How To Install C10 and C12 Cat Injectors. Removal, Install, and Adjust Injectors. 

Excellent video. Wish one can actually buy a compilation of your videos

just wanted to say thank you, very helpful for my new old semi truck with a c12 .. when I get it together im gonna be sure and send some money to the paypal

Amigo muchas gracias por tan valiosa informacion y a la vez por tan ilustrativo video que me ayudo mucho en un caterpillar c10. Saludos desde el ECUADOR y sigue adelante. GRACIAS

Another great video. Thanks! I know you mentioned to make sure and check that push-rods are straight, since at this point, we have them in our hands anyway. Which of course is a very good practice, but how do you check them closely, other than a visual? We keep a clear pane of glass here in one of the tool boxes. When we are ready to check a push-rod, we grab the glass piece, give it a quick cleaning, and apply a little puddle of new oil onto it. Then we lay the push-rod onto the oily spot on the glass, and roll it around. While looking up underneath at its contact pattern against the glass. This shows us even the most minor of bends. I also see that this engine is pretty dirty. I personally would spend more energy than I'd like, worrying about some clump of dirt getting into the engine during this repair. Our practice here is to power wash off the engine with soap and hot water, before such a repair. Is this an option for you guys in the shop, and then just include that charge to the customer? We don't always do all of our own work here, and sometimes take one of the Trucks to another shop for some work. When this is the case, and we have a very nice power washer here, we always give the engine, or transmission, a good washing before we bring it in. It gives me peace of mind! : - )

excelente vídeo 👍

Awesome job

Great work

cool,had to watch. I drive a c12. thx

Hello. Your videos are great! I am trying to fix a few issues on my c10. It misses for a few seconds on start up and is over fueling at idle. It clears up when you run it down the road and idles clean for around 15 minutes then runs rich again until you run down the road. I was going to have all 6 injectors tested but when I pulled them out several had broken middle o rings. All lowers were carbon and deteriorating as you described. My question is could the broken o rings be causing this by themselves?? Tia.

EXELENTE!!!

Very good job

Respect man up

Very good

great video can you do a injector trimming video pls

رائع انا اعشق ماكنه كتربلرc12

Adept Ape can you make a video on how to program injectors on C15. Question are perkins diesel engines the same as CAT engines, can we use the Cat adapter 3 on the perkins engines thank you.

Hi how you doing I was wondering if there is a video that shows how to take off a timing cover for 3176 cat if there if please help

Live you sir

Love your videos your a real knowledgeable fellow I got a question Why do you think a c12 would break a rocker pedastal I just did the cam and followers last year Drivers are just learning to drive would it be possible it was an over rev situation ? Just want to repair it properly is all Thanks for any info

Hi. Friend I need know How can i Calibrate the valves for c12 engine?

Dears I have great problems in many cat C32 roller of arm rocker blocked no turned who damaged crankshaft. Are see this .

👍

I may like to see, video of model c 12. 2ks68748 valve ajustment and injector calviration.

Can you use a hex bit socket (15mm?) and ratchet to turn the engine?

9:05 WARNING!! Those electrical connections are VERY easy to over tighten and break the studs. Tighten them very lightly with a quarter drive ratchet. I mean Very lightly. I broke one off and had to swap the yellow part off another injector, which thankfully wasn't a hard task.

How much should this cost to do? I have a c12 that's running good but kind of weak. Was told it needs injectors when I bought the truck but I never got them and started hauling. Now that I've bought a 2nd truck I want to get the c12 in better condition for a driver

Can you do a video on the 3176?

@Adapt Ape. Do you need to input the serial numbers of the injectors in to Ecm? I have been told that's the case. Do you know if that correct of not?

Cuáles son los torques por favor

What size where the hold down bolts?

I'm having a hard time finding the injector hold down bolts. Where can I find them for a C13? Also what will happen if I don't set the intake and exhaust heights and just torque the bolts?

How about doing a How to, 3406C fuel injection pump R&R with timing it.

How TO fix ABS PROBLEMS

Hi, sir, I'm Jonathan magturtur, and presently work here in Saudi Arabia, as a engine overhauling mechanic, and the engine that I overhaul is c11 and c13 . And may I ask a question sir? Could we start that engine with out the panel board from its body pay loader? As we testing first befor installing to its body pay loader? Please sir, gave me your advice here. Thank you.

Assist for c 13 cylinder head bolts torque and rocker bolts torque Or Torque specs pdf for C13 DH402038

Wouldn't that be HEUI? Fuel filled head at like 6, 8, 12 PSI and the electric injection type? Or does HEUI not have a 'piston pump' inside the injector when it comes up from the spring to suck up the fuel into it then it gets pushed down to inject? I think I somehow found a way to confuse myself, again. Or is there a difference between EUI and HEUI? Anyways, Excellent video!

Electrically the injectors on what range of voltage work?? How the high voltage gets build up? Thank you!

first view squad

I took the video of my dads truck making the ticking noise, it was only kind of making a ticking noise when i started it up but see if you can hear it. If you cant hear it i will wait for a time when it really is ticking and i will upload that. Just click on this channel and the video is there

Plus avast ingetor engine c13

You said you torque the rockers first then put in push rods.. I cannot get the injector push rods in after its torqued. Not enough room

Tools caterpillar

this video says no height tool needed. then your other video contradicts and says c10 and c12 need to use tool.