Hangkai 3.5 HP Outboard Motor Maintenance Internal Cleaning | FishingAdvNHF

Fishing Adventures of NorthernHardcoreFisherman | FishingAdvNHF

Подписаться 6 тыс.

Просмотров 26 тыс.

50% 1

In the previous video I dismantled the gear box (lower unit) of the Hangkai 2 Stroke 3 5 HP Outboard Motor and I did some cleaning including flushing the gear box, new gear oil was topped up.
**Share this video by copy the link below
• Hangkai 3.5 HP Outboar...
**Watch my trip at Air Papan Beach with Intex Seahawk II here
• Malaysia Fishing Trip:...
**Subscribe now by clicking the link below
ru-vid.com_c...
**Check out my other videos by clicking the link below
/ fishingadvnhf
00:11 Dismantling Works
02:06 Checking the Air Filter & Spark Plug
03:20 The Water Cooling System
03:45 The Cleaning
04:25 Checking the Carburetor
05:48 The Washing
06:37 The Assembling
08:21 Sneak Preview
In this final part I removed the housing of the Hangkai 2 Stroke 3 5 HP Outboard Motor and I dismantled certain parts, the housing was washed clean with dish detergent and rinse with clean tap water. The Air filter was removed and cleaned, due to the jerking occurred on my last trip I decided to check on the spark plug, a bit dense and carbon was built up on the spark plug, it was replaced with a new one which I bought in the later day.
Initial thought was to have the Carburetor stripped and serviced, when I opened up the Air Filter housing I found that it is very clean, probably due to low usage, I did some minor cleaning with a cotton bud. The Water Cooling System was checked and I used a vacuum cleaner to suck out any fine sand that mind trapped inside.
Lastly the whole engine was vacuum clean and a wet cloth was used to wipe clean the external.
Took my Intex Seahawk II Inflatable Boat and this Hangkai 2 Stroke 3 5 HP Outboard Motor that was just serviced to Kampung Mawar at Malaysia to try out the performance and fishing, the result? Stay tuned for the next video!
==================================================================================================
Please give me your valuable comments to help me making improvement and click the LIKE and SHARE if you find the video is good. Subscribe to my channel so you will not be missing out on the new videos, thanks.
You can reach me at
Blogspot
northernhardcorefisherman.blog...
Google+
www.google.com/+Northernhardc...
Instagram
/ northernhardcorefisherman
Facebook
/ fishingadventureofnhf
Twitter
/ fishingadvnhf
Tumblr
/ fishingadvnhf
===================================================================================================
Always Tight Line, Hardcore is the Spirit!

Опубликовано:

11 июн 2015

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 83

@jam010148 8 лет назад

I just purchased a 3.5 Hangkai with a manual completely in a foreign language. Your videos are quite detailed and easy to follow. I have already dealt with the gear cleaning and oil replacement -- see-spot-run -- after viewing your video! thanks

@FishingAdvNHF 7 лет назад

Thanks, glad that it helps you. Though I found that there's still more to be added into the video

@Mik-ly9sp 7 лет назад

Thank You very much for making this video its very easy to follow your instructions of how to take the engine apart for servicing then put back together afterwards. Your video is the first time I have ever seen inside a Hangkai motor

@FishingAdvNHF 7 лет назад

Thanks

@isaacsandoval3218 7 лет назад

Thank you for sharing that and the other maintenance video for the lower.

@FishingAdvNHF 7 лет назад

No mention

@BillyGirlardo 3 года назад

I figured I'd better order some replacement fuel lines and an impeller before I really need them so I emailed them a few days ago but I haven't heard back yet... Thx for posting.

@UPGardenr 8 лет назад

Thanks for posting

@FishingAdvNHF 8 лет назад

+UPGardenr My pleasure

@amrrashad5668 7 лет назад

Thanks for posting, that was really helpful

@FishingAdvNHF 7 лет назад

Amr Rashad No mention

@hayati4522 5 лет назад

thank you so much.

@therealjackfisher 8 лет назад

Thank you.. Love your video!

@FishingAdvNHF 8 лет назад

Thanks for the support

@therealjackfisher 8 лет назад

Fishing Adventures of NorthernHardcoreFisherman | FishingAdvNHF:)

@therealjackfisher 8 лет назад

+Fishing Adventures of NorthernHardcoreFisherman | FishingAdvNHF Liked and subscribed..

