How To Install Suspension Fork For Talaria Sting, Surron, Segway 

I have a set of these on the way and I'm feeling more confident in the swap-out process after watching your tutorial. Oh and you should look at doing voice over work or something in radio. You definitely have the voice for it.

Great video

Best headset discussion on RU-vid!

Great video, helped me thru this process well! Local bike shop swapped my bearing as well 🤙🏽

Great review and very comprehensive

Great tutorial!

Great video. I can't wait to see your review after riding it. I have been thinking about getting the tuned FastAce fork from charged cycle.

my kke forks triple clamp got bent and luna cycles told me to basically just buy new forks so i got some cheap amazon forks coming in soon, this video is super helpful, going to try this out and have the bike shop finish it off as a plan b

Excellent tutorial...will follow most of this for my Bomber 58 install this weekend:)

Interesting to see the evolution of the electric off road bike as it sucks up the best from the motocross and mountain bike worlds as I ride both ICE bikes EV road bikes and Mountain bikes. Interesting to see the motocross tyres and rims on to boost hubs, getting close that tyre to fork clearance but great result with 7th. EV bikes getting better all the time.

You can buy a bearing grease packer, a little Tupperware type of deal. Plus before putting the bearing on the lower pack it full of grease. I also recommend the Warp 9 Bar Risers with bars the Mtn Bike stuff is hooky.

after watching about half this video I knew I should probably just have a bike shop do it 😂 i've done my controller and just about everything else but my forks I don't feel confident doing and having them be dialed / done right

Thanks for the video. Helped a lot! At 10:25 you had all your pinch bolts and handlebars loose. You said that tightening it effectively acts like a press. I didn't see your fork tubes move up at all though. Should it? I didn't see mine go up either when I did that, so just curious if I need to go back and loosen the top clamp pinch bolts again and retighten the startnut bolt. Then retighten everything?

Yea talaria definitely doesn’t grease anywhere enough. Enough for mine to fail horribly. My friend looked at his and the same thing just not as bad. I’m 4100 miles on mine he’s 1500ish

Hello, how did you remove the bearing of La Fourche Dnm? Do you have a compatible bearing reference for this fork?

You didn't have to cut down the stem tube on the fastAce ?

I never saw anyone reuse a star nut.

I think it need more Greece

Did you get it for free, as many other RU-vidrs, or you purchased it?

Star nuts are cheap, reusing them is a stupid idea.🤔🧐🤔🧐

Radio voice

Подреж ножом резину

The Fastace and new Talaria factory forks both come almost ready, which is nice because you don't have to cut them. The main challenge is removing the lower bearing from your old fork because there's a tiny plastic ring under it which probably also has to go on the new fork. You just need a bearing remover, a star nut and star nut presser to do it yourself, then find something like a PVC pipe to push the bearing onto the new fork. Some people buy the regular Surron headset kit from LunaCycle to get a star nut, new bearings, and extra hardware. I used the star nut that came with my new Talaria factory fork, but it didn’t come with the Fastace fork (no big deal) unless it’s otherwise specified or included (in case you need it) and they're the same size. Luna included it for me in the headset kit. Other than that... The little plastic bracket I had from my DNM fork (the one that holds the brake hose) doesn’t fit Talaria or fastace forks. Ebikezilla might have it for the Fastace/Talaria factory fork, and it. You could also use a zip tie instead.

so yea only thing I wanted to see was taking off the bearing yet you didnt make it 😒😒

Is this fork narrower than the DNM ? My DNM is 4.25 in between the stanchions. Waiting for my Fastace fork... thanks for the informative video 🤙🏽