How To Fix a Dead Clutch Pedal

Подписаться 1,8 млн

Просмотров 538 тыс.

50% 1

My brother brought me his 2005 Honda Element. He said he had difficulty shifting it into gear. When I inspected it, I found the clutch pedal was on the floor, so he had no clutch at all. Further inspection revealed that the clutch master cylinder had failed.
In this video I show you, not only how to fix this issue, but also how to drive the vehicle just enough to get it to safety.
Thanks for watching!
#ETCGVideo #HondaElement #Clutch
Become a Premium Member of EricTheCarGuy.com: www.ericthecarguy.com/why-bec...
My Patreon Account: / ericthecarguy
The best place for answers to your automotive questions: www.ericthecarguy.com
EricTheCarGuy FAQ Page: www.ericthecarguy.com/faq/
Check out my ETCG1 channel: ru-vid.com?su...
Parts
Clutch Master: 46920-S7A-A05
Clutch Salve: (Perfection) 360125
Battery Lugs: www.amazon.com/Tsinglax-Batte...
Tools
Fluid Extractor: www.jbtools.com/john-dow-jdi-...
Line Wrenches: store.snapon.com/Open-End-and...
Antisieze Sticks: www.amazon.com/Loctite-38725-...
Lug Crimp Tool: www.amazon.com/Lincoln-Electr...
Related Videos
Replacing Clutch Hydraulics Honda Civic: • How To Replace Clutch ...
Replacing Clutch Hydraulics Acura CL (Honda Accord): • Replacing Clutch Hydra...
How a Clutch Works: • Learn How A Clutch Wor...
How To Diagnose a Bad Clutch: • How to Diagnose A Bad ...
How To Adjust a Cable Operated Clutch: • How To Adjust A Cable ...
How To Change Honda Manual Transmission Fluid: • How To Change Honda Ma...
Element Video Playlist: • I Just Bought 2 Honda ...
**Answers to your automotive questions found here: www.ericthecarguy.com/faq
Social Network Links
Facebook: EricTheCarGu...
Twitter: / ericthecarguy
Instagram: / ericthecarguy
Wanna see more stuff like this from ETCG? Information on Premium Membership: www.ericthecarguy.com/premium...
Stay Dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy®.

Авто/Мото

Опубликовано:

17 июн 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 390

@JoeCubicle 3 года назад

I have to confess I have not watched ETCG for a while but used to all the time, but, SO HAPPY to see him at 1.58 Million subs! I love seeing long-term RU-vidrs plugging away over years!

@ericthecarguy 3 года назад

Thanks for watching!

@darkone666alex 3 года назад

9:32 "I recommend cleaning it up before insertion. It should go in alot easier" - ETCG, 2021 All jokes aside, great video!

@JW--dc8ri 3 года назад

I was wondering who else would catch that

@fema_camper 3 года назад

I'm a gentleman... I clean up before AND after insertion! If I have a spill on the fender I always clean up after myself too.

@Watchyn_Yarwood 3 года назад

Gotta keep the 5th grade boys entertained!

@9800arturo 2 года назад

On my mother , thank you sir for still making videos !! Just watched two different videos that were uploaded 10 whole a** years apart. And now my clutchs fixed 😂🤟🏼🙏🏼

@jeffr0 3 года назад

I drove a bread truck for years. I’ve driven a whole bread route with a broken clutch cable by parking in granny-1st & using the starter to get it moving. Most people don’t know you can do that…but most people can’t drive a manual!

@DavidEdwards9801 2 года назад

The original Hybrid engine =)

@garydeandeery 2 года назад

I could change gear in my car with out pressing the clutch lol it’s just timing funny how we would drive when younger my mini had no fuel gauge so had to turn it off slammed the brakes to hear how much splash I could hear lol Or drive back home in the same gear lol

@labattsipa 3 года назад

As someone that has done this job on 07 accords.. My original broke the same way.. Blown out fastener. Replaced it with an autozone special that lasted 2 years.. Replaced again with the az special and failed again in 3 months.. Replaced again but with a genuine honda and all good again. That retainer U shaped clip is original by the way.

@aserta 3 года назад

This is nearly word for word how my uncle taught me to limp a dead clutch/clutch cable many years ago. :)) Neat.

@IBenZik 3 года назад

This reminds me of a night in Stetsonville, WI. Going to the in-laws middle of the night with the wife and kids and the hydraulic clutch won't work in my 1991 Pathfinder. Did the same thing to get us there and sure enough the slave cylinder was leaking like a sieve. That was under warranty. Got it replaced and it lasted until the truck was crushed at 260,000 miles Great video.

