rchelicopterfun 4 года назад

You bet

@themusichallacademy2787 4 года назад

Hi John, thanks again. I was about to return this H1, I thought it's a crap! Lol. Now I'd setup everything as you did. Going for the test flight once rains stop. 😎

@jrb8081 3 года назад

This would be good for someone that would like you said lost their ability to fly, Thanks for your video's.

@RumahkreatifKalibasau 3 года назад

Nice for sharing men. Thank you

@matthias3771 3 года назад

thanks for the great tutorial!!

@Rchelicopterfun 3 года назад

Glad you found it useful 🙂

@djlouis2150 2 года назад

Well done mate

@stefano131978 4 года назад

thank you very much

@mohdnihal1638 4 года назад

Thanks bro

@Rchelicopterfun 4 года назад

Welcome

@user-ry1mw7tn6h Год назад

H 1 素晴らしいです😉✌️

@Rchelicopterfun Год назад

👍🙂

@user-ry1mw7tn6h Год назад

@@Rchelicopterfun 返信ありがとうございます😉✌️

@lancedeejay 3 года назад

I just talk about rc stuff and my fam and girl think it’s for kids. They should watch this vid. 😎

@wawanlost6502 3 года назад

Mantap

@bobbylana 5 месяцев назад

Thank you very much! I`ve had issues with my older Microbeast Plus after updating to the latest firmware which made the FBL system totally malfunction with the update. Looking for a replacement FBL, you help me make a decision on the H1 controller, this is the one to buy.

@amiraldz1970 3 года назад

waiting for a route programming video thanks

@Rchelicopterfun 3 года назад

You'll be waiting a long time since the H1 doesn't support GPS route planning - thank goodness. May as well write the final epitaph to our hobby the day powerful and dangerous collective pitch RC helicopters are flying autonomous GPS routes with no pilot input. It's bad enough mindless drones are capable of that.

@rogerf4430 Месяц назад

Great video thanks from the uk. I think I’m just about to order one. I use microbeast which I can set up in 5 minutes without a pc but I want to learn inverted btw. Cheers

@Rchelicopterfun Месяц назад

Sorry, but the H1 won't teach anyone how to fly inverted. It will only make your regular flying worse. Stick with the Beast (it flies much better than the H1 ever will), and learn your inverted orientations, first on the simulator and then apply those skills out at the field. I cover inverted progression skills (actually Bert does) on day 11 "How to Fly Helicopter Aerobatics in the flight school section of my website: www.rchelicopterfun.com/how-to-fly-3d-helicopter.html If you need electronic help aids, then get a FBL system that has inverted rescue auto-level such as the Ikon. The H1 won't work as a rescue system, it will likely crash.

@ian4012 3 года назад

Another great video John..Thank you. Is it possible for you to make a video on setting the H1 up using Spektrum?

@Rchelicopterfun 3 года назад

I don't fly Spektrum anymore. Setup would be the same however. Set the channel outputs & directions to produce the required inputs in the setup wizard, teach the wizard the channel throws and centering points & store them, follow the setup steps in the wizard to the letter, double & triple check, go flying. 🙂

@gypsyman012 Год назад

Thanks to this tutorial i have setup my H1 on a Trex 500 how ever i can't get the invert switch to function i am using a Frsky X20S everything else works. Thanks for the video

@peterkonrad4364 3 года назад

what I would need is a function to set up a box on my flying field, where the heli can't leave the box. so the H1 would detect if the heli is about to leave the box and then take over control to stop it from leaving the box. especially of course when it is about to hit the ground. I know that the altimeter has some inaccuracies due to varying air pressure, but a tolerance of 3 meters or so would be enough for me. and then when the heli is saved, in the box at a safe height, you can take over control again. man that would be so handy.

@dd0uble 4 года назад

Hi John Salt. The video is awesome, a step-by-step instructions. The best I've ever seen thus far. I just received my H1 unit. And I noticed mine is different from yours most of my writing is in Chinese. And my GPS cable is short, not long like yours. Where exactly can I get you're one from I would love to use that unit on my other helis with the long GPS cord..

@Rchelicopterfun 4 года назад

I have a link to the exact unit I got in the description.

@denisfranck999 3 года назад

I did all what you said but the helicopter doesn't want to take off anymore it's a 450 thank you for helping me

@scatteredparts296 3 года назад

Thanks again for a great video! Could you provide a little more detail about battery dimensions ? Thank you.

