How to Install Connecting Rods on Lycoming O320 Crankshaft

Подписаться 2,5 тыс.

Просмотров 8 тыс.

50% 1

How to install connecting rods on a Lycoming O320 crankshaft. This connecting rods and crankshaft assembly will be installed in a Piper Supercub O320 B2B engine. In this video we show you how we install these connecting rods. This is the first step of the assembly procedure during an engine overhaul.
Thanks for tuning in. If you have any questions about the process to install connecting rods please ask them below and we'll do our best to answer them.
We appreciate it if you give this video a thumbs up and subscribe to our channel if you would like to see more content like this!
Check us out online and on instagram :
www.alaskaaircraftcylinders.com
/ akcylinders
We hope you enjoy our videos, thanks for watching!
We are a small aircraft engine overhaul and machine shop located in Wasilla, Alaska.
***This video is meant for entertainment purposes ONLY and should not be used as instruction on its own. You must be a certified mechanic to perform this operation and only by following the applicable manufacturers instructions for continued airworthiness.

Авто/Мото

Опубликовано:

2 ноя 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@user-pv4ph2pk8u Месяц назад

I wanted to see the details of the bearing Tang's on the rod and the cap to see if your installing them correctly! And bearing clearance with a bore gauge,and mic the crank and also side clearance!!!!

@dustybodine5221 3 года назад

Thanks for the great videos. Would be cool to see the entire engine assembly process from start to finish!

@akcylinders 3 года назад

Thank you! We will work on that! 👍🏻

@albertotamborrel 3 года назад

Thank you for these wonderful videos!

@davidwallace5738 3 года назад

Great job sir! Thank ya'll.

@maximolopezsr9399 2 года назад

Good instrutions

@John-nc4bl Год назад

Thanks for all of your excellent videos. There should not be any assembly grease on the parting surfaces of the con rod or the cap during assembly of the cap to the rod.

@fdfnfgnjfdjfjfk1436 Год назад

Thank u Sir

@deborahmcgee3711 5 месяцев назад

Have you done a video on big end bearing and main bearings?

@lilychavez8980 6 месяцев назад

🙏

@dudungdumyati2586 Год назад

Hello alaska, good

@derheeheehee6941 3 года назад

What bolts do you use to connect the crankshaft to the stand?

@redlinefury 2 года назад

What assembly grease do you use?

@billyoung6819 Год назад

I didn’t see you using any wrist pin retaining device before attaching head. Isn’t there any snap ring holding pin in piston?

@TangoBravo-SF Год назад

So does the 320 not call for stretching the rod bolt, just torque?

@dudungdumyati2586 Год назад

What is the price of a 320 engine one unit

@whatsmikedoing8761 3 года назад

You mentioned that if after installing the rod you spin it and it makes noise that you should take it off and clean everything up and reinstall. My question is, when you reinstall do you use new rod bolts and nuts? Or are the bolts only considered to be one time use if the engine has been run.

@jpooch00 2 года назад

The manual says that once they've been torqued or stretched to spec, they have to be replaced if they're removed - Period! No gray areas there. Taking the rods off and putting them back on would get pretty pricey REALLY fast!

@learndo7405 Год назад

When I rebuilt an O320 back in 2011 the bolts cost $35 each and the nuts $5 each.

@dudungdumyati2586 Год назад

Berapa harga mesinnya 0320 pak

@spurgear4 3 года назад

I have a question for you guys. I'm doing the top end of a o235 with 700 hours on it, what is the safest way to make sure I'm putting the correct rings in it. Chrome cylinder = steel rings and vice versa

@akcylinders 3 года назад

You are correct. Steel rings for chrome bore, chrome rings for steel bore. The best way is to go by part numbers. Their are individual piston ring part numbers and ring set part numbers for either chrome or steel bore. Can be found in Lycoming parts catalog or Lycoming Service Instruction 1037

@spurgear4 3 года назад

@@akcylinders Thank you . I know mixing them up is bad news