@carolb9422 3 года назад

Hi Eric. Had an 02 CRV stick. Replaced the master. Struggled to get the line completely purged then ran across in small print in the official Honda service manual something like:"if clutch is still out of adjustment after bleeding lines and adjusting master cylinder, place a wood block behind the slave cylinder to prevent movement then bleed the lines" . Shazzam - that was the problem: a tiny bubble of air would get downstream from the bleeder valve if the cylinder wasn't blocked when bleeding.

@fallingblock2900 8 месяцев назад

My clutch died on me tonight and I have been nonstop searching the Internet for help on what's wrong and how to fix it. While diagnosing it, I noticed that a part had a screw fail but I didn't know what the part was or if it was why my clutch failed. This video has almost the exact same engine and failure which made it so easy to understand. You are a life saver. Thank you.

@the_toppi 4 месяца назад

I'm glad you didn't resolve the problem and left it in. It was great to see you calmly explain next steps at a point where I'd be hucking auto parts across my lawn in frustration.

@NisSubieTechA 2 года назад

1:00 That is a great trick for anyone that drives a manual. When my clutch gave out on me in traffic, I was able put the car in gear with the engine off. This allowed me to limp the car off the main road into a nearby parking space and wait for a tow truck. Totally saved me from causing a huge traffic nightmare.

@Turtlefarm 2 года назад

Had a new clutch put in… changed the master and slave a month later.. since then I can’t get into first Gear or R from a stop.. if I rev the car while pressuring for 1st gear it will fall in.. or if I hold the pedal for 5-6 seconds it will fall into gear… I’m convinced it’s air in the system being introduced somehow.. but I’ve tried bleeding 101 different ways.. always seem to have air in the system.. never let the master empty.. garage wants a new clutch… I’m convinced it’s air… thoughts?

@garyanello3881 3 года назад

Very interesting to watch and learn but not attempt myself without pro guidance next to me. Hats off to you Eric, brave soul that you are!!!

@SuperDave21 3 года назад

I always enjoy your videos Eric, just to learn a little bit more. A guy can never know too much! Cheers, and Thank you !

@clintsearcy3252 3 года назад

I learned to drive stick without a clutch back in my old VW bug days. A vital skill.

@EngineeringVignettes 3 года назад

Had a clutch cable goes on my '82 Subaru. Downtown. Learned real fast how to start in first gear. Clutchless shifting was pretty easy and I was doing it prior to the failure anyways. A good skill to have if driving older vehicles... Cheers,

@mikedurnell 3 года назад

Back long ago Volkswagen had an automatic stick shift you can shift it but you didn't need a clutch I remember that as well My first learn to drive that way was in a wagon of Volkswagen wagon

@spacecat7247 3 года назад

@@mikedurnell yes the stick o matic. Friend had one. Kinda cool.

@tadams1767 2 года назад

Most Americans learned to drive without a clutch, as the majority drive automatic cars.

@delow5917 2 года назад

You’ll be buying a new clutch long before me.

@mygoodness8551 3 года назад

Great video, awesome production value! My clutch has a squeak, lubed everything, never knew about anti-sieze on the ball of the slave cylinder, gonna attack that now, thanks Eric!!!!!!

@arthurfricchione8119 3 года назад

Thanks for sharing Eric. Stay safe and well Artie 😊🙏

@thaik56 3 года назад

Wow didn't know the starter was powerful enough to start the engine in gear on the ground! Definitely useful. I damaged my strap when I used another car to tow the defective car even over a very short distance previously.

@mattfoley6082 3 года назад

As a DIYer I get vicarious satisfaction watching Eric use tools I'll never own but wish I did. So jealous!

@brianprice810 9 месяцев назад

only tech anyone needs to watch ! thanks for simple yet correct way to fix automobile failures!

@burnnotice5086 10 месяцев назад

This happened to me today on a road trip long distance. I forgot to check the clutch master cylinder fluid. It was empty no clutch. Almost panic. I filled it up. Pumped the clutch pedal with the engine running. Clutch action came back.

@BudTheDrummer 3 года назад

I think this was a fantastic video! I can't perform my own repairs anymore however, i love learning and I'm from the 60's. I've never had a hydraulic clutch so for me this video was very educational!