@Rchelicopterfun 3 года назад

Fully discussed in my build summary of the ALZRC Devil 505 helicopter: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2N39ephs5w8.html

@MegaControltv Год назад

good video! .. I have a t-rex 600e What helicopter I need to chose in the select helicopter config ?

@darrelltardyvideos3645 3 года назад

John, Thanks for the review and setup of the H1-GPS system. I'm a 75 year old kid and haven't flown my Trex 500 esp for several years due to arthritis issues. After your review I purchased a FW 450 v2 helicopter and I'm extremely pleased that I'm back enjoying my hobby. I would like to update my Trex 500 to the H1-GPS system. For mild flying what servos and esc would you recommend. I know the H1-GPS requires a higher voltage of 7.4 vdc. My current system is setup for 5vdc. Any suggestions would be greatly appreciated.

@Rchelicopterfun 3 года назад

Howdy Darrell, Glad to hear this technology has allowed you to get flying again. As I mentioned in the review video, that's the H1's single best attribute. As for your Trex 500ESP, I guess the first question is have you converted it to flybarless already? The H1 like every other FBL system only works with flybarless rotor heads. For powering the H1 and servo recommendations, there are an array of options at your disposal. You can keep the original ESC if you wanted and use an external BEC for example, or a dedicated RX battery. Servos same thing - several workable options to consider depending on what you are using right now along with what receiver you are running along with what radio system. Best to contact me through my website on my contact page ( www.rchelicopterfun.com/contact.html ) for more complex technical topics like this as I rarely see follow up questions in the comments section of RU-vid. But if your 500ESP is still fly-bared, then all that is moot unless you already have or plan to convert it to flybarless.

@CRUZROYHelicopters 3 года назад

i got a new x10s horus, could you show how to setup frsky radio and what type of rx you like for helicopter.....thank

@Mikemesmereyes Год назад

Dear Sir I have set this heli up two different times. Myself once and a heli expert the second time and everything is perfect. Then when we get every thing up to speed and try to lift off the moment it gets light it barrels over to the left. I sure appreciate your help with my issue. Thanking you in advance

@clebermoreira1472 2 года назад

boa tarde John , vi seu setup e me ajudo muito , mas ocorreu um problema instalei em um trex 450 o GPS h1 , e de repente ele para de funcionar vindo a cair o helicóptero , minha dúvida e a alimentacao conforme o manual fala não pode usar bec de 5v , isso procede ? pois acredito que isso que fez meu Heli cair,poderia me tirar está dúvida e parabéns pelo canal muito esclarecedor.

@Cooldrums777 3 года назад

Great video John. I loved two of your books I bought...setup & tips for electric collective pitch rc helicopters and How to build training gear for RC helicopters. Between youtube, flight Sim S/W and your books I have taught myself to build and fly non 3D at an intermediate level. Now I just bought a used Trex 600E flybar chopper. Can I remove the existing gyro and install the H1 on the E600 without buying a flybarless head and run it with the existing flybar? I would only run the H1 in non 3D mode and use it basically as an emergency attitude recovery system while I gain experience on the E600. Eventually I would buy a flybarless head and dip my toe into 3D tricks using the H1 to bail me out of trouble. What do you think?

@Rchelicopterfun 3 года назад

The H1 like almost all FBL units won't work with flybared heads; it must be used with flybarless. Also, the H1 is not a "bail out" or "rescue" unit. It won't work (at least well) in that capacity. If you want rescue, then get a proper FBL unit with that specific function such as an Ikon2, Bavarian Demon Axon, or Spirit.

@djtoribio135 3 года назад

John buena explicación una pregunta hay un video del flywing H1 que la programación con futaba t10j la hacen en modo helicoptero. No entiendo puedes decirme si es normal o mejor en modo avión. Gracias

@jhawk1977 4 года назад

John, great video...were you able to get rid of that tail bounce (from the review video) by reducing the gain on the parameters page? If so, what did you set it to?

@Rchelicopterfun 4 года назад

Yes, I covered that at the end of the review video including what my final settings were. Those final gain settings I show at the end of that video are of course specific to this particular heli, the mass of the heli, the blade spinning mass, and the particular head speed I'm running. Lots of variables involved when tuning the gain values on any FBL system. As I said at the end of the review video, my final settings were a compromise. I can get it to fly well in 3D mode or GPS mode but not both. Without the ability separate the cyclic pitch & roll axis gain settings, or even better, separate them and allow access to the individual PID gains, I think the best we can hope for is a compromise seeing the setup wizard is also a compromise in the limited adjustability is allows. That or set it up for one or the other.

