Homemade 300cc TANK / PART 6 ( Brake, Seat ) 

17:21 Wait so to understand, the purpose of the breaks acts like a steering, like if you wanted to go left you'd have to break the left break in order the right tracks push the tank to the left... Smart.

I've would have reversed the master brake cylinders so you pull not push the levers, so it would be more natural in way of you are braking that side(or slowing down that side) to turn! With the fact that I'm going to guess you'll be adding a throttle petal to rev up the engine which will in gauge the engine to the transmission as well!

Ready for part 7! This tank is bad ass! Good job! And greetings from America! Good luck and keep building!

Thanks for adding captioning!

Love this build Friggin Awesome👍

I like that it’s direct drive but for Safty you should put a clutch on that engine so at idle it’s not trying to take off on ya

I really like the brake setup. Looking good. Cannot wait to see it finished. :-)

Thanks for sharing such wonderful content with your audience. It is very interesting stuff. I appreciate all the work put into it. Sincere thanks!

Napravi na tenku grn za snijeg da mozes cistit snijeg kad zapada.😁😂

Omiljeni si mi jutjuber samo tako nastavi !, nonstop mislim na tutorijale, auta, tenka, i ostalih stvari , najbolji si !

It will move forward, but turning requires too much power. When one side stops, the other side will start spinning much faster and loosing torque. Also uneven terrain will cause issues of the tank automatically turning instead of going over the bumps

Dobar video, jedan si mi od omiljenih jutjubera, voleo bih kad bi nekad napravio auto, npr da uzmes samo školjku od auta, a ti da stavljas delove, posebno bih to voleo da bude Yugo ili fića. Pozzz iz Srbije🇷🇸.

Great job I am very impressed I wish I could help you finish awesome job

Doctor D.S., Nice build so far. I am surprised you didn't build a brake system, using pedals... like a Farm Tractor, to free your hands to operate other equipment. That tank is going to be heavy when it's done; you may have to use a set of step-down gears to muliply the Torque from the 300cc engine enough to move it, without stalling once you engage the cluctch. (translated by google) Lijepa gradnja do sada. Iznenađen sam što niste izgradili kočioni sustav, koristeći papučice ... poput poljoprivrednog traktora, da biste oslobodili ruke za upravljanje drugom opremom. Taj će tenk biti težak kada završi; Možda ćete morati upotrijebiti skup zupčanika kako biste ojačavali zakretni moment iz 300ccm motora kako biste ga mogli pomicati, bez zastoja kad uključite kvaku (preveo Google)

I am going to give this a shot...had a dictionary on my shelf surprisingly. volite svoje videozapise. nastavite s dobrim radom i sretno! Hope I got that right!

The tank is looking great my friend !! Will it have a working turret? We will see . Man it's been just awesome watching you build it ! Your next project after this one will be a joy to watch to .

Cant wait to see next part

It's actually awesome for real...

Está ficando muito top demais.

It's coming together man, nice work. I don't have any criticism, because I don't build tanks, so I wouldn't know what I was talking about anyhow. Keep up the good work, can't wait to see this beast roll.

Es geht voran. Sehr interessant.

Parabéns um mestre!!!

You mention your “TURNER” regularly. I figure you are talking about a “Machinist”. You should give him a shout out by name. It seems he does good work for you. Just a thought. I am enjoying you build videos. I’m just wondering if you will mount a light machine gun, heavy machine gun or cannon on it when you finished. 🤣👍🏻🇺🇸

hello , i have a question : can you make the "armor " of the tank ?

It`s some realy nice work of machinery skills, the thought and the carry out with the building using your one ideas, As I said Before Hat off, Stefan from Sweden.

You should add a clutch to disconnect the transmission so you can stop and go without being thrown off. Not to mention the tank will stop instead of the motor continuously trying to go forwards and might not actually stop. Not to mention you should have ripped out the full Automatic Braking System of 2 cars and put it in instead. It will make turning smoother instead of a constant jerking turn it will have. And lastly if you ignore everything else, just don't forget to secure the brake lines.

Seguindo cada vídeo ansioso. Parabéns. Muito bom...

Moc zajímavé.Jsem zvědavý, až nasadíš pásy a uděláš první projížďku.:)

Odličan video 👍👍

Félicitation de cette fabrication et bon courage à l'avenir

A suggestion, you should put some strips of metal to the tank treads so it has some digging in power instead of just riding on slicks.

Está ficando muito top esse seu projeto.

All I want to see ,is two pistel grip shifter handles on those two levers. Great job in a nice small shop 👍

Ótimo projeto, parabéns aqui do Amazonas - Brasil...

Wow, very great bro!

finally, new part. yeaahhh

Your work is pretty good buddy! Like!!

Very smart designs.Bravo !

I dont Speak Russian ....But I Love these Videos Comrade!!!

You rock brother!

Очень не дурно для первого раза , очень много выйдет в процессе эксплуатации недоработок , а пока мой совет это реверс- редуктор ! С уважением из России ! И удачи в проэкте ! P.S. в следующий раз начни с тех задания перед постройкой аппарата .

