No video :(

How to Jack Up/ Lift the Nissan 350Z / Infiniti G35 when working on it from Home | AnthonyJ350

Подписаться 118 тыс.

Просмотров 107 тыс.

50% 1

In this video we should you the preferred lifting point on the 350Z when working on it from home or your shop. These methods will only work if you have a hydraulic floor jack and proper jack stands.
When using a scissor jack the pinch seem must be used.
#FloorJack #JackStands #RaisingaVehicle #Nissan #350Z
Subscribe for more automative tips!: bit.ly/sub2anth...
Watch my most popular uploads!: bit.ly/anthonyJ...
Website: gofasthavefun.ca
Instagram: / anthonyj350
Twitter: / anthonyj350
Facebook: / aj350
Shop: www.amazon.com...
Music available - www.jinglepunks... & www.epidemicsou...
About AnthonyJ350
I am a Mobile Electronics Certified Professional 12 Volt Installer (MECP Certified), Business Management Graduate (KPU), with a Professional Driver's License and a genuine automotive enthusiast who loves working on vehicles and I want to share my experiences with you. The goal is to help other people who can hopefully learn from my unique outlook towards vehicles, experiences and working practices.
Please feel free to ask questions or give feedback either in the comments or e-mail me.
New videos every week.
Please check out official web site (www.gofasthavef...) for our disclaimer as we are not professional mechanics but experienced automotive enthusiasts sharing our experiences and providing entertainment content.
Go Fast Have Fun provides the content in this video, for information and entertainment purposes only.
The information in this Video presents guidelines to help vehicle enthusiasts modify or repair their vehicles and to demonstrate what car culture is all about. Go Fast Have Fun make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the Video or the information, products, services, or related graphics contained on the Video for any purpose. Any reliance you place on such information is therefore strictly at your own risk. Nothing presented should be relied upon you for your modification or repair plans for your vehicle and is not in any way professional mechanical advice.
Go Fast Have Fun strongly recommends you consult with a professional automobile mechanic to ensure that any modification or repair plans for your vehicle are appropriate for your vehicle.
In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of, or in connection with, the use of this Video and the information presented within it.
Go Fast have Fun
Canada
How to Jack Up/ Lift the Nissan 350Z / Infiniti G35 when working on it from Home | AnthonyJ350
• How to Jack Up/ Lift t...
ANTHONYJ350
/ anthonyj350

Опубликовано:

22 июл 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 117

@lnvfx 7 лет назад

Hey Anthony: long time viewer, first time commenter. This video made me subscribe to your channel! Love the tips and content on the 350z.

@AnthonyJ350 7 лет назад

Thanks for watching and I'm glad you like the tips. But what took so long to subscribe?

@jp8950 6 лет назад

Trying to do as much maintenance on my own as possible- thanks for this video, super helpful.

@AnthonyJ350 6 лет назад

J P Glad it helped!

@RjayvidaPLUS 5 месяцев назад

Number one video on lifting the 370! 🔥🔥🔥

@AnthonyJ350 5 месяцев назад

Thank you for watching!

@victorpla16 7 лет назад

I can Jack myself

@AnthonyJ350 7 лет назад

Well that's good to know.

@no_handle_required 4 года назад

You're what's wrong with the internet, your parents failed.

@wiretrap1035 3 года назад

One word---GODSEND. THANK YOU.

@AnthonyJ350 3 года назад

Glad the video helped!

@CarAudioInc 7 лет назад

I got thrown off when you said Z instead of Zed. And I'm from the U.S. I'm a disgrace to my country. LOL

@AnthonyJ350 7 лет назад

Ya I've been mixing up my pronunciation last few videos. That way I piss off all the regions equally ;)

@TC-td1vx 4 года назад

Zed is correct way to pronounce for us candians. Lol

@averageyoutuber113 3 года назад

@@TC-td1vx weirdly I still like saying "350zee" lol rolls off the tongue better. Same with "ZeeL1" for ZL1 Camaro. Prob just used to hearing Americans saying it that way in media tbh lol.

@vladmirputin1711 6 лет назад

Very thorough video, thanks for the tips!

@AnthonyJ350 4 года назад

Thanks for watching!

@FraudVoze 4 месяца назад

oh word , you think my 350z can move , hilarious 😭😂😂

@AnthonyJ350 4 месяца назад

Thanks for watching.

