Gasketing Application Tips: Permatex Tech Tip Series

Подписаться 16 тыс.

Просмотров 306 тыс.

50% 1

Curtis Haines, Permatex Associate Innovations Manager, walks through a typical gasket maker application using the Multi-purpose 5-minute gasket maker. He also covers the different types of product dispensers, how to remove old gaskets, and the proper cure times for the gasket maker you're working with.
Featured Products:
The Right Stuff Gasket Maker: www.permatex.com/product-cate...
Conventional RTV Gasket Makers: www.permatex.com/product-cate...
Ultra Series RTV Gasket Makers: www.permatex.com/product-cate...
SaferScraper Plastic Scraper: www.permatex.com/products/gas...
Gasket Remover: www.permatex.com/products/gas...
Please call 1-87PERMATEX (1-877-376-2839) or fax 1-800-432-2067 with any questions or comments.

Авто/Мото

Опубликовано:

30 ноя 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 132

@LunaDaSavage Год назад

"Don't apply too much material" Proceeds to apply too much material.

@hjer731 6 месяцев назад

worst bead I've ever seen

@Akya2120 6 месяцев назад

I was thinking the same thing... Glad I'm not alone. Not sure why they had Stevie Wonder apply the RTV there...

@socksonfeet8125 3 года назад

Me : Is that enough material? Permatex : MORE! MORE! MORE!

@chriswilliams2652 2 года назад

So basically, this was a demonstration of how NOT to apply the sealant, Cause damn that looked liked way too much. Also, I'd like to know if you completely assemble the part before it cures or partially assemble then fully torque after curing, I've heard different procedures.

@seanbouker Год назад

This is my question

@vermis8344 9 месяцев назад

"Hey, your video sucks! But I was wondering if you could help me with this..." 🤣🤣🤣

@hjer731 6 месяцев назад

dont let it skin over.

@hjer731 6 месяцев назад

@@seanbouker dont let it skin over. finger tighten and then torque down to proper torque figures after.

@jordanminnis6865 3 года назад

“Careful and consistent application” 😂 I thought this was a joke at first

@fighterNZ1 3 года назад

"Don't apply too much material" holy crap that's way too much. Half that will end up blocking up the oil pickup haha

@chriswilliams2652 2 года назад

That's what I was thinking...damn!

@chriscs9080 2 года назад

yeah kinda ridiculus for the company to have a video like this one

@LeoTheNinjaTurtleMan 3 года назад

For those saying they haven't seen someone lay that much gasket maker before, well now you have 😁

@drewandrews8673 4 года назад

He said 1/8” then applied 1/4-3/8” of material!!!

@cornell833 3 года назад

🤣

@supersabrosinho 3 года назад

Yumm! I love decorating cakes too! 🍰

@Lehmann108 4 года назад

Good Lord! That is way too much application of material.

@frenchtoast3562 4 года назад

decorating a cake this guy

@supra392 4 года назад

Agreed 1000% Jesus. But trust me.... they are sure that what’s in this video won’t cause a failure.... unless it’s the sealing surface for oil pickup between an oil pan and block lol

@MarkSegree 4 года назад

It happened to my first car. Wasnt fun, the mechanic was a family friend, I never spoke to him again after that day nearly 20 yrs ago and I use to see him all the time for the first 15. Common sense isn't too common, apparently it's like finding a crisp 100$ bill in the washing machine.

@supra392 4 года назад

Some of the shit I’ve seen at work on 6.0 and 7.3 Powerstrokes.... holy shit. I’ve seen multiple multiple tubes of silicone used to seal high pressure oil pump bed plates on 6.0’s. I’m talking the inside of the engine around the pump like alllll you can see is silicone leading down the back plate of the engine down to where the down tubes from the pump run down and forward to the branch tubes for the high pressure oil over fuel rails. And the engine DIDNT come in for a failure related to that silicone, it was in for a cracked piston etc from some junk tune they ran way too long. The point is, with this shit you can get lucky or VERY UNLUCKY, which is why I personally prefer gaskets whenever applicable.

@cornell833 3 года назад

Never a such thing as never yo much gasket maker no leak is what u want 🙈

@randabuffer6562 4 года назад

Can I have a little oil pan with my gasket of bead please?

@4dirt2racer0 5 лет назад

haha iv noticed this in just about every single video where a guys squeezin out permatex, but its too funny to hear the guy say to lay "make sure u lay n 8th inch bead" while theyre showin the guy use up a whole container on one part layin a foot wide bead lol :p i think thats probably just about the most iv seen somebody slather on somethin lol

@rachelsmith6820 3 года назад

🤣 and don't use to much or it will seep out the seems. I would say that definitely would seep

@MrD308 Год назад

Ok, serious question here. When using this product as shown in this video, are you supposed to put the RTV in the formed channel and around the holes or outside of the channel and around the holes? Is the channel meant as a holder for the RTV? I think I’m overthinking this. If you fill the channel and assemble it, will there be enough displacement of RTV to cover the whole pan flange? It doesn’t seem likely.

