How To Install Long Tube Headers On An S550 Mustang (2015-2023) 

"While you can install long tube headers on jack stand, ain't nobody got time for that." I feel attacked as I'm watching this under my car on jack stands 😅😭

Headers are love / hate relationship with me. Love the power, sounds. Hate putting them on

Great video guys

Thank y’all so much for these videos! Just finished a set on jack stands and what a bear of a job. You’re right, AINT NOBODY GOT TIME FOR THAT!

Wow awesome results. I wish my Ecoboost could sound like that lol. 😂

Thanks for this video. Starting my kooks install this week. Im not on jack stands but not on a true lift either. But i do have a mid rise (40 inch) lift so i do have a lot more room than on jack stands but i can see its still going to suck, lol. But i ain't got time to pay over $1,000 for install. My hands will heal.

I got these done for my buddy within 2 days, definitely was a challenge on jack stands but also very do-able with a good selection of tools. One tip is be very careful when re installing the new bolts on the header flange as they can strip the block and you will need to run a thread chaser if they go in even slightly crooked

Just got some done on a 20 GT premium today in my front yard was a bit difficult but managed to do them in one sitting. They were Texas speed long tubes btw🙏🏽 Good video man! I just ran into a bit of a clearance issue when it came to taking the passenger side off and putting on. The ac line got in the way…..

I’m currently doing this on jack stands in my garage it’s definitely a journey lol listen to them when they say 3 outta 3 wrenches 🔧 it’s not impossible but it’s definitely not a walk in the park stay calm though and you can get it done ✔️

Can you guys explain how to turn off the check engine light with hp tuners from having no cats

Ac line can be tweaked a bit to open the path if doing while in car

Any advice on tightening the top motor mount nuts after the headers ??

I wonder why my top cat bolt is rusted so bad on.

How long did it take to install the headers?

What brand headers were these ?

I have borla attack cat back with xpipe and was wanting to get Texas speed long tubes do I just need the headers with the off-road connection pipes or something else?

One of the best videos for long tubes on a yote. I wanted to use my Kooks bolts that came with the set up, but most videos say to try to reuse some of the studs. Any thoughts on that one? Also, do I need to apply anything to the new gaskets that came with the headers? I see people and videos putting something on the gaskets but I don’t know what that is and they never mentioned it.

how did it crap out the driver side cat converter? Did it clog? how were you able to diagnosis it before it damaged engine?

If I already have cat delete midpipes what headers could I order to fit the aftermarket midpipes? They fit my factory headers.

What Headers did you use ? ARH???

I'm installing a se on a 2020 shelby cobra. It ain't no 6 hr job. I have a perfect shop floor. Cars 20" in the air. But the access to the bolts. Nightmare. The worst was that 1 high bolt on the converter. It took me 2 hours. With pb blaster and heat. 😂then, it just let loose. I'm having to remove almost every stud.

If i have a corsa xtreme will kooks headers hook up no problem? thanks.

I’m curious if I can use my borla mid pipe on long tube headers?

I’m glad mine cam with long tubes already on it. Lol

What happens to the catalytic converters? Ck engine?

I tried lifting engine using underhoist stand like you guys have in the video, braced in the same location and everything...studs and bolts are out of the motor mounts as shown in the video, but engine won't lift over the upper mount bolts (yes, those nuts were removed too). The motor mounts have a lot of tension still on them even though I have the engine a good 2-3" up over it's normal resting level...no way I can get them over the top engine mount bolts...please help!

Is it OK to use 2 inch headers with N/A 5.0 2018+ ?

Was that a mbrp street catback?

quick question, so if i buy long tube headers for my 2019 5.0 from corsa and i already have a 91/93 tune with roush CAI. so do i need a new tune for my car?

do i have to do all this to install some damn headers

What exactly do you mean when you say 'determine what studs can be reused'? do you mean some studs hit the pipes?

hey Landon any times from the track after you added the Roush SC? I have a 2019 GT A10 car and am in the research mode of the power adder. Really wondering how she runs at the track but my car is a weekend cruiser and don't want a track only car at all. Thanks in advance.