@FishingAdvNHF 8 лет назад

Thanks

@npham54 8 лет назад

Amazing in depth video!!! Thank you so much for this. I just got my motor in the mail today. What do you recommend to do before I even turn it on? You should definitely do a video for first time inspection of the motor, what to look for, and how to set it up for first time owners like myself. I'm part of a Facebook group that modifies and talks about the Intex Excursion 5 inflatable boat and some of us have this motor. We would love to get your input on first time setup and usage please if you don't mind. I told everyone there to subscribe and view your videos for support. Please keep up the amazing work!!!

@FishingAdvNHF 8 лет назад

Thanks for the support, glad to hear you like it. I would recommend you to have the lower unit gear oil replaced before you crank it up, the factory gear oil is not that good and it might have been store in the warehouse for god knows how long. When I did my first servicing after a few run, the color of the gear oil is in chocolate color. I will see if I can find some times to do an introduction video on this Hangkai Outboard, recently I was a bit busy with other commitments. NorthernHarecoreisherman

@thornyturtleranch6152 3 года назад

At 4 years how many hours do you think you have on your motor? How has it been running for you?

@williamg2776 9 лет назад

Please keep these videos coming, I am about to receive mine in the mail, and i find these very helpful how many hours do you think you have on that engine?

@FishingAdvNHF 9 лет назад

Bill Jerald I had been using this small outboard for about a year, I didn't really record the hours used, should be around 20 hours. So far it's working fine until recently it was jerking quite a bit and on my last trip the propeller just stop spinning, it was sent to a workshop but the mechanic couldn't figure out what is wrong. I am going over to the workshop later to find out more, hopefully nothing serious.

@LegereBen 9 лет назад

I was thinking about getting one of these but have been having second thoughts because of all the complaints about them. I was just wondering how it's been holding up, how fast it runs through a tank of gas and if it has enough power to go upstream on rivers or if it just chugs along at a walking pace.

@FishingAdvNHF 9 лет назад

Ben Legere No dout about it that this Hangkai had a lot's of complaints under it's belt, I did encounter some issues like jerking and the latest was the propeller not spinning. For that kind of price tag (I bought it at S$280) no other brand of outboard motor came close to it, so I guess I can still bear with those small issues. The Hangkai is quite strong if you ask me, but bear in mind that I am using a lightweight inflatable boat, the Intex Seahawk II. Not sure what kind of boat you are using, but for upstream on river I am afraid it might not perform as well as others. The fuel consumption is quite low, the inner fuel tank which's 1.5L can easily cover some 5km. I only use it on the sea and I wasn't quite sure how well it can perform in the river.

@JJG323 Год назад

How long did this little motor end up lasting for you?

@michaelfunke749 Год назад

What size spark plug? I’m trying to figure out but cannot.

@waleedamoun6796 4 года назад

how to adjust carburetor please

@TheHabibalby 9 лет назад

Excellent,,, keep up the good work... I'm going to start the maintenance on my engine I've seen some worried performance on my last trip.. Whenever I accelerate it doesn't move and some burning smell comes out... Any recommendations?

@TeckWeeAng 9 лет назад

TheHabibalby In fact I encountered the same problem, the propeller just wouldn't move no matter how I accelerate, no burning smell from my engine though. I sent to a workshop but I guessed my engine was too small for them to notice and it was not being touch for 3 weeks. I brought it back and was thinking of stripping off the engine to see if I can do something to it. Will see if I can make a video of dismantling it.

@TheHabibalby 9 лет назад

+Teck Wee “NorthernHardcoreFisherman” Ang same issue again I'm facing... :) if anything you made to repair please suggest... btw, do you have a Twitter account so I can start following you whenever you post a troubleshooting videos please...?

@TheHabibalby 9 лет назад

+Teck Wee “NorthernHardcoreFisherman” Ang I found your Twitter account.. @FishingAdvNHF and started following you...

@FishingAdvNHF 9 лет назад

+TheHabibalby Thank for the following, appreciate your support. Just wonder if you have subscribe to my RU-vid channel? You can do so if you haven't, it's "Fishing Adventures of NorthernHardcoreFisherman" @ goo.gl/5GQbP3 You might also wanted to follow some of my other social media platform, just go to "About" tab and you can find me on various of social media platform. Currently I am still working on the Malaysia Fishing Trip Series which is now at Part 9, a couple more episodes to go. I will begin the Hangkai Drive Shaft Repair and Cleaning as soon as I am available, stay tuned. Again, thanks for the support.

