Using your foot introduces all sorts of debris, and even laying the insert on the tire and cardboard does the same. To decrease any chance of picking of grains of sand (greater friction), I treat mousse installation like surgery. Also, Ill smooth any rough areas inside of the tire with a rasp and then with damp rag wipe and allow to dry out.
I do the exact same thing with my RMATV Tusk bench-mounted stand as a legit compromise that works well, not the floor stand, I use the one without legs, the one that can be mounted or affixed to a workbench. My workbench is fastened to the wall studs so nothing is moving when I apply leverage. Good luck 👍 If Santa is reading, I do want a Rabaconda for Christmas 2022 🙏.
Just done it. Mate, you make it look a lot easier than it is for a mousse virgin. But it is doable even though I genuinely thought I'd snap the bead wire. I seemed to use a lot more brute force than you did. Maybe next time I'll be a bit less of an oaf. Still took me an hour. Even with a Rabaconda. And loads of lube.
I got 3 flat tires with non-repairable holes with tubliss within 6 hours of riding, and start considering mousse. But gosh this is looking so freaking hard
We've used them all for racing out here in desert, woods and track at NHHA, WORCS, Vegas to Reno, West Hare Scrambles. We have tried all 3 of the "big brands" Michelin, Nitro and Dunlop and here is my $.02. First off, you can't use enough lube. We used the lubes that come with the mousses and those little tubes are not enough. I use 3/4 on a tube in the tire and about 1/2 a tube on the mousse (particularly the rear). WE used Murphy's tire soap as well as the stuf from Zip-Ty racing which is like Murphy's. Just hated the mess when changing so we went back to Nitromousse cooling gel. I liked the the nitro concept it had a progressive feel and was generally true to size. The issue was inconsistent manufacturing which could have been a result of COVID, but I felt they shrunk too quickly especially as my son got faster (he was running B super mini when we started using them and then up through B250). Durability was good though and feel was good. It just sucked not being able to get more than a 2 hour race out of them before having to cut and stuff. Nitro's are probably best for weekend trail riding guys that don't want to risk a flat in the woods. teh lower speeds will keep these from blistering or shrinking. We then went to use Dunlop and Michelin. I liked the Dunlop sizing as we also use Dunlop tires. The mousse had good feel and definitely held up well. The only issue is it didn't seem to rebound as well as the Michelin. Meaning, after a couple rides, they shrink, so you take them out and put them in the sun for a few hours and they will expand back out, sometimes quite significantly, to the point you cant see where the bead lock was. Anyway, really liked Dunlop, but just couldn't get as much life out of them before needing to cut and stuff. That said, far better than the Nitros'. Finally Michelin. Man they can last 3-4 race tires at least and depending on the race. We probably get 15-20 hours out of a rear mousse. Now I will say that because of desert racing we can get away with higher pressures, so I will use a 140/80-18" mousse in a 11/100-18" tire. It is a bitch getting it in there. However, once the mousse breaks in, it will last at least 3 races and then a couple more practice tire changes. Big fan of the Michelin!
So let me get this straight. I need $300 worth of tire irons to install a $120 mousse that will only last 6 months max? I'll go TUbliss or stick to regular tubes thanks.
no,but seriously,what psi?I've been trying to put air in it and finally my tire blew a bead,almost lost my ear-sight ,week later,I still have ringing in my ears!!!!!
Love my Rabaconda, but damn can they make it taller? All that bending over hurts my back when I'm doing more than one mousse. And reality is, if you're buying a Rabaconda, you're typically doing more than one wheel!
You could, but they’re not DOT approved. Also, highway miles will wear them out really fast. Like he said in the video, heat is the enemy. High speeds generate a lot of heat and they will break down very rapidly. Also, you can’t air them up, so you may not like the lower pressure feeling especially while cornering.
Either stick a tubeless valve in or one cut from an old inner tube. You can use that to blow compressed air in to push a tyre up onto the rim that hasn't set on the rim all the way around. Take the core out to increase air flow.
