Тёмный

Honda CBR 1000rr - How To Change Brake Fluid (ABS) 

Motorcycle Maintenance Channel
Подписаться 2,9 тыс.
Просмотров 12 тыс.
50% 1

Опубликовано:

 

11 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 19   
@thagingerninjer5391
@thagingerninjer5391 Год назад
It’s a lot quicker if you take the cap off of the reservoir, then suck all the fluid out, and replace it with new fluid before you start pumping and draining.
@motorcyclemaintenancechann2131
We do that in future videos, definitely saves a lot of time (and editing!) Thanks for advice, we love the motorcycle community and are always looking to improve the videos, plus share what we learned. Keep watching & Ride Safe!
@thagingerninjer5391
@thagingerninjer5391 Год назад
@@motorcyclemaintenancechann2131 you, too, man!
@Team-fabulous
@Team-fabulous 3 года назад
Why did you not bleed the pumps!?!?! You have only done half the job..
@thagingerninjer5391
@thagingerninjer5391 Год назад
Because you don’t have to.
@Team-fabulous
@Team-fabulous Год назад
@@thagingerninjer5391 of course you need to bleed the pumps otherwise the fluid goes stale and will damage seals
@rommelaufdaucuh4855
@rommelaufdaucuh4855 3 года назад
Thank you very informative
@motorcyclemaintenancechann2131
@motorcyclemaintenancechann2131 3 года назад
Glad it was helpful!
@gc33
@gc33 9 месяцев назад
Don't need to open bleed nipples so far.. Only crack them so you can feel the lever bottom out. And as said previously your over tightening the nipples. Only need to be nipped up...
@johnnyblaze1372
@johnnyblaze1372 3 года назад
is this a sc 59?
@dr.speedlemon739
@dr.speedlemon739 3 года назад
No, its an sc77
@coolwicia
@coolwicia 3 года назад
600rr with abs I do the same?
@motorcyclemaintenancechann2131
@motorcyclemaintenancechann2131 3 года назад
Yes, you do
@coolwicia
@coolwicia 3 года назад
@@motorcyclemaintenancechann2131 So why does the service book say that the abs pump is also venting?
@dacat8171
@dacat8171 9 месяцев назад
You apply too much torque to the bleed valves. It is 6 - 10 Nm. ☝🏿🧐
@giannispapadopoulos6603
@giannispapadopoulos6603 2 года назад
After warning everyone that the brake fluid is highly corrosive,you should check your swingarm and exhaust after the video.cause you CLEARLY spilled brake fluid there!and next time bleed the brake pumps too.wannabe mechanic...
@motorcyclemaintenancechann2131
We’ll try harder in upcoming videos. Thanks for watching!
@thagingerninjer5391
@thagingerninjer5391 Год назад
Why would you have to bleed anything, if you never let air in the system?
Далее
I Did This On A CBR 1000RR *NO ABS*
6:43
Просмотров 32 тыс.
Clutch tips you need to know!
7:42
Просмотров 22 тыс.
Coolant change on a 2013 CBR1000RR
22:26
Просмотров 31 тыс.
Brake Lines Bleed on CBR1000RR
7:56
Просмотров 1 тыс.
Honda CBR 1000rr - Radiator Fluid Change
15:02
Просмотров 23 тыс.