HD Toothpick FPV drone build || Flight test 

Great minds think alike 😁🤘.

@@andrewmedia3568 hell yea bro! I'm so hooked on this shit. I can't get enough. Big fan of your videos. Cant wait to see what you get into next!

@@DaywalkerFPV I really appreciate it. I’ve got some more videos in the works. More builds and testing for sure.

Thanks 🤘.I totally agree awesome performance from a small size. Now in hd thanks to walksnail.

@@andrewmedia3568Sorry about the damage, just saw the end. I kinda screwed my HDzero whoop board or mipi at a bando recently so I feel your pain.

@@derelictfpv yeah very sad lol. I’ve got another board on the way. Hopefully will last longer than 2 weeks this time.

No problem glad you enjoy them. 🤘

Thanks 😁

Thank you 😁 forget to add the total.

That little drone is almost the same price as my 5" lol😂

That’s a good idea thanks. 🤘

💪 Hey Thank you I appreciate it !!

Man it’s worth it. Full hd in a 2s toothpick is something else. The v1 fatshark dominator hd goggles are on sale for 380$. I paid 480$ for mine just before caddx released the goggles x.

dang, ok thanks for the info.

@@andrewmedia3568 bardwell actually has a video for it too that’s how I found out. I’m doing a build with the same aio board as you ! And the 1s lite vtx kit. And was worried since I was planning on using it with a 3s I saw it’s rated for 2-4s

@@josephmendoza2935 the v3 1s lite is 3.1-13 volts so as long as your in that range for input voltage you should be good to go.

Yes the V3 board does support 3.1- 13V . From my testing and what ive seen for best results go for either a 5v or vbat if you are running 2-3s voltage. Im running mine to a 5v plug and 2s voltage and its been great. Its better to have it running to a voltage higher than 3.1 but obviously not higher than the 13 volt threshold.

@@andrewmedia3568 Yeah I'll be running 2s and/or 3s batteries on it but just wasnt sure if i need to change it or not. the default on the AIO is 9V so i shouldn't HAVE to change it correct?

correct 9v would be perfect. 👍@@imagin311

It was super hard 😂. I used tweezers and a small allen wrench. You have to kinda squeeze and push some through and then carefully pull it through without tearing it too much.

Use fishing wire or dental floss. Wrap it around the rubber grommet and pull the string in first. And feed the grommet thru the hole while pulling on the string. Try it. Easiest way 🫡

The AIO is fine. Never had an issue with the FC.

If not too heavy, floss in-between the motor stem and the prop works well too.

Not sure where I can post a BF CLI dump.

​@@andrewmedia3568 Post link to the file on google drive, or just put PID and filter section of dump in this conversation.

@@maciejdYm # profile 1 set profile_name = - set dterm_lpf1_dyn_min_hz = 75 set dterm_lpf1_dyn_max_hz = 150 set dterm_lpf1_dyn_expo = 5 set dterm_lpf1_type = PT1 set dterm_lpf1_static_hz = 75 set dterm_lpf2_type = PT1 set dterm_lpf2_static_hz = 150 set dterm_notch_hz = 0 set dterm_notch_cutoff = 0 set vbat_sag_compensation = 0 set pid_at_min_throttle = ON set anti_gravity_gain = 80 set anti_gravity_cutoff_hz = 5 set anti_gravity_p_gain = 100 set acc_limit_yaw = 0 set acc_limit = 0 set crash_dthreshold = 50 set crash_gthreshold = 400 set crash_setpoint_threshold = 350 set crash_time = 500 set crash_delay = 0 set crash_recovery_angle = 10 set crash_recovery_rate = 100 set crash_limit_yaw = 200 set crash_recovery = OFF set iterm_rotation = OFF set iterm_relax = RP set iterm_relax_type = SETPOINT set iterm_relax_cutoff = 15 set iterm_windup = 85 set iterm_limit = 400 set pidsum_limit = 500 set pidsum_limit_yaw = 400 set yaw_lowpass_hz = 100 set throttle_boost = 5 set throttle_boost_cutoff = 15 set p_pitch = 54 set i_pitch = 101 set d_pitch = 33 set f_pitch = 131 set p_roll = 51 set i_roll = 97 set d_roll = 29 set f_roll = 125 set p_yaw = 51 set i_yaw = 97 set d_yaw = 0 set f_yaw = 125 set angle_level_strength = 50 set horizon_level_strength = 50 set horizon_transition = 75 set level_limit = 55 set horizon_tilt_effect = 75 set horizon_tilt_expert_mode = OFF set abs_control_gain = 0 set abs_control_limit = 90 set abs_control_error_limit = 20 set abs_control_cutoff = 11 set use_integrated_yaw = OFF set integrated_yaw_relax = 200 set d_min_roll = 29 set d_min_pitch = 33 set d_min_yaw = 0 set d_max_gain = 37 set d_max_advance = 20 set motor_output_limit = 100 set auto_profile_cell_count = 0 set launch_control_mode = NORMAL set launch_trigger_allow_reset = ON set launch_trigger_throttle_percent = 20 set launch_angle_limit = 0 set launch_control_gain = 40 set thrust_linear = 0 set transient_throttle_limit = 0 set feedforward_transition = 0 set feedforward_averaging = OFF set feedforward_smooth_factor = 25 set feedforward_jitter_factor = 7 set feedforward_boost = 15 set feedforward_max_rate_limit = 90 set dyn_idle_min_rpm = 0 set dyn_idle_p_gain = 50 set dyn_idle_i_gain = 50 set dyn_idle_d_gain = 50 set dyn_idle_max_increase = 150 set level_race_mode = OFF set simplified_pids_mode = RPY set simplified_master_multiplier = 105 set simplified_i_gain = 105 set simplified_d_gain = 95 set simplified_pi_gain = 110 set simplified_dmax_gain = 0 set simplified_feedforward_gain = 100 set simplified_pitch_d_gain = 100 set simplified_pitch_pi_gain = 100 set simplified_dterm_filter = ON set simplified_dterm_filter_multiplier = 100 set tpa_mode = D set tpa_rate = 65 set tpa_breakpoint = 1350

Damping : 0.95 Tracking: 1.1 Stick Response: 1 Dynamic Damping: 0 Drift Wobble: 1.05 Pitch Damping: 1 Pitch Tracking: 1 Master Multiplier: 1.05

@@andrewmedia3568 grande 💪💪

Thanks! Installed a new vtx and it’s all good now.

Mistakes were made 🤣