@alexurbaez951 3 года назад

Thank you very much.

@kx65fast 7 лет назад

the right stuff is awesome

@rachelsmith6820 3 года назад

Id rather wait the 24 hours unless dire emergency

@handyman7297 4 года назад

They need to edit this video on the "how to apply" RTV

@chicago1680 2 года назад

I love how he says don't over apply because it may squeeze out or go in and they put a fuck ton on lol. SMH

@mkj4390 3 года назад

great video, very clear and detailed explanation. Thanks!

@cornell833 3 года назад

Thank 🙏 God for awesome chemist

@mattjones1378 4 года назад

I bought a new oil pan and the area of the oil pan that mates with the engine block is painted a nice glossy black. Do I have to remove the black paint to metal for the Grey rtv to work?

@infotechsailor 4 года назад

I would! wire wheel on a drill bit, gget down to the metal and clean it with brake cleaner spray, then youre ready for 15lbs of Permatex like the guy in this video lmao

@trillrifaxegrindor4411 3 года назад

@qwertyui90qwertyui90 4 года назад

Which one is for upper oil pan to the bottom of a cast iron engine block ?

@cornell833 3 года назад

Black rtv

@MrAuto727 5 лет назад

Could you put fluid and drive your car in 12 hours? 15 Mile Drive. I don't want to put the stuff on it's going to leak or something I have to find a way to get to work

@trillrifaxegrindor4411 3 года назад

yes

@donnadieterich4307 3 года назад

I asked on information for John. Deer GT 235. Tram

@hcracer1985 6 лет назад

Ok. Once I apply the permeatex how long do I wait to mate the 2 surfaces together??

@justinkemeter 4 года назад

Msp-Protege exactly, it is a worthless how to video.

@mx1616 2 года назад

@@justinkemeter damn right! that's exactly what i was waiting for but hey here we are...

@user-xv7eb5ct9f 4 года назад

I used permatex black adhesive silicone sealant and waited 14hrs ...I then ran the car for 15min then drove around the block for about 5 minutes then the engine started smoking a lot .,.would this be because the sealant has not cured yet?

@Lehmann108 4 года назад

Yes. The smoke was from the leaking oil. You MUST wait 24 hours.

@mx1616 2 года назад

@@Lehmann108 hahaha don't mislead him. that's not true. he just probably sealed it poorly.

@oswaldoflores9206 Год назад

might be like 2 years late, but yes. 24 HRS cure time. I did the exact same thing and my tranny pan leaked. had to re-do the whole thing, and left the car dry for a whooole day.

@rachelsmith6820 3 года назад

When using a gasket remover doesn't have much in it and squeezes out too fast. Only need a little bit at a time. Also the brush that comes with is falls off easily so its better to buy a separate brush even if its a very cheap dollar brush to be thrown away.

@wildwoodtop Год назад

Best automotive gasket maker 🤔

@RocafellaAF1 6 лет назад

Good vid

@N3G4T3 3 года назад

You're going to have a lot of customer service calls on that number of they apply the amount that was applied in this video ahahaha

@cornfusedatbest6693 6 лет назад

Here's one for ya, how do you keep the Permatex from going bad after opening? This stuff isn't super expensive but it would be nice to use what's left in the tube.

@gimmetaco2037 4 года назад

Assuming you are talking about the tube... 1. Take a small piece of Saran Wrap, cover the open tip of the nozzle loosely 2. Tape the wrap around the nozzle. 3. Barely extrude some of the sealer out of the tip, filling the loose wrap (loose enough to get a 1/4" circle over the tip) and take the tube out of the gun. The stuff in the wrap may skin over but the remaining material (under the 1/4" trapped in the wrap) in the nozzle and tube will be "new".

@rachelsmith6820 3 года назад

After prying the dried up stuff out of top to use a second round i stuck a lead free pencil through the top. By lead free i mean the lead tip was removed prior to use.

@skullhart 2 года назад

Put in freezer in saran wrap

@davekana8388 6 лет назад

What should I use for my 2000 Dodge 2500 rear differential cover?

@trillrifaxegrindor4411 3 года назад

permetex black or permetex sealer for gear oil.

@kwesilynch1829 8 месяцев назад

I'm interested in becoming a distributor of your products in Guyana 🇬🇾 if you do not already have one

@shark3136 Год назад

Damn. Had to watch twice. Couldn’t break my focus on whatever that is on Curtis’s chin.

@user-qp3pc3xt1g 6 лет назад

Awesome

@tthams73 Год назад

The best use of any RTV is throwing it in the trash! Anaerobic is the best option.