Samo čekam da prodje jedva čekam da počne burazzzzz

أحسنت ، واصل العمل 👏👏👏👍👍👍😉

Nice brather 👏👏👏👏👏 I like it .. 👍👍👍👍👍👍

Bardzo dobra robota. No tak.

Hallo Doctor D.S. I from Indonesia, I'am waiting part 7 from your videos, I like your videos👍

Thumbs-up from California

It's very good to see your steering solution to shut up the cynics about the differential use. Well done.

Well Done Now i know how your Clutch will work hopefully😏😏 One of your Barke Zylinders is very lose to the crankshaft Hopefully the crankshaft dont collide with the Zylinder Your Projekt is very interesting I look forward to the next Episode Yours Frank

Nice video bro.....I m aamir khan frm Pakistan islamabad ur video nd channel is god

Idemo plako do 1 milion samo naprjed

Te felicito!!

You are very smart boy !

nice idea the braking system with a normal differential nice work man :) good work young man cheers from Montreal ,Canada :)

I'm still watching this video

Highfive ! Lepo i dobrowolski 👍 Bravo Bravo Bravo kao Leopard 2 🤣 Regards ti Molis

BRAVO MAJSTORE !

You may need to have the drive “wheels” at the rear. That way under pressure the tracks won’t ripple under the machine. Like a dozer has

Yeah it’s all well and cool to steer but you still need a clutch, MUCH lower gearing, and a transmission. Otherwise it’ll be too fast with not enough power, will go forward as soon as you turn the engine off, and won’t have any capability of stopping or reversing.

Good job doctor d.s👍

Awesome work👍👍👍

Svaka ti čast majstore

very good❤️

Great video from Australia 🇦🇺

Sretno dalje legenda si

You really need to remake the control handles. I would cut them weld them to go over the top of the control canisters and then angle up. That would take the handles from touching the seat and still allow free movement. Just my opinion...

Mislim da bi bilo bolje da si gas metnul na nogu. Ako je frka samo makneš nogu s gasa, a ovak, dok ga nađeš, povučeš ili gurneš, možda bu kasno. Gas i kuplung na noge, tak da su ti ruke slobodne za upravljanje i kočenje. Trebaju ti obje, nije to volan. I samo polako, imaš vremena.

awesome work =)

Exceptional work. Maybe I would have moved the control levers to the sides of the seat. Until next time

svaka cast bit ce dobar tenk

Dude preparing for ww3

I think that's the first time I've ever seen a brake system bled even before it was fitted !! I also wondered, did you weld the cast Iron caliper supports to that piece of box ? If so the cast will probably crack.

Few tips from dear experience , The brass throttle cable stop on the end will be a hinderance of wearing out on the small metal bolt from wiggling back and forth they ware out fast it will leave you sitting somewhere been there done that , , I`m really curious what your going to use to keep the tracks tight -A slip wheel like on the Caterpiller front idler will work great on this or TORSION bar Wheels somewhere on the track system ,, And don`t forget to stand this up on end or tip it over to weld all the joints underneath or they will fill with mud and water and rust or split constantly ,, The bolt holding the levers will be a bear when removing with rust ,, BUT GREAT JOB SO FAR !!

Frankenstajn💪pola od BMW-a pola od golfa😂

What happened to this tank my friend?If you have stopped the construction,could you,if you please, tell us what is happening?I really enjoyed watching the videos on the building of your tank! Alright?

very cool your videos I am registered I live in Brazil

Awesome!

You are great master bro you are very sucsess person

this is cool the only thing im worried about is the rust on the frame

Extra maszyna 👍

Mali svaka čast na trudu, snimanju, dobro izkadrirano, režirano 👍

Молодец! Привет из Беларуси!

Может чего-то не понял...муфта где, кпп, задняя??? А так прикольно!

This thing is awesome, but I would have put the seat higher than the motor and lengthened the brake levers. And I hope you do some sheet metal work and do some aesthetic finish work

Seat is too big... I think you have to use a go-kart one

наш парень . руки из нужного места растут :))

perfect !

dobri den, i was wondering which soldering machine you are using? It looks like it's a good one, i'm about to purchase one here, so i'd like advaces. For the tonk, keep up the good work, you're doing great !

isnt it gonna rust up pretty bad he is putting alot of good hard work into it

"Vladimir putin wants your location"

Showwwww my friend brazillll 🇧🇷

Chido tu proyecto👍

Muito legal show 👍

legenda si

เยี่ยมมาก

Odlicno, samo mislim da si trebao ove rucke od kocnica stavit sa lijeve i desne strane sjedala, tako da kada se fino sjede budu pri ruci za uspravljanje, pozz!!

I WANT VIDEOS FASTER AAAAAAAAA! sorry jk good work

Reverse the controls. Pull not push to turn.

Svaka cast care

As a tank mechanic i find some youer mistakes but any how you done well