I published a time-lapse of this pond build and it was quite popular. This is a longer version with a vocal breakdown of the build. Plus footage of it 2 months after build. #Ponds #koi #goldfish #garden #diy
Nice pond you have there. I helped me mate build a pond a few years ago. It’s was a nice pond but he had a nightmare with Herons taking his fish so now it’s permanently covered with net which doesn’t look great.
Luckily I haven't had many issues. It's not great when you have to use a net. Looks awful. But those herons are like the terminator they just keep coming.
The decking that sits on top of sleepers overhangs about 10mm. The top of basket I just put 2 screws through the plastic and screw into decking so top of plastic pot is in line with top of decking. The pot hangs and leans against inside of pond sleeper at a slight angle. As plant is in water not to much weight and weight pivots towards pond wall. Done this with both ponds. Larger one has plants in there that are 4 years old and large. Seems to work. Not had any fall off. Get screws that are not prone to rust as will be in damp environment.
Sorry I think I misunderstood question. That plant hanging over side just does it naturally. I don't do anything with it. Does same thing on all 3 ponds I built as long as you attach to edge of pond.
4m x 4m mate. That gave plenty either side you can get away with smaller though if your careful. 1.5 m + 0.6 m for both sides is 2.7 m . So you could get away 3.5 m x 3.5 if they cut it for you to size.
Beautiful...... if possible can u plz share a cost breakdown of this pond ?? I think those sleepers r preety costly. Also how long does it took to cut them into proper size. I believe this is where most of the efforts r spent.
The sleepers were 200mm x 100mm x 2.4 m. At £22 each. Had to buy 12 of them. This was by far biggest expense. At around £270. I cut 6 at 1500mm and 6 at 1700mm as I did not overlap sleepers. It was hard work with a handsaw but cn be done. The 4 bits of decking on top only come to £32. Liner was a 4 x 4 m. It was a cheap one I didn't spend a lot. Think it was £55. Gravel 4 bags total £25. Hex screws were £20. Total £400. Pump and filter I already had. Along with plants. Pump is 3000 litre an hour. That cost around £70. 100 litre water butt, alfagrog, gravel, accessories for filter was probably £140 all in. Plants cost me £8 each in 1 litre pots. All in everything was probably £600-650. That's not taking into account any electrical. I'm electrician so do that all myself.
beautiful pond but i was thinking wouldnt it be good to have an overflow drain hole so if it rains a ton the fish wont escape from overflowing and keep the pond at a nice water level
I had an overflow on original sleeper pond and the water level was lower you could see liner. I didn't like it. I filled it in temp to see how it would go without one. Never had any issues. It tends to overflow evenly around pond under top decking. I kept an eye on it to check if water was getting behind liner. Never had fish get out. It doesn't seem to ever overflow over top of decking. It's what ever suits you. I'm new to this and adapt where I see an issue. They are very basic. As for water level I like it as high as possible. That's my preference. Not had issues with koi jumping out but I know you can.
Yes I agree staggering joints is stronger and I think advisable if you have bigger volume of water and going higher with sleepers. I prefer the look of how I did it and didn't feel pond volume was large enough to require staggered joints. This was a personal choice and your right it is advisable to stagger.
I got sleepers from travis perkins. I get a little discount because of trade. But I think they are about £22. You gotta pick the better ones out though as most are poor quality.
It depends on length of run. If there is already a power source in garden you can run off. More difficult if you have to run from fuseboard in house. To be honest I still not sorted that pond out properly. On extension lead 😩. Having experienced faulty pumps and heaters tripping electrics and causing everything to turn off I believe the best way is to have multiple rcds and setting it up so if say a pump fails and trips rcd you have second pump or airstones on separate rcd so you don't have total failure across your Pond. This is obviously more involved but safer for your Pond and fish.