@armiestone 3 года назад

Thanks for the intensive review, in your earlier review of this item you said it could be implemented on a gas powered helicopter but I don't see how that is possible since there's no input for governor sensor for a stabilized throttle control , or do you think otherwise?

@Rchelicopterfun 3 года назад

Many gas and nitro helis use stand alone governors to control the throttle servo (such as the Futaba GV-1 governor). All that is required is a fixed throttle PWM signal output which the H1 has. Also, you don't necessarily need a governor at all on nitro or gas. We flew them for years without such technology by using creative throttle servo to carburetor linkage arm geometry before computerized radios gave us the power of throttle curves which worked much better. Of course, the H1 gives no such ability with only two single fixed throttle output signals and would have serious limitations when used with IC. In the review, I was merely stating the H1 specs which indicate its compatibility with nitro. I would certainly not condone ever using the H1 with any fuel powered heli nor do I think it would work well for the reasons I just mentioned. Who knows if the H1 can even handle the high vibration environment of a nitro or gasser? That would be another big concern. Again, I was just stating the specs in the manual when I mentioned it worked with nitro. In theory it will, but in practice I would personally never install it on a large fuel powered machine. Moreover, it's bad enough that people with no collective pitch flying skills can take to the sky with this thing on an electric. The last thing our hobby needs is a bunch of fuel powered helicopters being flown by people who don't know what they are doing. Good bye hobby.

@CRUZROYHelicopters 3 года назад

can you show how to setup frsky radio to helicopters, nothing on fros on X10s

@ameersak 3 года назад

after connecting orange R920X for connecting to spektrum. do i need to connect any other satellite reciver in SAT 1? coz in joystick stroke calibration is disabled and says RX NO SIGNAL.

@rmiklosh 8 месяцев назад

Hi John. Can I go thru setup without a wire to my spektrum 8000 receiver which has a satelite receiver (a special plug that I am waiting for to arrive)? From my understanding I will throw out 8000 and just use satelite receiver which is a part of this package?

@airober 3 года назад

Thank you very much John for this excellent tutorial I have a couple of questions. In the initial configuration of the radio control, do you select heli or airplane? and if you select heli is h1? another question. Do you need a 9 channel receiver to program the invert? And the last, dual rates, throttle curve and pitch curve must not be configured on the radio control? Thank you for your help

@Rchelicopterfun 3 года назад

Every single question you asked here is answered in the video and in the manual.

@nickdean468 2 года назад

I have a question John when doing the tail did you end up reversing left tail stick tail or left tail right stick

@vuesduhaut9148 2 месяца назад

Hi Can you help Have you the paramètres for Trex 600 The swash exp And the swash gain Thank you very much

@ameersak 3 года назад

hi john, please let me know why the throttle stick movements are not recognized. the H1 is still blinking red. it should be solid to purple right? but its not. i am now using orange receiver as stated by some.

@TomaAerea 2 года назад

I need help ... my H1 With GPS I can no t connect to the computer and recover at the same time..

@edwinonate1164 Год назад

Hi. I am using DX9 transmitter. Everything is setup properly except that I can't seem to activate my channels 8 and 9 for circle/figure eight and inverted flight. Will you be able to give me advice on these. Thank you.

@Art-ny8uc 10 месяцев назад

after connecting everything to the h1 heli all servo's they make a very strange sound and i can't control them. what could it be caused by?

@hermankoji 3 года назад

last one john and thx. have you chk the swash plate before flying if level up when you tilt forward or sideward by hand. its hard to tell on gps mode except 3d mode and tail response.

@MegaControltv 2 года назад

Hi now I can conect and config with mi laptop , but I think the tail gyro is wrong, because correct to wrong side... with my helicopter is on, and I can full control with my radio, when take the helicopter with my hands and turn tu righ, the tail nove to the right side, then I turn the heli to de left, the tail move to left. I think that is a problem... should correct to the opposite side so that it can counteract the turning force of the main rotor

@timothykay9196 3 года назад

Thanks John, Very helpful video. I am trying the H1 in a trex 450l. I am to the point where I arm the heli, I get the blinking green light. When I throw motor switch nothing happens. I sure would appreciate any suggestions you might have. I know motor and ecs are good bypassing the H1 and just using tx and receiver. Thanks

@andersonjuniodossantos1146 3 года назад

I also have this problem! I can't solve it, could someone help? thanks!

@stefaanbolle6572 4 года назад

Another excellent piece of information you're sharing John! A quick question, is it complex to use the H1 with a 9CH Spektrum radio?