@mikedurnell 3 года назад

She was Eric I haven't seen you on here in a long time Glad to have you back

@channel_56_ 3 года назад

Hi Eric! I use a smaller version of one of those fluid extractors daily on Harleys and after i suck as much of the air out as it can, i release the vacuum from the tool line and then do another couple of old school bleedings. The tool doesn't suck all the air out all the time but is perfect to prime the hole system or to replace the fluid much faster.

@runderwo 3 года назад

9:30 "I recommend cleaning it up before insertion, it should go in a lot easier"

@morgangallowglass8668 3 года назад

Next time, ETCG gives us some barely legal clutch action! I am SOOOO buying that bleeder!

@JohnDowIndustriesInc 3 года назад

We know where you can find it ;)

@canuckfixit7722 3 года назад

I bled the clutch hydraulics in my '05 Element using the gravity-flow method. Worked great. Also, IMHO, the bare wire ground cable is to enhance flexibility of the wire in that area due to normal movement of the engine/transmission. Without such modification, the wire may break prematurely at the lug you just installed. New Honda ground cables are still sold thus way.

@tommyo9879 7 месяцев назад

Thanks Eric!, You just gave me the clue (at the end of the video)as to why I have an intermittent pedal problem, replaced the slave recently, the master a couple years ago. I know that at least one of the clutch springs is broken because of a knock during quick acceleration or gas on, gas off. thanks for the tip! getting a heavy duty clutch installed asap.

@Mathiaskbliss Год назад

I really like the video, I’m automobile student 💚

@subliminalvibes Год назад

Cheers and happy new year. I'm about to try this on my 97 EK hatch. Symptoms look the same. Barely made it home!

@JVHShack 3 года назад

Genuinely, thank you Eric for the tip on adjusting the clutch pedal. I will definitely check that when I get back into working on my Mazda B2000. Btw, the clutch master is really for a 1989 International S1700 dump truck and the slave is for a 1986 Toyota Supra. Did you ever think that would work? 😆 lol

@tezskanza 3 года назад

“Caution, very small writing..” Ha!!! Love it!

@LakshmananLM 3 года назад

Had this happen to me a few years ago. Did the same thing. Drove for a km to a workshop. Don't ever want that experience again. Didn't have the tools or the courage or knowledge to fix it myself.

@yardman0001 3 года назад

Had that problem many times with my RSX type s. Actually had one fail while bleeding it at the triangle diaphram piece. Switched to the civic EM1 clutch master (Oem) and never had that issue again. The em1 doesn't have that stupid triangle piece.

@jbar100 2 года назад

I had a similar problem with the clutch not disengaging. The shop I originally used to replace the clutch used a jobber throw of bearing and clutch and pressure plate of which the throw off bearing was a few mm's thinner than the British Leyland model, Cost $800 parts and labor and that was a lotta molla back then in the 70's. I removed that clutch 3 times myself after that ( MGB complete engine and gearbox out of car to do the clutch) and bought all new parts from Leyland to figure out what the problem was. After using all Leyland parts it worked just fine from there on.

@Zanbor59 3 года назад

Hi Eric, I noticed the remaining screw type is different than what's comes on the new one.... you are the BEST ..... Thank you

@HotQahwe Год назад

Great video! After driving stick for so long, idk why it took me so long to remember to turn it off before shifting after my pedal did the same. Thanks for the help

@Earth29431 3 года назад

Thanks for another video tips sir Eric, this video are very useful information.👍

@AntonioClaudioMichael 3 года назад

Very Nice fluid extractor Eric @EricTheCarGuy

@MaverickandStuff 3 года назад

Last summer my clutch cylinder went out on a trail at the bottom of a hill 3hr from home. That was a fun few days having to revmatch to shift.

@allmorales2990 3 месяца назад

I watch a few different vids on the same thing so I can learn more then one method cus some are better easier ways and this dude covers everything 👌I appreciate your knowledge 💯

@evewoodward5621 2 года назад

This is wonderfully clear and well explained.

@harvey1115 Год назад

This video just saved me a ton of time! Thank you sir!

@alexdubinsky6098 3 года назад

my 1980 Celica clutch used to stick... had to take the gear box apart twice to find the problem... in the end figured out the clutch plate the shop sold me was from a toyota corona, which is identical in all respects except the celica one has tiny grooves in it to release air locks. Replaced with the proper one, all came good...

@Crack84baby 3 года назад

Hey Eric! Love the vids!