@@martincooke6230 Electrical tape over the hole works just fine or RMATV sells little rubber plugs that are great. They seem softer than the Tubliss plugs.Tried the old valve stem thing and did not like it but I also have issues sometimes getting enough air pressure to push the bead out on a older mousse. Maybe I need to revisit!
@@SHAPI84 I have found problem occasionally when pressuring tyre up onto the rim. You can lose a lot of pressure around the rim lock bolt. Take the nut off and slip on a suitably sized rubber grommet and replace nut finger tight. That solves the problem for me. Don't forget to remove the grommet and tighten the nut down afterwards :)
Nope, breaks down and dissipates eventually. A lot of shops will use tire soap/lube, as it withstands the heat and last a good long time. Though a reapplication with the included Michelin lube every few months isn't a bad idea.
Now when you say heat breaks it down is this not a good option for me here in Haiti? 90-100 degrees every day and have to hit street sections to connect trails.
As long as you slow down a bit on the paved roads you'll be fine. I live in the tropics and use mousse with no problems. If Haiti is anything like Cambodia ,you probably get a lot of nails in your tires.
I imagine the heat from higher speed street use would wear the mousse out pretty quick. Tubliss isn't DOT approved but is probably a better choice if clocking some miles on pavement
ADVRX these can not be used on the street because they will get hot and self destruct. I have run tubliss for years and love them both on and off road. they last pretty much forever also.
The Moto fixery thank your for your input. I would love to be able to carry a plug kit instead of tubes off road. Where I live I have not found any one that uses the tubliss kit. May I ask what size tires you are running?
ADVRX i run tubliss on my ktm 500 xc-w using Pirelli scorpion mx extra x 80-100-21 front and kenda trackmaster 2 120-100-18 rear. also on my wifes honda crf 230l using the same front and a trackmaster 2 100-100-18 rear. tubliss have a tendency to leak very slowly so I use "stans" tube less leak sealer because its not messy like slime would be and it seals everything right up perfect and absolutely no mess when you go to change tires later. stans is a product designed for mountain bike tubeless systems and is easy to find and use. I also carry a plug kit in my riding pack but it is easily possible to ride with a completely flat tire using tubliss. some people actually do intentionally to improve traction. I run 17 psi give or take on the highway and 5-10 for trails here in rocky steep Colorado. tubliss gives the sidewall of the tire some rigidity while allowing the middle where the tread is to flex and conform to the trail and also making the trail less bumpy because the tire is absorbing some of the bumps adding stability and traction.
@@RyderLost Without the rim lock the rim will spin but the tire may not, particularly on the rear wheel. You need something to keep the rim and tire connected beyond the friction between the tire, mousse and rim. Some run two rim locks as the extra traction given with a softer tire and without the associate air pressure pushing out on the tire sides and rim lip let the rim spin inside the tire.
@@thegan9143 When we run Vegas to Reno we do not use a rim lock. At higher speeds it unbalances the wheel. Never had an issue with spin. That said for all of our other races we will run only one and typically not an issue
@@SHAPI84 For the desert runs are you using a firmer mousse to take the heat of high speeds? I'm more familiar with low speed technical where traction is maximised by running a soft mousse, some even drill them out to get a feeling of under 4-6 psi. Running double rim lock keeps the tire locked to the rim and perhaps they offset one another for balance? I've only every run one but have friends that run two like the pros I guess lol.
Make sure they are always lubed, when not using the bike, make sure there is no weight on the wheels as this can cause memory flat spots, put it up on a stand off the floor, I get nearly a year out of mine by looking after them.
Also, put valves in the rims, this stops water & crap getting in & washing all of the lube out & you can also use an airline & pump to seat the bead correctly.
My buddy got 2 full seasons out of a set. Keep them lubed and they will last. He changes tires a lot for different terrains, and they don’t have any ware. Bibs are the way to go.
I wish they'd make one for peeps like me, who want a longer-lasting, higher-pressure version. I don't want it for competition, just to avoid having to change tubes when far from home in the boonies. These things are too soft to use on the road, which is 70% of my riding
I have to have another set of hands and 8 irons. Now, in my defense we were building wheels for Vegas to Reno and using a 140/80-18 mousse into a 110/100-18 D756 Dunlop with very stiff sidewalls.