@Rchelicopterfun 4 года назад

No idea if you could get it to work with a Spektrum TX. It would require programming in some creative mixes since Spektrum doesn't use Futaba's channel mapping which I mention in the video is very specific. Moreover, the H1 unit only works with S-Bus RX input and one or two PPM protocols (Spektrum is not listed). I think there are some aftermarket DSM2/X protocol RX's with S-Bus output, but since I don't fly Spektrum anymore, I'm out of the loop. Perhaps Speky does have some newer DSMX RX's with S-bus output?

@stefaanbolle6572 4 года назад

@@Rchelicopterfun Thanks, much appreciated!

@user-if7fi6ip6m 4 года назад

DMA Collective is: Advance compensation of collective pitch to tail

@Rchelicopterfun 4 года назад

Thanks so much.

@jhawk1977 4 года назад

@@Rchelicopterfun so, what does this mean? How will adjusting this from zero affect flight controls?

@Rchelicopterfun 4 года назад

It mixes in some tail rotor pitch to counter main rotor torque the moment the collective is increased to help the tail gyro out so it doesn't have to play catch up as much when moderate to large collective torque spikes hit. It's generally called something like torque compensation, collective pre-compensation, or tail pitch pre-comp on most FBL systems. I've never seen it referenced as DMA, thus the confusion I had. DTA would make more sense (dynamic torque assist). In GPS mode it's not needed at all since the collective response is so slow and tame so there are no drastic main rotor torque spikes created. You only need collective/tail torque precomp when introducing sudden and large collective pitch changes. If you did dial it in or too much of it, you would likely notice the tail kick out slightly in the opposite direction of main rotor torque every time you gave sudden and high amplitude collective commands.

@stefano131978 4 года назад

so you say (that you know) that I could also connect spektrum (dsm / dsmx protocol). Thanks again

@Rchelicopterfun 4 года назад

No, I said no such thing. I said to CHECK the MANUAL to see what RX outputs will work with it. I know for 100% certainty it works with S-bus since that's how I have mine hooked up as per the manual. I have no idea if a Spektrum's satellite RX's PPM signal would be compatible or not. I would venture to say it isn't since DSM is not mentioned anywhere in the manual, but that is just an educated guess. Of course If you have a DSM2/X RX that has an S-bus output (I'm not a Spektrum user anymore, but I think some of their newer RX's have an S-bus output port & some aftermarket ones), then that would work. Best to contact Fly Wing with compatibility questions like this - I can only relay what is stated in the manual and what is working in my application... S-bus.

@maverickgyrocopter2837 Год назад

Does this controller recognize rx Tbs crossfire? good night

@bobsalvesen2070 2 года назад

Hey john...great video and informative....Just now thinking of buying two of these H1's. I want place H1 in a 500X Align and a XL power 550. Do I need to readjust my ESC for voltage output . The BEC output voltage should be to 7.2V. and other question is the Aircraft title should be normal airplane or helicopter. Not good with this technology stuff. Still learning? Thanx a lot

@RCREVIEWS101 8 месяцев назад

at 6:07, when you powered the radio controler you must have "plugged the battery to the system" as the H-1 with USB feed in only cannot send enough voltage to power the Receiver.

@Rchelicopterfun 8 месяцев назад

Nope, powered with USB only

@fernandobertuccelli1856 3 года назад

donde conseguiste el cable del gps tan largo? tu lo alargaste?

@MegaControltv 2 года назад

Puedes compartir fotos de las conexiones… no consigo que mi h1 funcione aún … el receptor no recibe energía y por ende no hay control de radio

@davidjacobs8558 9 месяцев назад

for some reason Windows 11 reports virus infection when I try to download Flywing H1 software from their web site. Cand Flywing H1 be used for counter clockwise rotating main rotor also?

@skrub6969 2 года назад

Love the videos and very informative, question I have for you is what RX are you using? I have a Archer R6 and trying to get it to work with this system and I'm using a Tandem X20S radio. If or what RX do you recommend for this setup on my Algin 450L? All help or info would be great.

@Rchelicopterfun 2 года назад

All in the description

@andreauomogatto7504 2 года назад

Scusami John, non riesco a capire una cosa durante questo video: ho fatto caso quando sposti l'interruttore per metterlo in modalità gps, non riesco a capire che è quella cosa che parla, se è il telecomando oppure il telefono? Cordiali saluti da Andrea.