@FraudVoze 4 месяца назад

@@AnthonyJ350 absolutely finally got my battery back in and i appreciate the help and support , she’s going on jackstands this week after the crash on Christmas !! You are one of the main reasons this car is getting back up and going

@AnthonyJ350 4 месяца назад

@@FraudVoze That's so awesome to hear the video are helping you!

@julthebaber 7 лет назад

OMG i needed this vid lmao. Always had problem jacking it up!

@AnthonyJ350 7 лет назад

joul the babou How were you lifting it before?

@julthebaber 7 лет назад

One corner at the time and i placed the jackstands at the pinch welds which destroyed it :( I'm gonna use hockey pucks on my jack see how that works

@AnthonyJ350 7 лет назад

You need these ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-lzN9LluqgrY.html

@JohnHighmerSmith 4 года назад

@@AnthonyJ350 I do wish you guys were using the more wide and having holes/pins jack stands I don't like those skinny claws or that ratcheting system of locking in they always scare me your cushion things are nice though, and I'd rather see you do it the way you do in this vid and not like motordyne with that sideways thing, also scary to me to be only holding the rig up on one side of that frame rail good work sir!

@AnthonyJ350 4 года назад

@@JohnHighmerSmith Thanks for watching! I totally agree that we are in need of a jack stand upgrade. I'm going to get the ones specifically for the pinch seam. I totally know what you mean about the Motordyne guy, he came after me (several videos...) saying the way we prop of vehicles is completely wrong and the side ways jack stand is the best way.... I hope no one gets injured from doing it that way. The good news is, I'll be debuting the beginning of our custom house build which will have a 1200 sq ft shop and a 4 point hoist to do videos! Much safer to take on projects.

@maktodd5440 5 лет назад

This makes my oil service so much easier to do

@AnthonyJ350 4 года назад

Glad it helped!

@ketobeast8489 10 месяцев назад

Get Rhino ramps, reverse in your driveway then pull forward onto your ramps. Oil change in 15 minutes

@thegame123ize 5 лет назад

Hey bro I'm having trouble with low ground clearence. I'm running 235/45R17 in front and 225/50R17 rear ( they came stock maybe) what would u recommend? I want highest possible ground clearence( i know i'll get lower performance/ power) without damaging/replacing anything. Thankyou

@AnthonyJ350 5 лет назад

This is the setup I run with stock height suspension. It has a very small wheel gap and I can go on the ferry (ramp is very aggressive) and don't have to think. On my old exhaust setup it still put down 279 wheel horsepower. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-x9XLGAojw6w.html

@iandalonso 7 лет назад

I just use some cheap pinch weld adapters that I got from amazon. Totally didn't know about that front center jack point lol.

@AnthonyJ350 7 лет назад

Ian Alonso Do they work well? Can you send me the link because there are times I have to use the pinch seam.

@iandalonso 7 лет назад

I can't find the exact one that I bought, but if you search for pinch weld jack adapters on amazon they're pretty much all just a hockey puck with a groove in it. I have some that are made of polyurethane, but the rubber ones seem ok too. I normally use the adapter just to raise the car up and then place my jack stand underneath. The adapters that I got were also a little bit too short to fully envelop the pinch seam, but the weight of the car on the adapter mold it enough so that it fits. The polyurethane seems malleable enough to bend under stress, but not break.

@AnthonyJ350 7 лет назад

Ohhhh I know what you're talking about. I'm still trying to find something to go on the pinch seam and use a jack stand with it. I would use the pinch seam more if I could do that because that's what it's designed for. Try using the jack point at the front of the car and let me know how it goes. I recheck several times when I lift from there to make sure I'm not on something else.

@JohnHighmerSmith 4 года назад

@@AnthonyJ350 I cut some wood, works really well but I have jack stands with full flat top (little bends up in the end but I can fit a 2x4 in it no prob) and cut a little divot for the rail and boom, it's good be careful where you set it though because the rocker panel bit that hangs over the underside to hold on ends right around the pinch weld jack/stand point so if you put the wood/puck/amazon adapter/supersweet Kent More SPX SST No. LM4519-0000 (seriously if you find that lemme know that would be so cool to have) then you just be careful bc I think we could smush the sideskirt rocker panel bit too much

@MotordyneG35 7 лет назад

Looks like I need to make a new video. I have the Nismo diff cover and you are supposed to jack it up from the fins, they will not break. Interesting, I never put my jack stands on the unibody frame, I always put mine under the rocker panels and you have the stands turned the wrong way. When you turn them that way, yes you do need the rubber covers.

