I've watched a lot of home improvement videos guys, and I have to say, by a long way, yours are the best; well thought out, show lots of tips and tricks and methodically do the job. Well done guys 👍
Yeah, I’ve got to admit hats off to these brothers. I’m a Qualified Plumber qualified Gas Engineer, qualified F gas qualified electrician and these guys have shown me a few tricks no doubt. ❤
I had a new kitchen fitted (moved house) but didn't have the time to watch it being done. Excellent to see it done and didn't realize how much care is involved in adjustments and how uneven the walls can be. The workmen even had to replace some of the subfloor and floorboards due to some water damage (nasty surprise), underneath the old cabinets (prior people must have masked the damage with a new shelf and paint).
By far the best kitchen fitting Video out there and I have watched a lot US included, just right coverage on all sections. Only thing I would add before drilling holes in walls, check with a stud and cable finder there are no cables or plumbing behind where you are putting your fixings. If there cables or plumbing pipes you will need to move the fixing point or method of fixing. Nothing worse that water going everywhere on your new kitchen or bang and power goes out. Check you know where the stopcock is and it works! Plus where the fuse board is. Great Video 👍.
I am also an intirior designer in kenya..i do kichen cabinets and wardrobes and i love your videos..💥i am watching your videos to see if i can learn something new..keep up with the good work
Saw you guys mainly on shorts videos with quick tips and tricks and wondered if you did full videos. I'm glad you do and happy I found the channel, great stuff and I've just subscribed :)
Great to see you sharing your work with others. We have developed some strong fastenings to assist with kitchen installations. I would be interested in your feedback. Plinth Lock would look cool on this kitchen installation. Are you aware of the product?
Very detailed and helpful, brilliant as always Brad and you too Phil. You all work so hard to do these videos and I look forward to watching each one 😊 Keep up the hard work
Thank you so much! You guys have got a great team obviously..! Very clear, very thorough, very helpful.. and you guys are fucking cool too. Top marks boys! 👌
At the 18 minute mark when you screwed your brackets into the wall. Did you get lucky and have framing (Stud/dwang/nog) in the wall to fix to or is that only into the plaster wall?
Love the video guys very detailed and helps alot 👍🏼 question the cornise u fitted which way up did u put it as its got the triangle 🔺️ bit on the end and does it matter ? as I doing my mom's Wicks shaker kitchen and it looks the same as what you guys fitted , any help would be great 👍🏼 thanks
Thanks 🤩 With those best to look at drawings there’s a few styles some have shadow gaps some go inside end panels some under so drawings can help with that 😊
Fantastic vid. Really helpful. Question regarding plinth board. Looked like the floor was not installed yet. Should you leave the plinth untill the floor is finished? If its tiled the tile would go right up to the feet of units?
You've got to factor in the floor height. Normally leave a small gap between edge of floor and the legs to allow for expansion (if not using tiles) then add plinth after to hide any gaps.
3:00 after flipping the cabinet, the right side and left side feet will switch their positions, and you will end up with a tilted cabinet. To fix this, after leveling you first need to switch the legs from left to right and vice versa, and only then flip the cabinet.
maybe you can tell me if this sounds possible I thought I found the stud using the stud finder not quite sure what happened but the screws may not have been quite the right size I mounted a fire extinguisher bracket what the end product was is maybe the screws were not the right size so it seem the remedy I came up with is I tried to use 3 washers and put the screw through into an anchor any ideas please thank you it does seem secure does that sound like it is a possilbe remedy put the screw through 3 washers into anchor does that sound right ? thoughts please thank you! ( in case I was unclear I installed a fire extingusiher bracket tried to do it by putting screws through 3 washers for each screw in to anchor ) does that sound possilble ? thoughts please thank you!
Guys I need to talk to you. Do you have a no. To contact. I watch your videos and follow.you. i have bought a house which needs renovation and.need suggestions and possibly some.builder.
Surely the bottom level is more important.. more visible.. There might be a slight variation in the size of the cabinets so best to hire that up high..