@JuanSpeedAudio1 3 года назад

👏🏼👏🏼👏🏼👏🏼👍

@bobsalvesen2070 2 года назад

John great video I have a problem with max an min pitch I can't get the numbers the same no matter what I do. Max pitch I get 12 NP but at Min only 8.5 what can I do to fix and what reason is it. And one servo I have to change to reverse that doesn't matter does it?

@Rchelicopterfun 2 года назад

Hi Bob, No idea without seeing it in person - too many variables. Most likely poor mechanical setup, but that is just a presumption.

@iriquiosgunship Год назад

I hope yoi are still monitoring this thread. Thank you for all the variable information that you have shared with us here. When you set your swash plate, do you do that at half throttle? Thank you.

@Rchelicopterfun Год назад

Not sure what you mean by "set your swash plate". Set it to what? Your cyclic pitch range, collective pitch range or leveling it? If it's leveling you're referencing, as with all collective pitch helicopters and as shown in the video, it's leveled mechanically at mid point on the pitch curve. It has nothing to do with throttle output. With that said, the H1 setup wizard automatically sets the collective output to all swash servos at mid value (1500 micro seconds) so collective channel output value on the radio is not important at that step since the H1 overrides it. If your question was not related to leveling, please contact me on my website with technical questions like this since YT comment section is a poor medium for sorting technical issues and I rarely see second posted questions whereas I always see every email question and follow ups on my website: www.rchelicopterfun.com/

@iriquiosgunship Год назад

@John Salt thank you. You actually answered my question (your answer covered pretty much everything). I'm sorry I'm new at this, but your channel is very helpful to newbies. Thanks again.

@donjohnson3375 2 года назад

Hi John love your videos and books i bought you have taught me so much. I fly outside of town no internet wi-fi how do you calibrate GPS compass with no internet fly wing has a video showing how to do it but they are obviously connected to internet on video. I have arthritis in my hands thats why i bought bell 206 scale with H1 GPS FLIGHT CONTROLLER do you think i would have to buy a hotspot and pay for data plan to calibrate Thanks Don j PS started flying 1992 no internet had mechanical gyros

@Rchelicopterfun 2 года назад

@Don Johnson - You don't have to be connected to the internet when performing the calibration, only that you have the setup wizard loaded on your laptop.

@donjohnson3375 2 года назад

@@Rchelicopterfun copy thats a big 10-4 thanks john i really appreciate your help

@MrCADU267 2 года назад

good night john! I have an H1 flywing system, this one. i installed it on my helicopter, but when i turn off the engine cut key it still runs reading. would you know how to inform me of the problem? please . I no longer know what to do. I don't understand anything about the H1 flywing. and Thank you if the case read

@TheScottsatisfaction 3 года назад

Interested in buying a new 800 size helicopter and new controller. Would you be interested in doing a complete setup to bring it to a RTF ?

@bobsalvesen2070 Год назад

Hi John I like your video ...Don't know many times I watched it BUT I bought 2 H1 one for 470 and a 500X. Now I can't get them into the program which I think is due to orange 720 I have a DX9 radio and can't find any 9 ch Sbus made for spektrum any ideas of brand receivers I can use?

@atoadinthehole 2 года назад

Great video and super cool product. I have a NX8 and I know they have 10 mixing channels. Will the Fly Wing H1 work with it using an orange 9 channel receiver? I want to put it in my Align 470LM. Thanks for any advice/guidance you can give.

@Rchelicopterfun 2 года назад

I discuss RX compatibility in the video description box along with all the other common H1 questions.

@blackele4481 3 года назад

Thank you John for the detailed tutorial, much appreciated. I am a newbie to Heli RC. Can I use Radiomaster TX16s with Fly Wing H1 GPS?

@Rchelicopterfun 3 года назад

Learn to fly a collective pitch RC helicopter correctly - don't rely on one of these GPS no skill autopilot things, you'll have way more fun & lasting engagement in the hobby if you are actually flying. But to answer your question, yes, provided you use a 9 channel receiver with S-Bus or PPM output.

@blackele4481 3 года назад

@@Rchelicopterfun Thank you for your kind advice about how to handle my current situation. I will start with simulator.

@ian4012 3 года назад

Hi John let me start by saying hello from the UK and a big thanks for your videos. I will be doing the same build when the kit and H1 arrives, so your videos will be very helpful. Do i need to worry about programming the esc when installing/using the H1? Thanks again.

@Rchelicopterfun 3 года назад

Depends on how you have your ESC setup. The H1 as you know only provides two throttle output levels, off (0%) and on (adjustable % output via the setup wizard). If your ESC is setup for linear throttle response then it's likely okay. If you are running some sort of governor function, then you may need match the ESC governor throttle signal % to the H1 output. I run my ESC on this heli in linear mode (no governor).