@AnthonyJ350 7 лет назад

Motordyne G35 Ya I like them side ways there because it cups the frame rails. I just feel it is less likely to dent those rails that way.

@MotordyneG35 7 лет назад

I should say, still a great video. Just a couple things I do differently.

@MotordyneG35 7 лет назад

My first car was a 240sx, an s13. I had that before the G35. The 240sx was used when I bought it. Where am I going with this? The person who had it before me would jack the car up on the unibody part, same area you are, but he was lifting the car 1 side at a time. Unlike you who are doing it in the middle upfront and the back, which is better, I agree. I always jack up from the rocker panels and here is why. The 240sx was in Ohio, so it saw snow and salt. From the previous owner, they had smashed in the area of the unidbody by lifting it there with no rubber pad. Rust started. Then it got so bad, it was coming up through the floor. I had to have my whole unibody cut out and re-welded. Plus it is harder to get the the unibody part of the car anyway than the rocker panels. I"m looking at the service manual now. I do not think you are supposed to jack on the unibody part and I'm correct. It shows the rocker panels as jack points, the diff and in the center in the front. You are not supposed to jack up on the unibody frame. Maybe holding it with jackstands is ok, but I have never done it. 12 years of jacking up my G too, I've never touched the unibody frame with jackstands or a jack. I did my clutch on my back too.

@AnthonyJ350 7 лет назад

I want to use the pinch seem but I'm still trying to find the jack adapters the manual suggests to use. My current jack stands stick out too much on the sides and will be in the floor before it touches the pinch seem. I've also see crazy jack stands on Jay Leno's garage that I would totally use. www.pinterest.com/pin/619033911252017638/

@MotordyneG35 7 лет назад

Again, like I said you have the jack stands turned the wrong direction. All you need is a rubber pad on the jack, to jack up on the pinch seam. You do not need rubber pads on the jack stands, if you use them the correct way. I made a proper video on how to jack up your car correctly, if you want to see. I referenced you in the video.

@scottspooner6070 5 лет назад

Nice wheels...

@AnthonyJ350 5 лет назад

Thanks

@AbdullahZ33 7 лет назад

Nice vid I have 3 tons jack for low rider that's wat I use for my z33, Try make a video how to install headers on z33 thx. Your the best

@AnthonyJ350 7 лет назад

Abdullah Alrashid I don't even know if I want to attempt it. It looks like a pain, I'd rather pay someone lol.

@AbdullahZ33 7 лет назад

AnthonyJ350 thx for your advice

@hakimrahman85 Год назад

What's the best way to lift all four sides on jack stands? Any particular steps to follow or which sides to begin with ?

@AnthonyJ350 Год назад

I lift the front up, then the rear. Perform on level ground.

@hakimrahman85 Год назад

@@AnthonyJ350 cheers

@HOANGJJNGUYEN 5 лет назад

hey man! Could I use a scissor jack and a jack stand to replace the break one side at a time? I dont have a floor jack tho.

@AnthonyJ350 5 лет назад

As long as you use a jack stand to support the weight of the vehicle. I highly recommend investing in a floor jack though.

@101TheKMan 7 лет назад

Out of curiosity what rear diff bushing are you running? How's the NVH? I'm looking at replacing mine and undertaking some stage 1 mods as per your recommendations

@AnthonyJ350 7 лет назад

I run Energy Suspension's polyuerthane bushing. Didn't notice anymore harshness, but the vehicle just felt better when applying power and during hard shifts. The transmission mount you'll notice more vibration until it breaks in.

@quincygaming9529 2 года назад

Would you recommend jacking and working on one end at a time or getting the car jacked all the way up? A little nervous about the jack slipping off the diff. Need to change my shocks all around and haven't jacked a car before. A little nervous about hurting my car or myself

@AnthonyJ350 2 года назад

You can do the front end, then the back end separately. Make sure the ground is level and secure the wheels. When the back end is up nothing is preventing the front wheel from rolling but your blocks. Also put a wheel under the car for extra cribbing. I would have some experienced with you to help you out and supervise.

@wayneduford64 Год назад

Hey Anthony, I noticed you replaced your diff bushing. Did you do this yourself? Mine just went and need to do it...

@AnthonyJ350 Год назад

At the time I had The Z Shop install it for me. I would attempt it now myself seeing Z1 has a removal tool they developed for it.

