Thanks for the video on the 1st Reg.. I was looking for those O-ring sizes!! This reg doesn't have an exploded view in Fx's pdf Keep these videos coming!!!
Hello Ernest, thanks for your videos, they are very good. I am new user in FX, but old in pcp guns. Recently I bought an M3 .25 700mm barrel. The first regulator is 150 bars, when I shoot, this regulator get down about 30 bars, then the pressure quickly return to 150 bars but after 2 hours from the last shoot the first regulator is 170 bars and keeps that pressure. Do you know what could be wrong?
Hello sir, I ve watched your videos time and time again. Much appreciated information, very detailed like no other. A question pls : Will this M3 bottle connector also fit Crown MK2 ? Looking for a way to make optimal use of my 300bar bottle i ve mounted on the Crown. Thank you. Lester
I have an issue with a slow air leak I have discovered that is coming the adjuster screw in the first reg I have replaced the o ring on the screw and the piston but it is still leaking air what could it be?
Buenas noches quería saber si podría ayudarme tengo fx m3 que tiene un inconveniente que el seilever no se queda trabado para que pueda poner el cargador o poder disparar el rifle si me podría ayudar se lo agradecería
Nice one! My first reg is showing bottle pressure so not working thought it might be the gauge so replaced it no difference I guess it must be one of those seals? Thanks Adrian
Ernst a person poster that when taking the 1st reg out they are so tight it damages the weapon before it breaks loose. Whats your experience with this.
Hi Ernest ive got problems with my dowti seal how can i fix it or if anyboby can help telling me ig you have problems with tat ahd how did you repair it ??? pleas help im in mexico exactly in torreon coahuila thanks and my best regards
Hi, 1st or 2nd reg?? If the reg can’t go above a certain high pressure one washer will boost the limit above 50b. Per example second reg 175 first rag 210b. Will make spring stronger so requires more reg pressure to shut the supply. Only required using high regulator pressure. For example us only 80% of the reg pressures capacity not 100%. Inside 2nd Reg body is 4x1.5mm oring
Hi Ernest i have that, exactly leak in my fx m3 i all ready , change all the o-rings in the regulator all of them and the leak still there, yeas it less, but it´s all ready leaking can you pleas help me what eles do i have to do ???? PLEAS HELP !!!!!!
@@ernestrowe5061 I stack my spring ()()()()()() and turn the adjuster 2X but still my pressure is 83bar.. Im afraid if i turn it more than 2X my 4X1.5 oring will burst again.. I have no stock on the washer to make it 13..
Try, checking the reg adjustments screw and the piston could be partially clogged. Use a small wire to clear the passageway. Or the bottle reg gauge tightened too much that is partially blocking the gauge or a faulty gauge,
ВОзможно у тебя давление первого редуктора слишком близкое к значению второго редуктор. Разница должна быть около 50 бар, иначе будет медленное заполнение.
hello! How can I get the first regulator to recover something faster? I have it at 150 bar and 2nd at 120 bar cal 25. Sometimes the first regulator recovers a little slow, which practically equals the 2nd and causes a low shot in fps, I have observed in your videos that it recovers quite quickly, what can I do, thanks!
@@ernestrowe5061 It never climbs above 30bar of creep, and it doesn't change when adjusting reg pressure. It was causing issues with consistency for sure. Having trouble with all 3 of my last fx purchases with consistency, but only the m3 with issues from creep.
@@deeparker6109 mine required the opposite to reduce creep. I've upped my 1st to 190 and the creep has reduced to 15bar. 2nd at 150 and consistency is now better and running lower hammer spring tension it's grouping pellets better and I can swap from .22 compact to 9mm, all that's required is an adjustment of the power wheel. From 6 to maxed. .22 @ 883 average to 9mm hybrids @ 967 average.
Hello, could I ask you for the exact dimensions and Shore rating of all five o-rings? I can't seem to find this information anywhere. I would be very grateful. Thanks in advance!!
@@ernestrowe5061 M3. If you look closely the internal structure of part 97 is not shown on the documentation. In your video you specify the sizing of some of the o-rings but nor all and not their shore #.
I'm sorry friend, but you didn't do anything if it doesn't show how your idea works, there is a person who has a channel I think called AirgunLR he explains and shows how it works after his idea
Everybody has there own point of view, i will explain in the upcoming tuning videos-> Cheers. And please don’t advertise other members channel here, please