How to Increase the Charging Current of the Parkside 4.5A Charger up to 5.6A

Подписаться 393 тыс.

Просмотров 37 тыс.

50% 1

#ErCanEverything #Parkside #Modification
🔸In this video I will increase the charging current of the Parkside 4.5A charger up to 5.6A and will add a slow charge function for those who love their batteries🙂
🔥You can find the featured products here👇
📌20 AWG Soft silicone wire s.click.aliexp...
📌KCD1 Rocker Switch 15 x 21mm s.click.aliexp...
📌Clamp Meter UNI-T UT210E s.click.aliexp...
📌InfiRay P2 Pro Thermal Camera s.click.aliexp...
📌GVDA 3 in 1 Digital Oscilloscope Multimeter s.click.aliexp...

Хобби

Опубликовано:

21 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 50

@giuseppezaza6985 6 месяцев назад

the hack is good but more current is not always a best way to charge a battery. Lower current is good 😉😉

@ErCanEverything 6 месяцев назад

That why there are 3 option switch😉

@ΣΤΑΥΡΟΣΓΚΕΡΛΕΣ 5 месяцев назад

This has become my favorite video. Can't watch it enough.

@antonioc7735 10 месяцев назад

Sarebbe bello vedere più precisamente i collegamenti finali che hai fatto, ma l idea è geniale!

@ErCanEverything 10 месяцев назад

I showed you everything in detail but maybe I confused you because I showed the other side of the board but I didn't make any changes there. All the work is in the resistors🙂

@FixitEasyDIY 10 месяцев назад

This is a simple and effective hack ❤

@ErCanEverything 10 месяцев назад

It's really easy my Friend, but you shouldn't overdo it like I did in the first attempt😁

@frabrf 6 месяцев назад

thank you for this video. a question is it better to charge a battery with a low charging current. example 2.4A instead of 4.5A.

@ΣΤΑΥΡΟΣΓΚΕΡΛΕΣ 5 месяцев назад

It depends on the AH of the battery your are trying to charge. If you charge the 8ah battery,than obviously the 5,6 setting won't do any harm because it is below the ah of the battery. If however you try the 5,6 setting to a 2ah battery, you have a higher risk of ruining the battery in the long run. In general charging amperage should be half of the ah of the battery.

@frabrf 4 месяца назад

@@ΣΤΑΥΡΟΣΓΚΕΡΛΕΣ Thank you for this valuable information

@robbyt.5258 2 месяца назад

Basically yes. The slower the better. If you want the battery to be full again quickly, just charge it quickly.

@ΣΤΑΥΡΟΣΓΚΕΡΛΕΣ 10 месяцев назад

I have a parkside double charger that one slot is not charging nor does it light up. I admire your work. Can you please advice as what should I check? Fuse seems OK by measuring it.

@ErCanEverything 9 месяцев назад

Measure the voltage across the capacitor after the transformer. It should be around 21.6V. If there is no voltage in the capacitor, it may be the transistor in the primary coil of the transformer.

@ΣΤΑΥΡΟΣΓΚΕΡΛΕΣ 9 месяцев назад

@ErCanEverything hello again. I've measured both sides the negative and positive and both show the same voltage of 4,6v(without battery connected). Once connected the working side pumps up to 20,4v but the other side doesn't. I assume there must be a problem with the third pin of the connector the ID,thermal pin.

@juanrodriguez3165 10 месяцев назад

So you could also alternatively cut one end of one of the resistors and put a switch and select 2a and 4.5a? Thanks for the video and the idea.

@ErCanEverything 10 месяцев назад

Exactly, but if you decide to add a resistor you need to keep an eye on the temperatures and I don't recommend going above 5.5A

@juanrodriguez3165 10 месяцев назад

@@ErCanEverything That's precisely why I said it, my intention is to leave it as it is, with the same resistors that it comes with, I just wanted to have the possibility of charging 2ah and 4ah batteries with just one switch, thank you very much friend for your answer.

@kocetoMR 10 месяцев назад

this is a very high current for these Chinese battery,even 4.2A is a lot. 0:02

@juanrodriguez3165 10 месяцев назад

@@kocetoMR The original charger already charges at 4.5ah for 4ah batteries, perhaps it is bad to charge lithium batteries at 1c but the factory charger already charges at 4.5ah for 4ah batteries, it would be good to put a switch and have the possibility of charging at 2ah for 2ah batteries.

@ΣΤΑΥΡΟΣΓΚΕΡΛΕΣ 10 месяцев назад

@juanrodriguez3165 you should do the same with the older charger that is just 2.4 amps. A switch that can boost it to 4.5

@szatanizmo 7 месяцев назад

engineers: let's make it safe and limit the current. This guy: who cares if my shed goes on fire

@tehnoelektronikloznica7119 10 месяцев назад

Why should I doing this? It is much better to have 2 battery instead to have not so faster charger.

@zapanjormas4787 7 месяцев назад

yes, for the battery sake, and charger too

@DjaniAgain 10 месяцев назад

As always, great job Brother!

@ErCanEverything 10 месяцев назад

Thank you Brother🙂🤝❤️

@vinniethapower 9 месяцев назад

Very good video! I have the older 2.4A charger, but its different from this one, you know how to do this on the older charger? I have 5 of them, i am willing to risk modifying one

@robfel68 10 месяцев назад

Nice video brate. Everything with Parkside Batteries makes life more easy. Greetings from 💛💙💛💙💛💙

@KlopsMielony 5 месяцев назад

Great job!🎉

@AAAlexAlex 4 месяца назад

Сгорели Q5, Q6 , как они называются?

@nursaitaksu-yt1nr 10 месяцев назад

👍👍👍👍👍

@scania161616 5 месяцев назад

This is only 0.1 Ohm ?

@adem335i8 10 месяцев назад

Is this also possible with the 2.4amp charger?

@ErCanEverything 10 месяцев назад

Maybe, but 2.4A and 3.5A don't have a fan and will heat up a lot, they might even get damaged.

@zapanjormas4787 7 месяцев назад

@@ErCanEverything damaged like the 4.5A with your 5.6A mod. same thing with the battery, and the gain of charging time is very limited. Note also charging 8Ah battery on theses charger are not very recommended, as the charging time (and the time where the charger will heat) is doubled vs 4Ah.