No video :(

How to Install Drip Edge Flashing | Shingle Roof Install Guide

Подписаться 10 тыс.

Просмотров 96 тыс.

50% 1

Drip edge is a crucial part of a properly installed roofing system. In this video, I will explain what drip edge flashing is, and then I will show you the entire drip edge installation process. Make sure to pay special attention to the aesthetic tips, as there is no point in knowing how to install drip edge if it doesn’t look good and you have lines showing at the front of the house. Quality is key.
0:00 Intro
0:08 Explanation - What Is Drip Edge?
1:15 Beginning the installation
1:41 How to install at the edges
2:40 overlapping two pieces
2:55 tip for joints and overlaps
3:31 Valley and Rake install
4:45 Underlayment
5:56 joints on a rake
This is one part of our latest series, “Shingle Roof Install Guide,” where we will walk you through every step of the process when installing a brand new shingle roof. From the drip edge to ice and water shield, from starter strip to flashing, we will give you all the details on how to install a shingle roof. So check out the rest of that series here: • Shingle Roof Install G...
We are a licensed and insured roofing contractor based in Burbank, CA, so keep that in mind when you watch our videos, as roofing regulations are different across the country.
We service the Los Angeles area, and if you’re looking for a trusted roofer, be sure to contact us today for a free estimate!
Contact Us!
► Website: bit.ly/3HYHoKL
► Facebook: / roofrepairspecialist
► Instagram: / roofrepairspecialist
► Read our Google ratings: bit.ly/34bQrVP
► Read our Yelp ratings: bit.ly/3mZChzP
Musicbed SyncID MB01DPKMFCT9MVJ

Опубликовано:

15 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 90

@RoofRepairSpecialist 2 года назад

Thanks for watching! Do you install drip edge differently? Let me know below 👇

@marisadiraimo Год назад

dont like the corner detail where the drip edge goes from plumb on eave to 5/12 slope on rake. the drip edge "pooches out" at the corner

@drewnicest4319 6 дней назад

Welp the previous commenter here addressed what I was about to say. That type of corner only works on flatter roofs. But also the nailing patterns you're teaching are not the best. To help prevent warping it's best to nail from the center out or from one side to the other. As an example, when you nail the middle, then the end, then fill in, you're putting an additional stress on the metal that can lead to warping. Might seem like a small detail but nailing from the middle out will give you the cleanest results

@EstateFlip 2 года назад

This video shows how to do it right!! You're on fire!! Very underrated channel. Keep it up!!

@RoofRepairSpecialist 2 года назад

I appreciate that!

@pcm7315 2 года назад

Nice tutorial - easy to follow.

@qstrian 10 месяцев назад

Aesthetics elevates this practice area from good to great 👍

@RoofRepairSpecialist 10 месяцев назад

Totally agree!

@larrybell5144 Год назад

All of your videos are exceptionally well explained and demonstrated. Very impressive!

@RoofRepairSpecialist Год назад

Thank you very much!

@PXanth 8 месяцев назад

if this fellow was to rate commercial roofers he would have to send 95% back to trade school... but on second thought the 'Trade Schools' of late have become Flake Schools. most cannot do proper work from the start and it often results in handyman type repairs that dont always hold out. some do some dont. Always a good watch and understand how to use your understanding of what happens and 'why we do things this way'. Mike Holmes could always use an expert opinion and you qualify to correct many if not most all complicated issues in hip valley gable mansford whatever combination and situation. wonderful workmanship and honest talk about 'whats happening in, on and under your roof' much appreciated. cheers

@RoofRepairSpecialist 8 месяцев назад

Thanks for your comment. I would say trade schools are non existent. I think it’s out job as roofer to train the new guys properly on the field. As well as platforms like this

@OnlineAutoRepairVideos 3 месяца назад

Your channel is GREAT information for us who are trying to do it ourselves. Hope nothing but the best for you and your channel!

