No video :(

How To Calibrate Your Fuel Level Gauge To Any Fuel Sensor

Подписаться 10 тыс.

Просмотров 242 тыс.

50% 1

A step-by-step process on how to calibrate your Speedhut fuel level gauge to any fuel sensor, which includes fuel level gauge manual calibration and setting the full and empty conditions.
Shop Fuel Level Gauges: bit.ly/2JOuVdU
Questions or comments?
Email: Tech@Speedhut.com
Phone: 801-221-1460
SUBSCRIBE and FOLLOW
YT Subscribe: bit.ly/2g8tKb0
FB: / speedhut
IG: / speedhut
Website: Speedhut.com

Опубликовано:

28 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 31

@Hezath 3 года назад

This is such a great feature, took me a few minutes from start to finish looking at the existing sender and getting it reading accurate. Just awesome. Great gauges.

@ikebubins36 4 года назад

I Now understand why gas gauges are notoriously off. These gas gauges are using resistance or ohms. The float rides up and down a rheostat depending on the placement of the float the system will send a certain amount of voltage as a feedback. Many things can affect resistance this would be highly inaccurate. In industry measurements have to be accurate. We use a system of 4 to 20 milliamps as a feedback with a device called a transducer or load cell. With a resistant base system (ohms) I would suggest making sure all your electrical connections are corrosion free and tight. Re-strip the wires apply silicone dielectric grease reconnect them tightly. If you can pull out the float and spray it down with contact cleaner. Use non-combustible contact cleaner and make sure it's completely dry before you put it back in place. Good luck

@user-rk6pb9hk2d 3 месяца назад

Came looking for a gauge fix, not how to calibrate an aftermarket one.

@tousshong9438 6 лет назад

Great information. I recently replaced the gas gauge sending unit/sensor on my car but it still shows only show 7/8 full which is the same as it was before I replaced it. Do I needs to recalibrate the sending unit after the installation so it will read the correct level? Thank you!

@Speedhut 6 лет назад

Yes, you will need to calibrate the gauge to the sending unit.

@tousshong9438 6 лет назад

Thank you for your quick response. Why that important information wasn't posted on the material I got the sending unit from? LOL. Again thank you!

@vegasjack1 5 лет назад

@@tousshong9438 Because it was pretty obvious you would have to re calibrate it when replacing a sending unit.

@Hellsong89 5 лет назад

@@vegasjack1 Well if you replace old one with identical sending unit logic predicts it should work with out calibration as its same unit. How ever if its not, then you need to do the calibration obviously.

@vegasjack1 5 лет назад

@@Hellsong89 So, you don't think just disconnecting the wires to the same guage requires re-calibration? Let alone putting in a new one.

@awesomemodzzz6856 2 года назад

i got a samdo, im trying to set it where it reads correct, i have 3/4 tank of fuel how do i set this ? someone help me

@chupakabras3017 4 года назад

How about the test at the end of the calibration.

@chaimterrance7621 3 года назад

i know I'm quite off topic but does anyone know a good place to watch new tv shows online?

@jaxxgianni1008 3 года назад

@Chaim Terrance flixportal xD

@hungrynapps 2 года назад

Can I reset my guage from dashboard

@kalyangautam7345 5 лет назад

How to know sensor wire in fuel gauge using multimeter?

@muhammedmpower6673 3 года назад

Where can I buy it?

@Speedhut 2 года назад

Here are the Fuel Level gauges on our website: speedhut.com/categories/gauge-type/fuel-level-gauges.html

@whitemountain595 5 лет назад

I have 2016 Audi A6 V6 Quattro 11000 miles. Fuel range Gauge has incorrect reading. When I fill-up, it shows 490-510 mile which never happen. Dealer says that nothing wrong. I need some advise.

@Speedhut 5 лет назад

Give our tech team a call and we might be able to help you: 801-221-1460 or email Tech@Speedhut.com

@slideways2004 5 лет назад

@speedhut On the manual calibration, does the "full" have to be calibrated first?? I ask this because there is no way for me to empty my gas tank. Can I start the calibration with an empty tank on the E setting??

@Hellsong89 5 лет назад

I was thinking of the same thing. While its sure possible to calibrate gauge on the road side when gas runs out its still bit of a pain in the ass, where most people probably empty gas tank by driving short distances at home stead etc or in custom build have empty tank that has been in storage/been just made want to calibrate empty, fill up and calibrate full. Logically it should be possible to do ether way, but only speedhut can say for certain.

@Speedhut 5 лет назад

When doing a manual calibration on our fuel level gauge you don't need to calibrate full or empty an a specific order. You can do full first or empty first. You can also do them at separate times. Keep in mind that the gauge will not read accurate until both ends are calibrated.