@garyc.8488 3 года назад

IF it was a broken clutch disc torsion damper spring when you selected 1st or REV with the wheels on the ground that metal to metal contact makes noise. Screeching, rubbing and even a ticking sound. When you use vacuum to bleed to make it more effective wrap the threads of the bleed screw with Teflon tape, several turns. But no tape on the taper seat. The tape just creates a much better seal rather than air being pulled past the threads bypassing it's job. MC push rod adjustment is a critical part of setting these up. You want the piston seal just behind the port that feeds it fluid. If it's in front then it holds pressure and fluid cannot freely flow back and forth from MC to reservoir. Also the adjustment must allow the clutch pedal UP bump stop to be the pedal stop not the pushrod/piston/retaining clip of the MC. One easy way to check if the port is closed, remove reservoir cap, compress the pushrod of the SC and watch for the fluid level to rise in the reservoir. Fluid comes up, good. Doesn't come up, pushrod is adj too long.

@gentrymyler4038 Год назад

You saved me a tow bill with that lil trick, thank you🎉

@kenabi 3 года назад

i've got one of the like, 1.5L fluid extractors. truly, it simplifies one person fluid changing with bleeder valves. hook it up, loosen valve, gooooo. even for home gamers, these pneumatic fluid extractor/bleeders are just so handy.

@sunnyvale3231 3 года назад

I still love the popping/cracking sound of a bilt being broken free but not completely breaking lol.

@HotRod-wv4vm 3 года назад

Can’t wait to see your next video

@josephnorcalusa1710 2 года назад

Helpful information, thank you for sharing sir !

@miriamvivo4279 3 года назад

Always helpful , always learn somethin. Muchas gracias

@SinisterBlackShadow Год назад

Hey thanks for the video. Definitely some good info there. I actually had the spring come off of mine just as you had suspected here.

@bkj242 3 года назад

An Odessey with a clutch? No wonder it’s an “Oddity” thanks for posting. I had no idea a stick shift transmission was available for US purchase.

@miguelare3 3 года назад

That is a element

@Erik_Swiger 3 года назад

"How to fix a dead ...." perfect intro while I'm making dinner.

@JohnDowIndustriesInc 3 года назад

If you guys and gals need a quality fluid extractor, we have plenty of the one Eric uses, as well as two other sizes! #StayDirty

@scientist100 3 года назад

I do need one.

@billygerwig4352 2 года назад

Cant work on it font kno what im doin on a 96 ford explore

@bobdeengineer7396 Год назад

Hey Eric, love your videos. Just to add my Chevy Sonic F17 gearbox pedal went to the floor. Initially I thought i lost hydraulic but it was the two sheet metal screws that held the pedal to the assembly sheared off. Luckily I placed a crescent wrench behind the pedal body and worked until I was able to fix it. Pain in the neck to repair.

@staycurious3954 Год назад

WTF! Damn that’s some Bean counter’s doing right there!

@brotoriousone5735 10 месяцев назад

Very clean, I love my element 07 lx 5 speed I put 20mm hub spacers on it and 235 70`s on it. Looks great. The tires are flush with the fender

@JohnnyTalia 3 года назад

I noticed Eric had a little more trouble speaking than usual today "...sent me a test - text- last weekend...", "I'll be tapping - I'll be tackling that...". I know the feeling. Some days a lifetime of accumulated drain bamage just overrides your ability to cleak spearly.

@danhendershot8511 3 года назад

Dude I changed master and slave on my wife's 2005 Civic, and it's almost impossible to get all the air out of the line without removing the slave and line from the engine bay and hanging them up so all the air goes to the slave to bleed it. I spent 2 days with a vacuum assisted bleeder and it simply would not come out until I did this. Just hanging the slave up as high as possible, cracking the bleeder open, and applying some vacuum and the air literally came rushing out, reinstalled everything and I finally had a solid pedal. Just a heads up.

@ericthecarguy 3 года назад

If they were aftermarket parts I'm not surprised. I have more issues bleeding aftermarket parts than OE parts.

@danhendershot8511 3 года назад

Actually it was the way the line is ran, the parts are Exedy parts, and I have never had any problems with them before. The convoluted way they ran the clutch hardline from the factory makes it a royal bitch

@mushieslushie 3 года назад

I had this issue on my Subaru a few years ago and I replaced the slave myself and it also wasn't the issue. Replacing that was relatively easy on a Subaru, but once I removed it, it was pretty obvious that the lever it pushed against that went into the transmission had no spring retention. I ended up having the clutch replaced which cost me $1,600 but I don't particularly know if I needed that to be done or what the actual issue was.

