gas piping ran to new gas range,stove/start up 

Great job Steve, I bet the homeowner's are happy they switched from electric to gas, much better !

Great job Steve. That was a nice stove. You did a Clean install on it.

That was a nice stove. Good job. Thanks for the video.

Excellent work Steve.

good video Steve. we basically use the same setup when cutting more than a few runs of gas line. we got an older rigid motorized pipe threader/cutter that weighs about 175 lb's. what a bastard to load and unload. cuts and threads like butter tho.

Nice install, Steve. Got that same stove this summer, except it's white. Good stove.

Quality installation Steven!!! The weather is getting better in our neighborhood! I could take "75 and dry" 365 days a year!!!

Very nice job, and a nice gas range as well (I have the same one)

Really good job! Hard to find people like you.

nice work Steve.

Good stuff, Steve ! Thumbs up.

Great video brother. Just what I needed to see! 👍✌

Nice stove, good job Steve.

Nice work Steve !!!!

I just put i lg mini split in April, I love it! Ducted for the upstairs bedrooms and non ducted for the lower 2 levels, so a 3 zone heat/ac system as well as my standard boiler heat. I wish I put it on the wall though instead of on the ground, didn't think of it at the time cuz it came with a base, now I gotta keep an eye on the snow around it.

That's a nice fancy stove. Never seen one like that.

another great job!!

I love that reamer! Adult size! You do beautiful work, experience shows.

Great Job!

Nice work. Clean install.

That is one clear camera picture of the bird at the end of the video ! Great quality camera.

you a bad man you know what your doing hands down

Now you just need to adjust the burners by taking each knob off and using a small Flathead screwdriver and setting each one to the right mix. It also would have been great if you could have shown us the install of the black iron pipes, heck a montage would have been great as well. I hope you have learned more and that your videos have gotten better, You really have a good thing going here.

Knowledgeable Video. Thanks a lot!!!!!!

Your pilot hole at :48 didn't leave enough wood for the threaded tip on the auger to bite so naturally it wasn't going to pull the bit through which is the main reason for liking auger bits. Back seat driving is easy but it didn't look like you caught what was happening. Everything else was very nice work!

great video!

Great job like all ways

Great Vid, Sounds like you're from Boston area, I thought I would see that sea-gull at the end turn to feathers .

Hey Steve, it probably wouldn't be a bad idea to check to see if the gas range is adjusted properly, sometimes the new ranges aren't adjusted quite right for the gas pressure in the building and it can cause excess CO.

Great job

Thanks for sharing.

nice stove

Good job

great video. if you can remember how far were you from the meter when you installed the 3/4" to 1/2" tee?

great Vid, quick question are you required in your state to make a drip pocket before each appliance? Annnnd, what type of Fritz do you use what gives it the blue look? Thx.....B

That was a nice looking stove.

I am new Subscriber. Can you do a coffee chat on how you got into the business? Did you go to school for Plumbing and HVAC ? You sure know a lot. I like your videos.

Recently added a 1/2” line for a stove for a friend. After I installed it, the pilot light kept going out on the water heater after a day or two of running. Thermocouple is fine, cleaned the burners etc. 1” main coming in, t’d off for the 1/2” stove line, and water heater line is 1/2”. Do I need to bump up the line that feeds the water heater to 3/4?

Interestingly, on Sunday I had to run gas pipe in the basement of the house that my boy just bought. He needed help carrying his washer and dryer down the steps. Then he asked me if I would hook up his dryer. One look at what was there and I said No Way. Nothing but one 15' long chunk of 3/8" copper tubing coming off a tee where the stove hooked up. The compression fitting where the tubing connected to the tee fell right out the moment I loosened the nut. It now has 1/2" black pipe running to the dryer with a good flex pipe for gas, as it should be. I don't know how that house didn't blow up on the previous owner, the compression fitting was sealing nothing.

I sure would have liked to watch you actually install those pipes and do that tee.

gr8 video.what about the strapping of gas line?

Great work, as usual, Steve. Heard Baby barking in the background.

Would you consider using a union In case there was a leak? You could work way back easier.

Very nice work! This job is a pleasure to look at, as hook ups for appliances in my part of Canada are either done in soft copper or this jacketed flexible stainless shit they have out now..

are u using a phone cam ?? amazing picture quality for a phone I think

Nice work....would be good to see how a leak shows up...another video?

I have a question about the diameter of the outlet on the meter. It is currently 1" diameter. I will have somewhere about 90' of pipe from the meter to the furthest appliance. So I would like to attach a 1.5" pipe to the meter. Can you install a 1.5" diameter outlet on the gas meter with 1" outlet? From my understanding, attaching 1.5" pipe to the 1" outlet on the meter would create a bottle neck right there? Thanks

How come you don't use copper for gas? In the UK it's used (although there are some old galv pipes still in use).