@fethibenhamed65 5 лет назад

I have hangkai 3.5 hp And i had preblm in the engine When I try to stared my engine i take a long time to start Can you tell the preblm please

@davidflow3483 6 лет назад

How do you change the lil water pump impeller that was sent? There's no video on that at all. Thanks David Lake Conroe TX.

@FishingAdvNHF 6 лет назад

You need to dismantle the whole lower unit and the drive shaft from the engine, there is a housing which has the impeller inside, just remove it and replace with the new one. I didn't have a video on that part, sorry!

@horacepotter2199 7 лет назад

My 3.5 was "jerking" "bogging down" "dying after 10 minutes or so of running. The problem...the air vent in the fuel tank was not designed properly. The vent hole had a rubber "flapper" that I guess was to vent and avoid fuel loss. It didn't work. I pulled it out and the motor has run flawlessly ever since then. Further, upon receipt, the carburetor was NOT adjusted at all. I couldn't get it to start or run until I adjusted the one screw carb adjustment. Runs just fine now.

@FishingAdvNHF 7 лет назад

Horace Potter Great tip! I definitely will have a look at those area, many thanks

@greato80 7 лет назад

Abouth third time i use my motor and i filled with fuel second time. After ten minutes of running, i hear pop noises and then i stop and motor shuts off. Then i cant start it again. Tried letting it cool but wont start.. whyd it make pop noise and how can i fix it?

@FishingAdvNHF 7 лет назад

greato80 I am not sure why there's a "Pop" sound, could it due to the fuel mixture? Maybe you can try making the mixture slightly lower, instead of 30/1 maybe 25/1?

@greato80 7 лет назад

Im not sure either but changed plug out with new one and starts up good now.

@FishingAdvNHF 7 лет назад

greato80 Happy for you

@waleedamoun6796 6 лет назад

carburetor Interface broken for 3.5 hp hangkai so i can not adjust the fuel with air How can i bay new one. can you sent link for it

@alekswhy88 4 года назад

How do I install a fuel tank to this motor? Why are there two fuel lines inside the tank?

@combat-aging 6 лет назад

Thanks good video. I have received my outboard but the translation from Chinese to English is so bad, it is not English. If you could do a video on the user manual, it would be great.

@JohnnyT0464 9 лет назад

How often would you recommend doing this service??

@FishingAdvNHF 9 лет назад

+FOAM KING - RC Creations For the Gear Oil I would recommend it to be replaced after 10 hours running, I mean if you are using the same type of small engine like mine, it didn't cost much on the gear oil. The internal cleaning is best to be done after every trip. My drive shaft jammed on my last trip and it was caused by some corrosion near the water impeller housing. Flushed the outboard with clean water after every saltwater trip to prevent damage. I have a upcoming video which I repaired the jammed drive shaft, I did the engine flushing as well.

@jimjohansen1879 6 лет назад

I took the carb off to get a better look at the throttle linkage and a very small black rod with a spring attached drop out of somewhere and I have no idea where it goes, does anyone else know, cant even find a pic of it anywhere

@FishingAdvNHF 6 лет назад

Wow! I didn't open up the carb as I afraid the thing you experienced might happen

@therealjackfisher 6 лет назад

Hey there friend, after years i bumped in to your channel to see how it goes.. You still got your Hangkai?? Mine runs like a dream, i just fired it up.. It started after 4th pull.. Amazing after storage for so long.. I think it was like 3 years i had it stored now.. I am thinking about installing an air filter to reduce some of that noise and i think it would be a good thing for the engines health too.. What's your thought on that?? Engine is lovely it runs on sea, on lakes, on rivers.. It is just so loud i had to get a trolling motor.. After i got that 56lbs trolling motor i must say im happy i have Hangkai.. It weighs like what 5 kg?? And it is a powerful engine 3.5hp 10 times stronger then 56 lbs.. My 56 lbs engine is big, long shaft, and much heavier to carry then hangkai.. It is smaller tho.. But put a 100AH battery on top of that and you have a monster to carry around .. I thaught these trolling motors were light like plastic.. I was wrong.. If it wasent for the noise i would send back my trolling motor and keep using only Hangkai.. That noise level must be modded somehow.. it is waaayyy too loud.. Got any ideas?