@DSC800 2 года назад

Well, I guess if you are a company that makes sealant and you want more sales, you show people how to gobb it on.

@coreys121 4 года назад

Omg way to much and you dont have to go around the bolt holes just stay on the inside of the bolt holes. What a horrible video

@gimmetaco2037 4 года назад

Yeah, isn't that weird that Permatex would even suggest this?

@trillrifaxegrindor4411 3 года назад

@@gimmetaco2037 the amount on this oil pan would do 15 pans+.the reason they do this is to sell more product,there is absolutely no other reason. this one "piss poor" installation would absolutely blow the engine due to the oil pickup screen being completely plugged and obliterated with loose silicon

@Mark-wy1ux 3 года назад

@@gimmetaco2037 I guess they want to sell more product by having you use an entire tube in one application.

@changodrift 2 года назад

I like how he said 1/8 bead yet it looks like 3/8 lol

@daby8399 2 года назад

Well I just had this put on my car and it's still leaking

@chriscs9080 2 года назад

Did you follow the instructions? hand tighen let it cure for 1 hour and then tighter to specs . After 24hours should be ok to use

@garystone7062 2 года назад

Nothing adds enthusiasm like finding a little orange Permatex in a priceless 911S camshaft oil sprayer- Those no longer available S camshafts now need to be reground. Getting them out requires an engine drop. All because some idiot knew-it-all. Never allow gobs of goo to run around your crankcase.

@sfcd4757 Год назад

Am i the only one who struggles in squeezing the tube when laying a bead?

@terrythomas790 3 года назад

Geez, All that extra will fall off and seal his driveway also!

@danrodrigues3531 2 года назад

That permatex safer scraper isn't worth a damn. It took me two seconds to realize that it couldn't do what I needed it to do...

@Devo1987 3 года назад

to make things easier get a gasket when possible no need to add gasket sealer to most gaskets its not meant to be like that oh and no mess

@user-uc5vr8le7y Месяц назад

Hes gone and dorped it all on in there. The sump will be brimmed sith rtv.😂

@DanzZerous 2 года назад

Don't know why choosing a right gaket maker is complex and confusing

@permatexvideos 2 года назад

With all the new products coming out we understand it may be confusing. We have created new tool to help identify which product is best for you. Get the full experience: permatextraining.com/courses/selecting-and-applying-the-right-gasket-maker/

@dalesdaddy08 3 года назад

U want some oil pan with that

@difsid569 2 года назад

that's too much of the sealer

@johnkai2012 3 года назад

Is this a fake account trying to give Permatex a bad name?

@pingpong9656 2 месяца назад

Looks like permetex don't know how to apply a bead

@nationaliste007 3 года назад

Not enough

@ShaunRGardner 6 месяцев назад

I came here to learn the proper way to use you products and then you have somebody blast shit into the oil pan to probably cause blockage of the oil pickup. Great

@davidpuente2876 6 лет назад

Dude looks like Hank Basket lol

@johnstringer6401 4 месяца назад

IDK....he looks like he could be Pete Davidson's older brother! 😄

@2jzking124 6 лет назад

Silicone has to be inside the hole not outside 😂.now thit car is going to leak for the screws. Good job 😂

@Gaznick 5 лет назад

Seriously wtf hahahaha unbelievable

@chriscs9080 2 года назад

this wont gonna leak but parts of gasket may end up inside the engine !

@angelreyes629 2 года назад

HOLLY COW THAT WAS WAAYY TOO MUCH BUD 😱💀😅

@navaho5430 2 года назад

I know you want to sell the product but don't use a whole tube to do a sump, if i saw anyone using that amount i would kick there ass.

@boblazarrss 2 года назад

Dude looks like if stone cold and the rock had a baby

@chrism6 5 лет назад

what a joke of a video, way to much product is applied on the worked example. looks like the sales reps haven't got a clue, just reading from the paper with no real world experience.

@thatbig1 3 года назад

Lmao how much did he put on 😂😂😂

@cornell833 3 года назад

🤣

@chicago1680 2 года назад

all of it!!!

@user-oz3nt3kr2j Год назад

dont use to much then shows 3 times too much being used.

@arnoldwilson3719 Год назад

do not use a wire brush.

@psykro5735 3 года назад

0:38 more like the choice is up to your wallet

@Fueler 2 года назад

Lol unbelievable!!! This must be a not to do video?

@Arsing116 2 месяца назад

I think that’s too much 😢

@davidcisneros7621 2 года назад

What a mess 😦

@javieraranda2952 Год назад

That was nasty!!!!!

@accordingtohonda4308 5 лет назад

Well, if you follow this guide they're going to sell shit loads! BUY STOCK NOW!! I have never seen such an over application of a liqu... ummm well there was this one video... poor girl.