Ima li snimak kako seku pocinkovanu ili cev za gas testerom od 1 /2 " da je cev od 6 metara

Haha the whites socks

Steve, are you O.Q qualified to work on the D.O.T. side of the meter? Do you check the reg vent after turning the riser valve back on? Those old s254's are known to weep afterwards. You should probably say something about Johnny homeowner not touching those lockwings because they can blow the reg or sometimes snap that brass barrel. Might be 60lbs in that line.

hi good job i have question before energize main valve is there any test

Can you use the test dial on the meter to test for leaks?

hi. why do you don't use welding for gas piping ?

You sound like the Godfather... lol! Monday, Tuesday, Thursday, Wednesday... Nice work!

Ima li snimak kako seku pocinkovanu ili cev za gas testerom od 1 /2 " da je cev od 6 metara. Samo sečenje ručnom testerom

No bubbles no troubles Mamma

How much did you charge for that install? Looks like it took a bit threading your own pipe... gotta imagine its cheaper even with the time rather than buying pre-threaded? Nice video

Your augur bit is shot, haha

What about the excess gas that is still in the lines? Does it need bled?

Hi i need to do a gas line from the meter on my sidewalk to the inside of the basement. Please let me know how can i do it myself...or i need a professional

What kind of pipe dope is that

Hey there Steven, great video, thanks for sharing! I do have a question, if you don't mind...is a regulator required? Or are they usually built in to the stoves?

I hate setting stoves they can be such a pain in the ass . I see you didn't video sliding the stove in place lol. I don't care how many I do I always have a hard time getting everything lined up right. Good job though.

Steve , I know it's old video what is the name of special gas leak detector you use in this job ?

well done, how much does that pipe threader you got cost? is there any cheaper methods to make thread for that gauge pipe?

Sorry that was yesterday im uploaded one from the job site today. It should be done in a few minutes

How did you bleed the gas down?

7:48 Pressure tests always make me anxious.

Oak flooring is very hard, especially when it looks like the drill is in reverse, lol.

Might be time for a new pair of kicks my man!

what about the regulator for the new stove? don’t need one

3/4 drop on a water heater ? it's a pv50

Is your tool Ridgid ?

I have a dumb question. When you shut off the gas, isn't there still residual gas left in the lines in your house (to the water heater and furnace)? If you cut into the pipe to install a new line, aren't you draining the gas into your house?

What would it cost roughly to have a gas line shut off valve for a gas stove I presently have only a cap on it coming out of wall

whats your opinion on LG mini splits? do you recommend compared to other brands?

yeah that's the baby mama!!!!

Easiest way getting that T installed? Splitting that line?

The emergency control valve does not have a handle? What if there is a gas leak?

hi steve in america do not have to do a tightness test,gas rate, purge and relight and check working pressure when installing a new appliance. its a must the uk.

Not sure if you know but that reg on the gas meter doesn’t seem like the best place to be installed... should have some more clearance below the vent in my opinion. Not sure if it’s even in line with code in your area..

Very informative. After the gas is turned back on what is your procedure for the water heater and furnace as far as relighting or the pilot? Do you turn off the valve to each one prior to turning off the main valve to the house ?

It's up now

Overall, good job. First wipe off the excess pipe dope. It could conceal a leak. Leak test only a section at a time. By time you check out all the joints the bubbles could be done. Use a flashlight and don’t forget to check in the back of the fittings.

I did a test run today with a go pro I'm gonna try to put it up would you watch it

Mr. Steven, How long did that take you to install? I always wonder how long things like that takes.

we got a leaker mama

Nice job Steve I could of done it better but nice job

Anyone have a ball park estimate for a service like this ?

Nice job! How much was $ that?

Yo Steve. U should really buy some new shoes or nice boots. Them shredded old prison shoes and Kmart socks need a re-vamp pronto. Love your vids other than that

Shouldn't you have ran 1 inch up to the T where it goes down to the water heater? then you could have ran 3/4 to the stove.

Bad cough at 3:47, do you have pneumonia? Don't worry, a quick rest and you'll be fine in 2 hours. lol

What's the other way ??

Sorry to bother y'all but can we use the yellow tube/yellow RECTORSEAL Pipe Thread Sealant that has the red 5 on the label or do we need your white paste/brush stuff? Running black iron pipe/nat gas to new stove location in our kitchen remodel.

Hi.Were are you form?

Special leak detector

Most gas lines I've seen come through the wall.

Hey Steve nice job you could've used a manometer in and done a lot quicker though