@FishingAdvNHF 6 лет назад

Thanks for tuning in, it's been quite a while since I last updated this channel, been busy with works. Anywway, my Hangkai is dead! The last time I checked on it, found that very high chance the Auto Clutch has worn out. I haven't got the part ordered and since then the Hangkai was kept on the shelf. As for the noise, I can't agree more with you that it is loud. Not sure how to add on the air filter to reduce the noise but I would love to get an update from you if you decided to get your hands dirty.

@therealjackfisher 6 лет назад

Yeah bigger air filter and maybe modded exhaust system.

@noambiton1392 9 лет назад

please i need you to do a video about changing fuel in the engine its important for me to know all about this engine! thanks very much

@FishingAdvNHF 9 лет назад

NoaM GamimGs What do you mean by changing the fuel?

@noambiton1392 9 лет назад

Fishing Adventures of NorthernHardcoreFisherman when the fuel over what i need to do te refill the fuel do a video about thats thanks !

@FishingAdvNHF 9 лет назад

Oh I see, I did make a Fuel Refilling gadget for it. Using the squeeze bulb fuel pump with two fuel pipes connected. ok, I see what I can do for that one.

@batsonlogging 8 лет назад

Where do I get one? I really like your video.

@FishingAdvNHF 8 лет назад

Thanks for watching and supporting my channel. Firstly I would like to apologize for the delay on uploading new video, it's has been a busy month and I was held up with some personal issues, (P.S. I couldn't afford doing this full time, at least not yet.) hope you can understand, thanks. The Hangkai was bought some to years ago and I got it from the Chinese Online Store Aliexpress. The last time I check they are still selling this model as well as the newer model which is around USD$350. There's 4 stroke engine versus mine of 2 stroke engine, price will be higher but I would suggest you go for the 4 stroke engine as it's more efficient and less hassle as you do not require to make the gasoline mixture. Here's the link if you wanna check out the pricing, delivery might take long though. www.aliexpress.com Cheers NorthernHardcoreFisherman

@texjames2000 7 лет назад

Anyone found where to buy spare parts? Say like the air filter, lower unit seal etc? How about a video replacing the water impeller?

@FishingAdvNHF 7 лет назад

Search for Aliexpress, you can get most parts there

@jaredgarcia4697 7 лет назад

I have the same motor and when I have it at full throttle once it get warmed up it does that jerking motion and bog downs almost like it wants to die and then goes right back to full throttle. Do you have any idea what causes this problem?

@FishingAdvNHF 7 лет назад

I faced the same problem and eventually it stop working, I found out that the shaft was corroded and jammed. The Auto Clutch must have worn out, you can get the part from aliexpress.com

@greato80 7 лет назад

I have same problem with my new hangkai..but read on a comment that it needs to be broken in slowly on lower speed for few hours. Cant just start up and go low to high. So maybe run yours in a barrell or plastic tub of water awhile on low to mid gear to break in. Again, its just from a comment i read about the same kind of problem..makes sense to me tho. Im gonna try it.

@martinthibeaux317 2 года назад

JARED-----Notice the air bubbles in your fuel line----it is not SNUG onto the motor and causes it to run badly. You have to thicken up the metal tubes on top of the carburetor by using JB Weld smeared onto a small piece of paper towel. A couple of wraps will make those tubes fit tight. You need to put it up on a bench and take a "surgical" approach to this......takes a couple of minutes, really, and let the JB Weld cure for a day. All of my Hangkais have this problem, but run well, otherwise......Marty the Designer

@zachhoyt92 8 лет назад

two questions, whats the gap call for on spark plug? I seen a few post using 93 octane with a 25:1 mix for best result? I wish I had a manual for this lol

@zachhoyt92 8 лет назад

sorry 30:1 mix ratio

@FishingAdvNHF 8 лет назад

+Zach Hoyt Sorry for late reply. I always used 95 octane with the 30:1 ratio on the 2T mixture. The gap call I wasn't sure, I didn't went to that detail and I just tighten it. I know it's not appropriate but the manual don't have the figure and I just did it like what I done to my car's spark plugs. : )

@zachhoyt92 8 лет назад

Hey fishing I figured out the best thing for this motor I just cant figure out how to show the picture

@FishingAdvNHF 8 лет назад

Maybe you can try emailing me? angteckwee@gmail.com

@npham54 8 лет назад

Would you mind sharing his tip and picture please?