How to diagnose Polaris UTV XP1000,XPT Turbo misfire codes 65590,65591,65592

Подписаться 1,6 тыс.

Просмотров 24 тыс.

50% 1

How to diagnose Polaris UTV misfire codes 65590,65591,65592 includes a proper sequence instead of just throwing parts at it to fix this common problem.
Polaris side x side misfire codes can be set because of several reasons, and if you're like me I would rather do some diagnosing first than throw hundreds of dollars at it hoping something solves the problem.
If you follow all these instruction you will know whether it is time to get your valves adjusted, or even if your current tune is causing this issue but I want to know my engine and clutch is sound before changing your tune because it could be a bandaid fix that is covering up something potentially very costly.
• Why Is My Polaris Rzr ... . RU-vid video for checking valve clearance
This link is and article I wrote about why there is only Ethanol free fuel going in my Polaris turbo fuel tank.
utvservice.com/polaris-utv-en...

Спорт

Опубликовано:

3 фев 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 13

@haraldhh3 Год назад

Thanks for posting! This is valuable info! :)

@utvservice Год назад

Glad it was helpful!

@vitotaverna 10 месяцев назад

My 900 is actually misfiring at throwing codes. Has fresh top end. And new head and Valves. Ran good for maybe 30 miles. Now runs terrible and spitting sputtering and popping. Has new fuel pump too. I’m lost!!! Maybe jumped a tooth I just don’t know. Thanks

@alexjrful 7 месяцев назад

Good morning I have a 2017 rzr xp4 that runs grate for about an hour after that it will go in to limp mode and have no power. After it cooled down it will run perfect agin any ideas of what the issue could be ?

@paulfrandin5730 Год назад

Thank you for this video. I've had my 2017 xp4 turbo for last 2 years and just recently on my last 2 trips I've gotten codes 35590 and 35991 my machine pops these codes after about hr of running the machine hard and I loose all power. I turn off machine wait a min and turn it back on and I have power again then drive about a mile and codes go away then about another hr or 2 I'll be fine before I repeat process. This is never happened to me until this year and was after I did my maintenance on it. Changed all fluids in machine new brakes new plugs cleaned out belt and clutch new s n b air filter. I do have an s n b air filter separator kit on machine and a blow hole for belt with a scoop going into the frogskin. I don't have the equipment u have but where do u think I should start?

@luisfortanel9618 4 месяца назад

Did u found the problem afterall?

@Modern_RZR 2 месяца назад

Update us Paul

@alexjrful 8 месяцев назад

How do u erase the check engine light ?

@kellydavis4954 Год назад

this is what i am looking for ,my 22 just got a check engine light when i was out yesterday ,once i find the problem how do you clear the light ? and below you say Most common problem is valve’s out of adjustment ,how do you know if its the valves ,is it noise or just from experience

@utvservice Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-y_5fLCWOFhs.html This is the video on how to check valve adjustment.

@jeffreyvandebogart8388 2 месяца назад

We were out for ride just cruzin 40 mph and started to lose power no light came on tell we got home 10 miles away. We be good for bit then lose power and always when I got up to 40mph. Throwing code 90 and 92