Hisense tv won’t turn on red light blinking: How to change a capacitor and fix TV 

This is nothing more than a recall when it becomes a pattern. Thank you Amy.

Capacitors went bad after a storm. This video showed me all I needed to know. Took about 2 hours as I had never soldered before. Thank you!

Just a couple pointers 1. Get a desoldering gun it will melt the old solder and suck it up so you don't have to fight with getting the leads into the holes 2. Do not pre-tin the leads on the capacitor it makes the leads thicker and harder to get through the holes. 3. Do not trim the leads before you solder the capacitors back into the board keep them long this helps with alignment just insert the leads and push the capacitor down to the board as far as it will go don't force it then on the back side of the board put a slight bend on both leads at the board this will hold capacitor in place long enough for you to solder 4. Also when discharging the capacitors it's recommended to use a 20k ohm resistor across the capacitor terminals this is much safer than a screw driver

Good job ❤️👍for someone who doesn't have much knowledge about electronics. Careful🙏 before discharging capacitors. The one you discharge and make a big spark was the high voltage capacitor ⚡🖐️. It's was around 350 volts. ⚡. To discharge a high voltage capacitor you need a resistors. Around 220 omh. It's not safety to discharge it with a screw driver. The soldering must heat enough so you can disoldering the joint on pcb easily. You must heat the old soldering on the board with new soldering leads. Then it will be easy for you. If not you can use desoldering pump vacuum also. Next when replacing the new capcitor no need to cut the pins. Just insert it and afrer soldering on the board you can cut it. Never add soldering leads on the capacitor pins before inserting it on the board. The hole on the pcb is so small. Overall it seems OK if you had inserted the capacitor correctly in the direction needed. But I seen the soldering is a bit loose. You need to apply it near the board. I have a hisense tv also. 🙏😊 Nice to see your TV working.

I just wanted to say thank you. I had an issue with my 70in ONN TV, and this actually was the problem. I will be tagging you in my video.

Your first time and you all those soldering techniques 😮

Great video. Same problem. You are very wise. Thanks for posting.

if you power your TV directly in the wall plug and don't use a proper "surge protector" power strip (it must say "surge protect" or "surge suppress" on the power strip), then a storm or sudden surge on the power grid can blow the capacitors. ALWAYS run your more expensive components, such as TVs, audio, PCs, Laptops, Roku, etc. on true "surge protectors." APC and other companies have really good surge protectors. Some folks plug into a power strip that are simply a "relocatable power tap" that don't have surge suppression.

👋👋 well done..a good effort ...just a few things which have been mentioned, personally I also like too make the sponge a bit damp.

Thanks this helped me fixed my 55 inch Hisense Roku tv.

Great tutorial amazing

for a woman, you did it! that's having courage keep going! greetings from Bolivia😘

thank you

This is insanely impressive. I've never been brave enough to fix an LCD Panel. (I think an O6's tv broke and nobody wanted to take it apart because of the capacitors!) I think the only thing I successfully soldered was a CAC reader that had cables that kept coming loose. I would caution that most "Tin" has lead it it so you would probably want to wear some type of gloves and work in a Very Very well ventilated area and wear a mask too.

No need to tin the cap legs, it makes it harder to fit the cap legs in the holes, also before you remove the old caps add new solder to the pins 1st, this will help the original solder to melt quicker.

Wow smart lady

do u have to take every connection off for new capacitors to work

Thank you for this information. I replaced two of mine and it works perfectly. I put two 400 in mine replacing the 350.

Sir , my self mayur redkar Three time light blink hote hai to kya issue rhe gaa

what if u have changed capacitors & tv still does same thing?

LOVE UR VID LOVE UR STYLE . 10POINTS ****** STARS 👏 & SOME.

เก่งสุดยอดครับ

Good job for a girl I have the same tv same problem same blown capacitors wish me luck

great video, i had same issue with my tv but didn't fix mine.

I have what appears to be a similar tv. No blown capacitors, no screen, and blinking red light (faster blink than yours). Still diagnosing.

can you tell me capacitor model thanks

What if the capacitors are not puffy up top?

I have a vizio tv I had about four years. when I Purchased it I was Browsing through ebay and they had 65 inch like mine that had a cracked screen they were selling all the circuit boards out of. So I have all brand-new circuit boards in a box in my office closet. I hate to throw anything away so I'm going to replace the Capacitor's and put the new one in and save the old one as a spare.

Hi @echoingamy could you please share me the link to capacitors that i need to order and also the soldering machine

Te falto la pasta de soldar y un extractor de estaño manual

Use the heat on the solder to get the grease off that oven.

As an engineer this was funny to watch it reminded me of the labs we would do in college😂😂

I now have two tvs with blinking red issues, I wish I knew how to test if it’s the capacitor or circuit board or power , do they sell a testing kit for tvs to learn?

Do you know the model number of the TV Good video Thanks

COOL👍

Where did you buy your tool & capacitors from?

Thank you I fixed my TV watching you. Queen Shit👑❣️

Have the same problem with my tv but none of the capacitor are blown like urs?

Wow well done girl, very nice, and your voice are beautyfull, a hug from mexico 🤍💚❤️

i have a red blinking light but not displaying anything on screen any suggestions?

could these capacitors go bad without "swelling"?

omg thing almost shocked her. ima try ta do this for my fcked up tv

Is the sponge wet?

Bravo 🫡

Mine doesnt even show the hisense logo

É condensador chinês não dura nada

Replacing the board is only 39 dollars.

blew out her compasiter XD

** You're not only Pretty your Smart too **