@RoofRepairSpecialist 3 месяца назад

Truly appreciate it! Best of luck on your project.

@kevinandrews2717 2 года назад

Nice attention to detail. Good Work

@RoofRepairSpecialist 2 года назад

Thank you!

@brucekellett2269 7 месяцев назад

Very interesting video. The guys make it look easy. I also like the Southern Pacific Lines sign on the plate girder railroad bridge. Real neat.

@RoofRepairSpecialist 7 месяцев назад

Ya, that is a cool sign. I’ve always been a little tempted to take it… jk.

@user-ko5lk9do5l 2 года назад

well presented

@RoofRepairSpecialist 2 года назад

Thanks

@AntonioEnriquez-f5y 10 дней назад

In sections drip edge over lap is it fine to leave it as is or do I need to seal it?

@georgebrugh7822 Год назад

1-1/2 by 3 inch is preferred by most professionals. I fabricate mine to pitch, install vapor barrier 1inch past All edges, install starter flashing 1/2 inch down away from roof deck or facia board nail well, install starter shingles 1 knuckle past all edges.

@RoofRepairSpecialist Год назад

Nice, that sounds like some solid roofs your building.

@lilianadiaz5925 11 месяцев назад

Nice video., I’m learning thanks.

@RoofRepairSpecialist 11 месяцев назад

Glad to help

@DarylGibsonNJ 10 месяцев назад

Do you leave the drip edge at 90 degrees or bend it to match the pitch angle of the roof so its flush aganist both surfaces?

@RoofRepairSpecialist 10 месяцев назад

Bend it to match, if it is a steep slope you may need to get custom drip edge, if it’s low you can just push it in place

@jazzfan7491 8 месяцев назад

Well done!

@praful6890 Год назад

Nice video with clear precise instructions with no time wasted. BTW, would you recommend plastic drip edges ? If no, why not ?

@RoofRepairSpecialist Год назад

Definitely not. In general I dont like having plastic exposed to the elements, generally all plastic eventually dries up and cracks. Besides I dont see the advantage.

@stumpynubs5387 Год назад

Can the drip edge be against the framing or does there need to be space like the eves? on Rake edge?

@RoofRepairSpecialist Год назад

I like leaving a small gap between it1/8”

@stumpynubs5387 Год назад

Is this corner method for use with a gutter or no gutters?

@RoofRepairSpecialist Год назад

It doesn’t really make a difference

@johnsmith4630 2 года назад

good vid. i guess this is for hip style roofs where there is not gutters installed

@RoofRepairSpecialist 2 года назад

Gutters or not the concepts are the same

@victorgaos3 9 месяцев назад

What about if the roof it’s a single roof/lean to, how it’s the flashing installed? at the top of it.

@stumpynubs5387 Год назад

It appears like you are using gutter apron vs drip edge. Should gutter apron be used on rake edges and drip edge on ridge?

@RoofRepairSpecialist Год назад

Honestly not sure of the difference between the two. might be a regional thing because we dont use the term gutter apron here. The concept is the same I think, a 90 degree bent flashing with a kick a at the bottom.

@HBSuccess 10 месяцев назад

@@RoofRepairSpecialist What we call "drip edge" has a 1"-ish overhang built into it that extends beyond the edge of the roof, and it extends roughly 2" up the roof. The "down" portion over the fascia is also only about an inch, with the kick out like what you're using. What you're installing would be called "gutter apron" here (Northeast).

@olcotttheosophy 2 года назад

Andre Afsharian ! Well said .

@RoofRepairSpecialist 2 года назад

Thanks for watching

@andyponcia7722 11 месяцев назад

For the low slope.torch down besides the prep work on it does it install the same meaning the underlayment?

@RoofRepairSpecialist 11 месяцев назад

No different underlayment and different system

@robl496 7 месяцев назад

Hi there? Quick question .. How big is the gap supposed to be ? Between the drip edge and fascia 1/4” ?? 1/2” ??