@ryanpenner9131 Год назад

I’m having this same issue right now with my Subaru, the clutch fork has a lot of play and isn’t tight against the slave. Pulling the tranny out this weekend and hoping it’s just the bearing I need to fix or re-align it instead of replacing the clutch… wish me luck

@zacharywelvaert2235 3 года назад

That fluid extractor is kickass in a shop environment where you need to do that stuff alot and have shop air. There are cheap ($20-30) manual handheld ones on Amazon or at harbor freight that work just as well for quicker jobs and/or DIYers

@JohnDowIndustriesInc 3 года назад

Our fluid extractors are pretty awesome!

@AntonioClaudioMichael 3 года назад

Good video Eric @EricTheCarGuy

@DidiLeeReco 3 года назад

Great video mister Eric.

@pauljo9441 3 года назад

Glad your in your element ⛅great tip as usual 🤷‍♂️🤔

@katanamd 3 года назад

So when this video came out I opened it up but didn't watch it. Little did I know but the day after this video came out my slave cylinder would die on the parkway leaving me stuck on the shoulder (After floating gears down the highway for a few miles trying to get off to local roads). I wound up changing it on the shoulder (Had the part on me as I was on the way to change it). I bled it well enough on my own that I was able to at least get off the highway.

@donkaiser6704 3 года назад

There should be a spec on the clutch slave cylinder travel. You might check that you are getting full slave travel before going to the trouble of pulling the trans....

@ericthecarguy 3 года назад

I'm pretty sure I'm getting full travel based on the feedback I'm getting from the clutch action. I've seen this before with Honda clutches, spring failure. I'll find out for sure when I take the transmission out. Thanks for the comment.

@benali6929 2 года назад

Always great to see u man, gray hairs but rocking

@palitopolo232 3 года назад

Thanks eric for the new videos.

@ericthecarguy 3 года назад

Thanks for the comment.

@christopherdudley1585 3 года назад

You might also have too much air in the master cylinder. If you leave the vehicle tipped upward overnight the air bubbles should come to the breather valve.

@ericthecarguy 3 года назад

I don't think that's the issue, especially after bleeding a second time. I'm almost positive there is an issue with the clutch that I hope to cover in a future video. Thanks for the comment.

@rpehlman135 Год назад

Beautiful. Thanks. Gettin ready to do that

@user-gs3zg1du7v 13 дней назад

No b******* and straight to the point. This is what makes good clips......nice shop also

@sjay149 3 года назад

I replaced my slave, but I injected fluid in to its bleeder, had someone work the clutch pedal, until the reservoir was full. I used a new 2 qt old fashioned oil can. No air issues.

@Daniel-zr9xq Год назад

Merci infiniment Eric,vraiment merveilleux -belle annee 2023.

@ua7pyro591 3 года назад

Happy Friday!!!

@ericthecarguy 3 года назад

Happy Friday!

@AntonioClaudioMichael 3 года назад

That pin on the fitting looks like a construction staple @EricTheCarGuy

@oscarleite7109 3 года назад

Eric, that’s funny you are worried with the DOT3 fluid not to be spilled on the paint cause it will “eat it” while covering the holes of the pump containing fluid with your fingers without gloves! (no criticism… I often do the same while bleeding my bike’s brakes 😊). I love your videos!

@codo7 3 года назад

Thank you, Etcg.

@LegoDork 3 года назад

A lot of clutch slaves have the bleeder below the line. I've had some luck unbolting the slave, getting the bleeder above the line, and pushing the piston in manually with the bleeder open. Sometimes just cracking the bleeder and pushing the piston in will do the trick as well.

@jamesterrill1938 3 года назад

good video, Honda products are friendly to the mechanics...

@mikedurnell 3 года назад

That was supposed to say gee whiz anyway glad to see you back on here

@ericthecarguy 3 года назад

Thanks for that. However, I never left. You're just not getting notifications unfortunately. Me and the algorithm don't get along.

@user-lp7fz8fs8e 2 года назад

Thanks a lot. Learned alot.

@2jays878 Год назад

Awesome video Eric! Long time viewer here. I just leveled up to Acura, and the J series has the same transmission as this I believe. I have a 6 speed TL, and my master was installed incorrectly. The mounting bracket split in two pieces, so I found a spare pedal. I know there's an adjustment on the master itself, but also on the pedal..? ANY way you could help? I've seen 1 video, on a kseties but seemed very specific to that make and model.

