How to install/remove valve guides

Подписаться 1,9 тыс.

Просмотров 14 тыс.

50% 1

How to install/remove Valve guides. The new valve guides are bronze.
Equipment used in the filming is Gopro Hero 8 from
Gopro.com
Othe equipment used for filming is the iSteady gimble from
hohem.com
If looking for the hot challenges go to
Music from Uppbeat (free for Creators!):
uppbeat.io/t/bosnow/street-kn...
License code: LJGODNB0O38QIPOS
DeathNuts.com

Авто/Мото

Опубликовано:

7 апр 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 18

@Honda_Drew Год назад

Great video!! I’m learning alot of stuff from your videos I loved your b trans rebuild video too!

@streetstancecivicgarage Год назад

Thanks for the feed back. I'm almost done with he bseries build stay tuned and I will be starting it soon.

@bauerleinjohn 4 месяца назад

They’re supposed to come out towards the camshaft side. The manual says to drive them to the combustion chamber side 2mm and then back up towards the camshaft side. I tried and it works just fine. Plus the tapered end in the combustion chamber side mushrooms but won’t score the inside because it’s quite a bit smaller than the bore. Good video otherwise

@john2ndname Год назад

Good technique with the old valve to support the guide and using grease to nurture the guide. did you measure the clearance between the boss head hole and the OD of the guide because if the guide is over sized to much than the boss hole ,the guide could get stuck half way and then you can run into all sorts of trouble.

@streetstancecivicgarage Год назад

Actually no I didn't. Didn't think about that. Supertech is pretty good with there parts. The only thing that needed done after was to ream them for the new valves.

@amritt1989 10 месяцев назад

you had me looking around for my phone :D

@wyattoutlaw2370 8 месяцев назад

How do you know when the valve guide is in far enough? Since you knocked the old ones right through , I take it there is no lip to seat it ?

@streetstancecivicgarage 8 месяцев назад

The new brass guide have a stop lip on them. They go in and out one way.

@CoreMaster111 Год назад

So it's fine to just push old ones out and new ones in? I see a lot of people say you have to heat the head up to certain temperature before you push old guides out and then later cool down new guides before you push them in or you can crack the heads or have the guides move once the engine gets hot etc.

@streetstancecivicgarage Год назад

I've heard that to buy I had no problem one old guide broke on me. But other that that had no problem. Just had to ream them .

@chrisschultz6129 3 месяца назад

It's same as installing bushings; you don't have to heat the outer part and freeze the inside part but it sure does help.

@michaeljuanis1684 Год назад

4.6l 4v c heads?

@mryang3644 4 месяца назад

Honda dohc vtec head

@zpwslayer9719 2 года назад

Damn pepper spray and tased? Shit lmao

@ericheisler5351 9 месяцев назад

Why didn’t you put the head in the oven or the new guides in dry ice? I am preparing to replace my first set of guides, and I’beating on the head with a hammer seems like a bad idea.

@streetstancecivicgarage 9 месяцев назад

It's fine it doesn't hurt the head you don't want to heat an aluminum head it may warp. Just use the tool that is made for it and you will be fine. Only thing is check the diameter of the new guides and mic the inside to make sure. The guide is not to big it can crack the head putting them back in. And use an air hammer putting them back in makes it way easier.

@ericheisler5351 9 месяцев назад

I’m gonna use my hydraulic press. Friend who I trust said that’s how he would do it at his repair shop.