@RoofRepairSpecialist 7 месяцев назад

1/8 will suffice, you want enough to create a slight separation of possible and be able to slide the gutter up under the drip edge

@robl496 7 месяцев назад

@@RoofRepairSpecialist appreciate you taking the time to reply to my question 💯

@AngelGarcia-gu1ck 9 месяцев назад

Se ve muy fácil, pero ya en el trabajo uno se cuatrapea, solo es cuestión de practica

@RoofRepairSpecialist 9 месяцев назад

💯

@notyomomma1 Год назад

Is it important to cover the top of the fascia board? I recently had the fascia replaced and the flashing in some spots doesn't cover the top of the fascia. I am afraid the wind will blow rain underneath and rot the wood. Thanks.

@RoofRepairSpecialist Год назад

100%, in a normal structure a 2" flashing will cover the fascia board. However sometimes we install bigger drip edges depending on the framing. Recently we had a custom 6" drip edge installed.

@propertyatlantic4859 Год назад

How do you do an inside corner when installing the drip edge? Do you bend it outward?

@RoofRepairSpecialist Год назад

I have a video specifically on that.

@stumpynubs5387 11 месяцев назад

Does the plywood overhang the facia board?

@RoofRepairSpecialist 11 месяцев назад

No, the plywood is and should be cut flush with the fascia

@biggoat1309 9 месяцев назад

Do you keep a slight gap running the drip edge down the rake also?

@RoofRepairSpecialist 9 месяцев назад

Yes, it doesn’t hurt

@canocano5480 Год назад

How does one make a outside corner with a gravel drip edge flashing

@RoofRepairSpecialist Год назад

Similar concept, if it is for a flat roof system which it probably is just make sure to seal that corner well.

@Jason.Davis. Месяц назад

I thought the nails needed to be centered over the rafters.

@RoofRepairSpecialist Месяц назад

If you don’t have fascia board that’s something you need to take into consideration

@tomcole4736 10 месяцев назад

you dont put the drip edge on top of the underlayment, ice and watewr shield

@RoofRepairSpecialist 10 месяцев назад

Since we’re in so cal I don’t use ice and water shield at the eave

@ronaldtoledo1727 2 года назад

👍👍👌👌

@RoofRepairSpecialist 2 года назад

Thank you

@fidellucas6632 Год назад

👍

@RoofRepairSpecialist Год назад

Thanks

@olcotttheosophy 2 года назад

☑️

@RoofRepairSpecialist 2 года назад

Best

@kurtn8759 Год назад

Technically this is a gutter apron… not a drip edge. 😊

@RoofRepairSpecialist Год назад

Are you sure. Google drip edge and that is what comes up.

@davidrandisi9562 2 года назад

That's actually c4 and a half rake edge not drip edge. Drip edge Is called F5. Sorry but that's not drip edge

@RoofRepairSpecialist 2 года назад

Not sure what C4, F5 and those terms are, honestly never heard of them. In LA we call them Drip Edge, so does everyone else in this area.

@k2_fx521 2 года назад

Even in Canada we call it Drip Edge metal, someone call it eaves and we use to call Gable for sides or ridge

@connorgordon2285 14 дней назад

I don't even have a roof

@RoofRepairSpecialist 14 дней назад

lol

@KenfurVinas Год назад

That is not a drip edge, A drip edge has a pointed edge

@RoofRepairSpecialist Год назад

If you mean a kick this does. The bottom of the drip edge has a 3/16 bend

@keithhoward4768 11 месяцев назад

That’s not a drip edge who’s is an F 5 or 8 That’s a rake edge a C 4

@RoofRepairSpecialist 11 месяцев назад

I think every region/ state calls it something different. In so cal if you call a supplier and ask for a rake edge or c4 they would have no clue what your talking about

@RoofRepairSpecialist 11 месяцев назад

I think every region/ state calls it something different. In so cal if you call a supplier and ask for a rake edge or c4 they would have no clue what your talking about