@AnthonyJ350 Год назад

I recommend Energy Suspension bushings for a street driven car.

@wayneduford64 Год назад

@@AnthonyJ350 Thank you!

@AnthonyJ350 Год назад

@@wayneduford64 You're welcome

@huntermyers6409 6 лет назад

Hey man i recently jacked up my 350z on the pinch weld and it bent a little bit and im kind of freaking out about it will it effect the performance of the car or will it be all cosmetic i am planning to build the motor in the car so i am worried in the future the bend might effect performance. If you could help me out or have any info on this i would greatly appreciate it thank you

@AnthonyJ350 6 лет назад

Hunter Myers No it won't affect anything as far as handling. If you lift from the pinch seam make sure to put a pad on the jack or a piece of wood, just make sure the wood grain is going against the seam so you don't split the wood.

@huntermyers6409 6 лет назад

AnthonyJ350 ok awesome thanks for the help man i really appreciate it.

@huntermyers6409 6 лет назад

AnthonyJ350 one more thing im not sure if the it was lifted on the pinch weld seem the bend is near the rear end of the car not the front not sure if that makes a difference

@AnthonyJ350 6 лет назад

Hunter Myers I don't think so. Of you're really worried you can always have a body shop inspect it.

@alessandroplascencia4368 3 года назад

Bro could you send me the link to the axlestsnd poly pads?

@AnthonyJ350 3 года назад

You can get them here rover.ebay.com/rover/1/711-53200-19255-0/1?mpre=https%3A%2F%2Fwww.ebay.com%2Fitm%2FProthane-19-1412-Urethane-Jack-Stand-Pad%2F333875226141%3Fepid%3D3017022999%26_trkparms%3Dispr%253D1%26hash%3Ditem4dbc83a61d%3Ag%3ADp8AAOSwKflgF55x%26amdata%3Denc%253AAQAFAAACgBaobrjLl8XobRIiIML1V4Imu%25252Fn%25252BzU5L90Z278x5ickkCrLl8erj3ATP5raQxjc%25252F%25252BwnOaxg3cNUblvWHezM6ZajPA%25252BI%25252F%25252FLV%25252BdlNfdhgfx%25252FA%25252B%25252B7jwEkg3SGJCeVilC9VB53MAdhzgC6lHiW6%25252FIacm6vUKZ3g%25252FuSasN8GRIZfMXXJao4%25252Bte1g6FqfgVweArld7qV%25252FuuSPXQNpbXSv1XEvvfEFzWT8jq4cDpvZ9UIcfxCxNGFTElYH9szycLpR4kKUNH4eDUvUoQ353U62sNYYtcqvYRCBl%25252FjHGswCaqQ%25252BDg6mgqjWsypbuFPcTU3pjQBMaz8ksxrMpKtjSA2aDazLg%25252BdpBoprMGW8Oj62HCE0el3I662lo2g9VzufSNPU2aN9MAq0AdZE1l2kMYfq2OsV6dRyvxAbqf%25252FYFjds4iXzhdsSSLhyY2i%25252FmHbuMUuT%25252BUia4RGB3hrtq7FgcwAj5lXAUOTp%25252BEzKhI8ofsSq0rKAWjfsfNROKhSa2G4fBoP7Bq%25252FvLAnhPZIaXHnLkM6leBZsmQ3n3UTIw1EKGCF%25252FcdL7dH%25252BJSsGDW9UXHBnWByzp%25252F%25252Bqdh4jDyS5BenMJrcpsu77jCX91gUjJgsvVvyX8a1mKXJKIB2rQ1h6SxlrXv4RZC8xWhFX7MB2hmyZ9DW9a25UZWwVv%25252FXWqh054Oip9EKUHSB4X4qWzIfG3K1KyDBwR%25252FjQAYHrqXToa6dhn58dYlOogtHwlOdKvhPQNVpmUsUvcgSMYnlmup3vAxnRlj7Cctp1dcKCMRLHdtunH9uetnA3gcG0qIUe84ecf3A78158qXe8NgjoKaU08h%25252FxhEYZKjnu%25252BCbHxHNNTTGsxdH7gt%25252B5ky4AM%25253D%257Ccksum%253A333875226141fb8b256bce984121b14b7e12f3b594e4%257Campid%253APL_CLK%257Cclp%253A2334524&campid=5337982243&toolid=10001&customid=

@justoutdoors2441 4 года назад

Hey man my pinch point at the rear of my g is rotted any other place I can my stands?