@ian4012 3 года назад

@@Rchelicopterfun Thank you John...still waiting for the goods to arrive....sigh

@stefano131978 4 года назад

thanks for the video. great !! I have an 8 channel radio. which function will i not be able to use with only 8 channels? thank you

@Rchelicopterfun 4 года назад

Invert

@cesarlaihee7044 3 года назад

Nice tutorial video. I can I use my jr 11X radio on flywing h1? And orange r920x receiver.

@Rchelicopterfun 3 года назад

As I state, you need an S-Bus signal output from the RX. I don't know a thing about the R920X; if has an S-Bus output it will work, if it doesn't it won't.

@andreklijn878 4 года назад

Thanks 👍

@Rchelicopterfun 4 года назад

Welcome 👍

@tavila72 3 года назад

Hi John. Was wondering if you have ever done a video tutorial on setting up Open TX with an Ikon flybarless controller. I have a RadioMaster TX16S and an Ikon Mini2 that I'm trying to set up on my Oxy2 Sport. Take Care

@Rchelicopterfun 3 года назад

I cover the basics in my swash ebook, but even better is to follow the IKON FBL setup wizard to the letter. It takes you by the hand and walks you through the entire process from start to finish. In the past decade of of setting up FLB systems now, there is no substitute better than the setup wizards in my opinion. They make the process simple and fairly goof proof.

@raulmayoral6861 3 года назад

Thank you John for the help and advice you’ve provided. Since I fly JR still I didn’t have SBUS or PPM available until I located. Spektrum AR7700 Rx which has PPM output. Today everything went fine with the setup UNTIL my buddy and I realized that when we applied elevator the collective calibration display responded. I’m not sure how to fix that until I can buy the same FrSky radio system you use in a few months. Any fixes you can recommend in the meantime or am I dead in the water until then? Thanks in advance!!

@Rchelicopterfun 3 года назад

Good to know about the AR7700 as a working RX option. I'll add that important info in the description for other JR/Speky DSM users. As for the elevator/collective issue. Yes, that's exactly what one would expect since as I mentioned, the H1 uses Futaba channel mapping (AETR) not JR/Spektrum mapping (TAER). Should be able to sort it with some creative mix programming.

@raulmayoral6861 3 года назад

Thank you John. If I find the solution for my problem I will let you know. We appreciate you!

@xanti95 2 года назад

@@raulmayoral6861 Hi: I have a JR radio and I have the same problem of mapping between Collective and Elevator. Did you solve it? Thanks

@CUSTERDCREAM Год назад

Hi John . Great instructional video . I fly a Roban 600 EC145 ( T-Rex 550x mechanics ) thanks to your tutorial it flown a dream first time no issues I just followed your instructions. Now I need a little advice for my new build A Roban 700 Apache. Almost there with it but. I’m using a castle edge 160 ESC ( no internal BEC ) and external BEC pro that has two input leads . I know these can and should go into the ESC port of the H1 using a Y splitter but my question is what about the ESC throttle wire , can I ( using another Y splitter ) in essence running parallel to the BEC . Also would I need to disconnect the red wire from the ESC . Hope you can help . Great stuff

@Rchelicopterfun Год назад

Sorry no idea on BEC pro. I use stand alone RX batteries on all my large machines. As far as I know, ESC connectivity would be the same however since there is no BEC in the Castle HV ESCs so you don't have to remove the red wire from the throttle lead. Of course always confirm with Castle's wiring diagram or contact their tech support if you are unsure, in the off chance the 160 is different from the rest. I've only run the 120HV since these big Robans sip current and will rarely pull over 60 amps if you manage your cyclic and collective energy well.

@CUSTERDCREAM Год назад

Thank you John . Very helpful. Top man

@izudindin2679 3 года назад

hello, today I tested h1 gyro..so far all is well ... but when I switch back home, my swashplate helicopter vibrates just like gyro gain is too high ... so how do I setup this swashplate so that it does not vibrate? set on scale in the system..and I flew earlier using trex600 ... help me admin ... tq

@michaeltrager4381 Год назад

Hi John, Thank you for this video on the setup of the H1. I just purchased one to install on a flybarless TREX 500. Do you still use yours and do you know if their software has improved since this product first came out? Also you mentioned something about governor mode. I guess you can only use one gov mode headspeed ( I have a Castle Creations ESC)? The previous FBL unit was a Mikado Mini V-bar and I just wanted to try this out. Thank you, Michael

@Rchelicopterfun Год назад

I didn't use much more than a month before putting a good quality standard FBL unit back on so I have no idea if they have changed the setup software?