@Sheesh_Pickup 3 года назад

Youre the best Eric.. learn new crap everytime

@paulrooster2108 3 года назад

I use to love being a Mechanic till they started making cars smaller an smaller an adding more an more crap under the hood an then back in the late 70's -80's there was 20 miles of lil plastic vacuum lines going everywhere , We had a lil guy in the shop we would hang him by his ankles in some places to get to certain parts myself being 6ft 3 an 250 lbs there was some places I just didn't fit you know like having to have over 2 feet of extensions with a wobble socket on the end -- ok I'm IN an Locked - oh damn it slipped LOL , So In the 90's moved over to Heavy Equipment, while true there were a few wrench's that were damn near 3 feet long an heavy AF , Sockets that you needed both hands to pick up but it was a trade off , the electronic I really didn't mind as I sorta grew with the industry on that aspect of it an most of the ole timers just didn't want to learn the new systems,

@ua7pyro591 3 года назад

I used excedy steel lines and master/slave. It's been great!

@ericthecarguy 3 года назад

They make great stuff.

@gavinmullet688 3 года назад

+1 for those excedy parts. They’ve been great in my ep3

@billygerwig4352 2 года назад

No petle

@billygerwig4352 2 года назад

Will u have to move treans?

@fire7765 3 года назад

Great job

@Claustropbaoeia 2 года назад

Great video tyvm!

@vijayantgovender2045 3 года назад

Thank you Eric I only have one question for the most of the time you never had on gloves thank you for your wonderful videos I am from South Africa please do a fellow up video getting the Honda fixed I am from South Africa

@ericthecarguy 3 года назад

Hello South Africa. My plan is to do the clutch and make a video of what I find. Thanks for the comment.

@yasmanibarajas7278 3 года назад

I have an issue with the actuators but my vw mk3 is very different. I can't seem to find videos that cover my car since it's very old but I take in all the tips and tricks as I can.

@ericthecarguy 3 года назад

Check out my friend HumbleMechanic. ru-vid.com

@dojmike 3 года назад

I had a clutch pedal on the floor and it was not the hydraulics - it was a broken pivot ball bolt.

@hobe5143 3 года назад

You should try this on a civic there is even less access. The original Honda part failed the same way. The replacement lasted a week then did the same thing. We ended up replacing master, slave, and flex line.

@jameydepriest9479 3 года назад

Hey Eric, Did you have to clean out the brake fluid from the fluid extractor to prevent the seals from any damage the brake fluid could cause?

@juhdah2146 Год назад

Still a great lesson, which l will have to tackle. I don’t see the banjo bolt as part of the bleeder valve system, l suppose bleed it at the same time?

@danielblum9215 2 года назад

Great and very helpful video. I have a problem changing gears on cold mornings but it goes away if I turn the key off or let the engine warm up. One certified mechanic thinks it's the (extremely old) clutch. another wants to replace the master and slave (for the third time). Does anyone have a clue on which way to go?

@rebepalma2430 Месяц назад

Have the same problem right now too 😅on my civic si 2006 the guy changed it 3 times keeps breaking & my clutch is almost new

@frankp.2831 3 года назад

Eric, have you tried reverse pressure bleeding the circuit? I had to do that on a couple of cars (BMW’s) without a master cylinder or pedal return spring. Impossible to bleed otherwise because they used the pressure plate spring to return the clutch pedal to the up position. I used an oiler can which I cleaned out meticulously using brake cleaner and now keep exclusively for brake fluid.

@ericthecarguy 3 года назад

That's funny because I cut out a line in the video where I said the best method to bleed a clutch is pressure bleeding. After using the fluid extractor I decided to remove that quote. Thanks for the comment.

@thaddeuskwasnik120 3 года назад

Anytime I have tried bleeding a brake or clutch system with a fluid extractor I have found that it will pull air from the threads around the bleeder screw itself. This will make it impossible to evacuate all the air out of the system as it is picking up air from the least restrictive place. To correct this, I remove the bleeder screw completely and apply a heavy coating of thick grease to the threads and then thread it back in. the grease act as a temporary sealant which allows the suction tool to apply full suction to the system

@ericthecarguy 3 года назад

That's a great tip. Thanks.

@mdargusch 10 месяцев назад

What about contamination from the grease?

@matthk 9 месяцев назад

@@mdarguschuse silicon paste instead

@Bobherry 3 года назад

Notification squad!!! FIRST!!

@Erteywie 3 года назад

My '97 s10 5 speed had a little plastic connector/bearing that linked the clutch pedal to the master(slave?) and fell to the floor. took a while to diagnose it, but ultimately was a $2 fix.