HOW TO CONVERT ANY EF TO OBD1 | wiring up the d16z6 swap in the crx

Подписаться 6 тыс.

Просмотров 10 тыс.

50% 1

TONS of info packed into this video. sorry for the choppy feeling, i was learning a lot as we went along but as of today, Leo has traveled over 1000 miles on my harness.
but if this video can help anyone, i hope it keeps more crx’s and ef’s on the road!
@awd_nate
@crxsi_b52

Авто/Мото

Опубликовано:

24 окт 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 46

@roaninfisher14 3 года назад

You are a life saver, I've been putting off doing this because I'm scared of fucking up my wiring

@andruwwilson8367 3 года назад

This is honestly one of the best videos even on mpfi swap because I planned on doing my mpfi and obd1 swap at the same time

@jesuslewis7861 2 года назад

you prolly dont give a shit but does any of you know of a method to get back into an Instagram account?? I was stupid lost the login password. I love any tips you can offer me.

@edwardbronson1101 2 года назад

@Jesus Lewis Instablaster =)

@jesuslewis7861 2 года назад

@Edward Bronson thanks for your reply. I found the site on google and I'm in the hacking process atm. Looks like it's gonna take quite some time so I will reply here later when my account password hopefully is recovered.

@jesuslewis7861 2 года назад

@Edward Bronson It worked and I now got access to my account again. I am so happy:D Thank you so much, you saved my ass!

@edwardbronson1101 2 года назад

@Jesus Lewis you are welcome xD

@spoolinekrhdhulk-urban-c-w5709 2 года назад

Awesome making the jumper

@peterbryant3584 Год назад

Man pretty confusing but u got it I hate messing with wire great jod

@K26streetstroker 3 года назад

💪🏼💪🏼💪🏼💪🏼

@CEA-zw2xt 5 месяцев назад

Why do you have to get rid of the resistor box? Doesn’t that let you run low impedance injectors?

@alejandrovalenzuela5280 8 месяцев назад

Hey bro i got a question i been getting a 3 flash code check engine light wat can it be

@puch7261 8 месяцев назад

you dont have a write up on it anywheres im doing d16y8 need alittle info on harness.

@dickscrossedgarage 2 года назад

Sorry if I’m being hard headed, but if you’re removing the resistor box, why is it needed you have a MPFI harness? What are the other differences between a dpfi and mpfi harness? I’m in the process of d16y8 swapping an lx sedan and am a bit confused on the conversion process

@anotherefncrxvlog4350 2 года назад

you don’t need a mpfi harness, i only used the fuel injector plugs and wires simply to make it easier to keep nice and neat

@BRENDAJASON1 Год назад

The the obdo injectors are low impedance which requires the box and the obdo1 injector’s are high impedance which don’t require the box. I’m thinking that’s how it goes

@Cruz99juan 2 года назад

How did u converter the water temp sensor to obd1?

@anotherefncrxvlog4350 2 года назад

cut off the bullet connectors, extend wires to the thermostat housing, solder in the obd1 connector

@Cruz99juan 2 года назад

@@anotherefncrxvlog4350 thanks bro !

@anotherefncrxvlog4350 2 года назад

@@Cruz99juan yessir good luck!

@estebano2930 Год назад

@@anotherefncrxvlog4350 hey brother just got a 1988 crx si. With d16a6 with z6 head. Can't get the car to pass 4k rpms. Got a new dizzy

@larrypage9201 3 года назад

I also have a buddy that we put a k20a3 in and need help wiring it up too..never wired any hondas before.you should take a trip out here Kingman az and help us out

@projecthonda 3 года назад

Dude let’s work on something !

@anotherefncrxvlog4350 3 года назад

that’s all we do!

@alonzobonilla3548 2 года назад

What transmission did you end up using?

@alonzobonilla3548 2 года назад

Did you use the a6 tranny or z6??

@anotherefncrxvlog4350 2 года назад

crx transmission. the z6 trans is out of an eg and will not mount up / uses a hydraulic clutch

@MyKev1991 2 года назад

hello in your archives you have the electrical diagram for crx v-tec thank you

@anotherefncrxvlog4350 2 года назад

hi, i don’t but what issue are you dealing with? maybe i can help anyways…

@sergeibn6869 2 года назад

what ecu number you use? p08?

@anotherefncrxvlog4350 2 года назад

p06, it’s cheaper. if you chip, any obd1 ecu will do

@sergeibn6869 2 года назад

@@anotherefncrxvlog4350 can we chat by email. I need to ask you about my ef i beang build.

@boost_edjamesmathew2168 3 года назад

Are you Guys located in San Bernagucci

@anotherefncrxvlog4350 3 года назад

nope but we’re close!!

@boost_edjamesmathew2168 3 года назад

@@anotherefncrxvlog4350 That's cool I'm located in Phelan I have a Turbo D16 EF sedan and I work on EF's

@boost_edjamesmathew2168 3 года назад

@@anotherefncrxvlog4350 Do you guys go to the junkyard alot cause if you do maybe we can work out a deal I need the Integra rear trailing arm bushing inner mounting rods just the rods that go through the bushing and mount to the car I will give you some polyurethane energy suspension rear trailing arm bushings for a Civic

@boost_edjamesmathew2168 3 года назад

I take it your not interested

@anotherefncrxvlog4350 3 года назад

@@boost_edjamesmathew2168 we hit the yards a lot! this is just not a very good way to communicate with us, RU-vid doesn’t give notifications for comments i have to check the videos for them. if you dm me on Instagram we can talk more!

@boost_edjamesmathew2168 3 года назад

Do you have a Facebook account