@erthfglvggfffffc 3 года назад

You don't need to mix here throttl-pitch? mixing will make the device FlyWing H1?

@estebanfpv 4 года назад

how to configure the radio? I put it in H1 and the tHR curve and the PIT curve as it puts it. Thank you

@Rchelicopterfun 4 года назад

Once again, and as I clearly state in the video & what is stated in the instructions - you DON'T USE PITCH or THROTTLE CURVES. You use a linear output for channel 3 to give a symmetrical +/- collective range (-12 to +12 in the case of this heli). Throttle output is dictated by what is set in the H1 Setup wizard.

@victormadison3719 Год назад

I have the FW450V2.5 and it flew very well with the stock transmitter and receiver. I have converted to run on my Open TX FRSKY x9D+ Taranis with a X8R receiver. I got it to fly in the GPS mode but it bobs forward and backwards pretty badly even in a hover. What adjustments do you suggest to get it to fly smoothly? Thanks - Vic

@Rchelicopterfun Год назад

I list the basic items to check for cyclic pitch oscilation in the description.

@targetoz5470 Год назад

Hi John, rather than trying to bind a Spectrum radio to the H1 what radio is automatically compatible to the H1?

@Rchelicopterfun Год назад

As I state in the video and again in the description, compatibility has *nothing* to do with radio brand or protocol, it has to do with the receiver pairing; specifically that the receiver has an S-BUS output port. That is how this system communicates with the the RX via S-BUS. Nothing is going to be "automatically" compatible out of the box, it all requires radio setup and programming. I suppose if you wanted to distill things down to the most basic/seamless integration with the least amount of TX programming, you would get a radio that has Futaba channel mapping order out of the box (AETR), be at least 9 channels, and get a 9 ch+ RX for it that has an S-BUS output.

@stefano131978 4 года назад

could you please show the connections of the receiver (or the various types of receiver: futaba, PPM) to the H1?

@Rchelicopterfun 4 года назад

The H1 manual I link to in the description shows it well and goes over accepted RX connectivity. There is only one connectivity method as I show in the video. A 3 wire servo plug conductor to to the RX in port of the H1. The 3 conductors are the typical + / - / and signal conductors.

@MrDjrobyone 10 месяцев назад

hello and congratulations for your tutorial ... I wanted to know to install it on the trex 600 nitro, what problems can I find, in the installation, or is it like on an electric model? I don't understand where to connect the throttle servo to the H1..can you help me and give me advice on how and where to install it better? Thanks again

@Rchelicopterfun 10 месяцев назад

Doesn't work on nitro (at least I wouldn't trust it). 1. Only allows fixed throttle output so you can set carb position during priming starting, cold idle, fast idle etc. Also likely can't handle the high vibration environment of a nitro.

@bobsalvesen2070 2 года назад

John I'm having trouble calibrating GPS and H1...how do you keep from getting tangled up with H1 cable cause offline doesn't work well for me. Thanks for listening

@Rchelicopterfun 2 года назад

You mean the USB cable during compass calibration? If so, I never had any issue getting tangled up while calibrating the magnetic compasses; you just turn the the heli along each of the 3 axis the opposite way the same number of times on each axis so the cable never tangles.

@johnblythe6453 2 года назад

Got all working but F1 will not fire up ? green light on but not flashing ( most frustrating)

@RcBachelor 3 года назад

Another thing is, how do you stop the wobbling problem in your Vieo LOCK MOM ? Which settings do you change? I have same problems with the back/Tail going up and down.

@Rchelicopterfun 3 года назад

Like any cyclic wobble, it's tuning and experimentation. Play with the gain, the head speeds, and the head dampening. Even blade bolt torque can affect cyclic wobble. In short, all the usual stuff.

@gerryviloria4265 11 месяцев назад

hi john the h1 has a battery plug on its side what is the use of it. i know its connected in the ESC but i dont exactly know the function

@Rchelicopterfun 11 месяцев назад

Voltage monitor

@bobsalvesen2070 2 года назад

Hey John... me again sorry to be a pest but what should the radio switches be set on before calibration of GPS and H1... And what does the girl in video mention set for (stars)

@ConnorCain25 10 месяцев назад

Hey John, I know you have quite a few Ebooks to help with Heli setup. I was wondering do you have one that included 45+90 (H4) swash setup. I'm in the process of setup up a helicopter with this kind of swash and I'm really struggling with the geometry at the moment.