So I have a set of BBK long tube for 14 mustang 5.0, do I need any extension pipes to install them?

Just got done doing it in my drive way driver side no issues passenger side oh yeah right fit and bolts got a little tight in the Texas speed headers just make sure everything is started by hand and take your time and the top to front bolts can be easily done from the top I was just laying there tightening them. Also tip use a ratcheting crescent wrench makes life wayyyy easier

my 19 gt has 20k miles. should i just reuse stock gaskets

I have 1-7/8 bbk headers what mid pipe would I need?

I have a kooks 2 inch longtubes. The passenger side is slightly rubbing on the frame when I turn left. Has anyone had clearance issues with these 2inch headers. If so how did you fix it?

If I managed t -56 swap do yall think I could manage this ?

So i am taking ALOT of time doing mine cause im new to this and dont wanna mess up my car. I tried for the passengers side, keep the moutor mount on the driver side on and remove the passenger side motor mount. Remove all but the furthest front lower header bolt, and furthest back upper bolt. Raise the engine the 4 inches or whatever it is, and use a pry bar or somethign to push the motor away from the passenger side fender and toward the driver side, stock headers falls out. I did the same thing to install but i had my friend on the pry bar as i did that Keeping the driver mount on allows the engine to piviot from there when liftin, giving more clearance room on the passenger side. Also fuck that damn ac unit, little bastard is right in the way.

A swivel saved my life.. I didn't have to remove anything but the steering column screw

doing my kooks 1 7/8 headers rn. this video helps 😂🙏🏾

Could I do it. Yes. Do I want to do it. Probably not.

I take pride in not taking anything to the shop for installs. But god damn this is the one install I would have done it. ~19 hrs on the ground using jack stands. Nope.

@5:27 where was that wire attached?

do the rear o2 sensors need header extensions too?

One day, one day, I'll grow some balls and install long tube headers in my garage on Jack stands. Great vid everything looks so easy, but how ever long it takes on vid with installs it usually takes me double the time.

This guys make 10-12 hours job done in 14 minutes 😤

Does installing headers void your warranty?

Did it on jack stands

How many hours without the camera magic, aprox? How much do you charge a customer for this job?

How long did the process take? @LMR

I installed long tube headers on my 2019 Mustang GT now it wont start it acts like if its going to start and it shuts off can you help me out with I have installed the tune on it to?

Hopefully someone can answer this for me but I have a stock 2020 mustang GT, just got it with 3k miles on it. It’s now currently at like 9k miles and all i have done exhaust wise is had the resonator deleted and put an H pipe on it. So stock mufflers connected to the H pipe. The mufflers are active ones with the different modes and I love how it sounds now with the H pipe but I’m thinking about getting me some of these long tubes BUT the question for me is what all do I need? NOT TOOLS WISE but parts wise. If I order the long tubes itself right now do I need any other parts for a shop to be able to connect and put them on? Or can I have them just install the headers to the h pipe without purchasing any connectors, mid pipes, etc. ? Any comments are greatly appreciated! Just on a budget and don’t know for sure if I need any other parts which I would like to prepare for before ordering the headers because I like ordering everything all at once. Thanks!

Damn I wish I had the funds and equipment like a shop like this has to just be able to dump parts into my car lol

What wheels are those

666 max hp...haha nice!!

How do you know if the Cat goes out?

I can’t find the damn upper oxygen sensor

How much would a shop charge to install headers

How much do you charge for this exact job?

Anyone have problems with long tube headers on a 2019 gt ?

Did you have to cut the h pipe?

Local laws and regulations is hilarious because no mater where in the us you are not cats are a federal thing I still run em cause why not

Man now I wanna sell my SS for a 5.0 😂

Its an E8 inverted torque socket not E6

Can’t find these on your website

Hmm so pretty much so go with a procharger and be done with it lol. Too much work for little gains

Why do you guys have Likes/Dislikes disabled on all your videos?

Why tf am i even watching this? I dont even have a mustang😂

Hey it’s miiikee I may be able to get you some subs

Not fun when you can’t pass a smog check.

Any idea on how to tighten the top motor mount bolt? I can’t get to it from the top cuz the headers are in the way