@Rchelicopterfun 10 месяцев назад

@ConnorCain25 - Sorry, I have no direct experience with 4 servo, H4 swashplates.

@ameersak 3 года назад

Hello John, can you also list the transmitters which will work directly with H1 without the need for extra receivers like AR7700 incase if we use spektrum. I dont mind buy a new transmitter..which one would u recommend for H1 directly plug and play?

@Rchelicopterfun 3 года назад

Transmitter model, brand, or protocol plays little roll in compatibility. As I state in the video and what is in the H1 owner's manual, it's the RX (receiver) that communicates with the H1 that is important. That RX needs either an S-Bus or PPM output to communicate the signals to the H1. The H1 has no internal RX, so you must use an external RX with the H1 - no exceptions! I'm not a Spektrum user anymore so I have no idea of which Speky receivers have S-Bus or PPM output ports but I do know they exist. One example is given in the description but there may be more (both Spektrum & aftermarket DSM2/X receivers). As for the DX8, it will work fine with the H1 (with the correct RX), but you will be limited with 8 channels if you want the invert function since it operates on channel 9.

@squashum778 3 года назад

Anyone might know what constant beeping GPS unit might mean? H1 gyro calibrated, solid green light before sticks down and out. Any ideas? Thanks

@LAIHEE41261 3 года назад

hi john! i followed all you did on your tutorial video and everything goes well. but when i connect it to the battery, i got stuck on blinking yellow light and the manual says helicopter preparing. it took forever for the yellow led light blinking. i did try to reset the FC again and no luck at all. still the same. do you have any idea how to fix this issue. by the way, i'm using a flysky transmitter and reciever 10ch and both support pwm ppm/ ibus sbus. any help please!!!!! thanks

@Rchelicopterfun 3 года назад

Sorry, no idea.

@danilogiovini5588 2 года назад

how should i set the trim and subtrim of the radio all to zero?

@Rchelicopterfun 2 года назад

As per your specific radio's instructions.

@bansheeparadox2678 Год назад

Hi do you have video how did you setup your radio transmitter for this one

@Rchelicopterfun Год назад

I cover my basic openTX heli foundation setup in this one: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XdFOndPG7xo.html It of course had to be modified slightly for the H1 due to the difference with pitch & throttle curves - ie. they are not used.

@bansheeparadox2678 Год назад

Do you pick airplane or helicopter model on your radio to set up h1 gyro, because i saw another video he choose airplane to set a heli

@nxtgen2b416 5 месяцев назад

Hi John. How do you like that transmitter and can I use spektrum dsmx receivers with it? Thank you 😊

@Rchelicopterfun 5 месяцев назад

I enjoy it very much. The way to fly Spektrum protocol is with an External Multi-Protocol module. If you update to Edge TX OS in the Radio, and run the multi-protocol module with the latest firmware via serial interface with the radio, you can even access all the latest Spektrum telemetry RX's along with forward programming access on their SMART stuff. Lots of info on the Multi-Module website and their GitHub threads. www.multi-module.org/

@timdoyle8199 2 года назад

Would it work with a futaba 7 channel radio, just wouldn't have inverted flight or ?? Thanks

@Rchelicopterfun 2 года назад

8ch minimum.

@johnclarke254 3 года назад

Hi John many thanks again for this great video. Just used it to set my Alzrc 505 with the H1. Everything seams OK, but not sure about the fail safe on channel 5. I have a Futaba 16sz, the instructions in the H1 manual have me confused. Any ideas. Also when entering the software and start with a new heli and work you way through until the end. You you enter the soft ware again you cannot go through these settings again you must start all over again. Many thanks John

@Rchelicopterfun 3 года назад

If you have channel 5 output setup correctly, you will see the channel 5 indicator in the setup wizard moving accordingly. So as long as you are seeing the 3 different selections (3D, GPS, RTL) come up when you move your 3 position channel 5 toggle, you know you have your channel 5 setup correctly. Since I don't fly with Futaba, I however have no idea how you set your failsafe channel positions so it defaults to the RTL channel 5 output if RF signal is lost. That would be in your Futaba manual how to set fixed channel outputs when the RX goes into failsafe. Yep, as I said in both the review and this setup video, one of the biggest limitations with the setup wizard program is there is no way to save the parameters, so if you go back into setup new heli, it wipes everything clear and you have to start all over again.

@johnclarke254 3 года назад

Thanks again for all of your help. John