@AnthonyJ350 4 года назад

There the W brace under the car and also the trailer arms at the area the bolt goes through that's attached to the chassis.

@justoutdoors2441 4 года назад

@@AnthonyJ350 thank you

@ulyslightt 3 года назад

Do you know if the same rules apply to an 06 g35 coupe??

@AnthonyJ350 3 года назад

It should, they're practically identical chassis wise

@ulyslightt 3 года назад

Thanks

@donaidtrump2664 7 лет назад

What size are the spacers that u run on your car?

@AnthonyJ350 7 лет назад

No spacers on this car, just the proper offset. Watch this video and you'll see my specs. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-x9XLGAojw6w.html

@fernandohood5542 4 года назад

What about using the standard jacK?

@AnthonyJ350 4 года назад

You could but it's slower and more difficult. You'll still want to supplement it with jack stands to be safe.

@samson_BNR32 7 лет назад

could use hockeupucks with the axel stand yeah?

@AnthonyJ350 7 лет назад

ssmoly I don't know. It looks unstable to me. I have never tried it that way though

@pattrottier7636 4 года назад

I use pucks, I did cut a small channel in them for the pinch seam to sit in... I also use a third on the Jack, probably not necessary, but a bit softer on the car. Especially on the front Jack point, it sits slightly shy of the bracing and the bracing tends to sit on the edges of the Jack platform without the puck

@HardhitterHardhitter 4 года назад

What front lip do you have

@AnthonyJ350 4 года назад

MagicDrift, here's the video on it ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-cJe5ibTavBA.html

@vnny2081 2 года назад

tried to lift it from the center. fell on my oil pan -$300 😬

@AnthonyJ350 2 года назад

Did you do it on level ground?

@AnthonyJ350 2 года назад

Fell on your oil pan? Or you lifted from your oil pan? 🤔

@vnny2081 2 года назад

@@AnthonyJ350 it fell on the oil pan.. it was in ground level in my garage. But i used an old jack and paid the price for it

@AnthonyJ350 2 года назад

@@vnny2081 Good thing no one got hurt, so it was a valuable lesson. Time to go invest in a good jack and Jack stands.

@davabran 7 лет назад

NICE!

@AnthonyJ350 4 года назад

Thanks for watching!

@dumbtweacz2150 4 года назад

Same as 370Z????

@AnthonyJ350 4 года назад

That I'm not sure

@kennyrzr3953 5 лет назад

thanks man

@AnthonyJ350 4 года назад

Thanks for watching!

@jnagime 5 лет назад

I almost damage my gas tank......got a little dent.....

@AnthonyJ350 5 лет назад

You have to use the pinch seam on the rear to support the vehicle if you intend to lift the vehicle and work on the rear suspension.

@yaboibullworm289 4 года назад

Let

@AnthonyJ350 4 года назад

Thanks for watching!

@gagebrown3691 4 года назад

You literally didn’t show where to put it on the front. You used mechanic lingo throughout the whole video without explaining shit about shit except for why you use polyurethane pads.

@AnthonyJ350 4 года назад

I don't think you watched the whole video... 3:08

@AnthonyJ350 4 года назад

You'll get by further in life if you just ask nicely. If it sounds like you're whining when you type, you probably whine when you talk without realizing it.

@AnthonyJ350 4 года назад

Sorry I meant 3:01

@Mike253boom 4 года назад

Yeah, put a jack stand on a unibody. Smart guy, not hahaha

@AnthonyJ350 4 года назад

Hahaha, do you see any damage to the subframe after? I have a video for comments like this ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-CIV21MmcVWs.html

@jacksiscavage6265 6 лет назад

Umm, Jack it up then put ramps under the tires. Lol, Jack stands? Who needs fricken Jack stands! Get smarter peeps.

@AnthonyJ350 6 лет назад

How do you service the brakes or any suspension components if you use ramps all the time? Unless you're just doing oil changes, the wheels have to come off to work on the car.

@jacksiscavage6265 6 лет назад

@@AnthonyJ350 You are right... pretty tough to work on brakes if you are on ramps. I was focused on my front of motor issue. Working the tensioner pulleys from underneath, the ramps are a good option. .. my bad

@AnthonyJ350 6 лет назад

@@jacksiscavage6265 I agree ramps are easier to deal with and are probably safer. Just depends when you're working on.

@JohnHighmerSmith 4 года назад

also you have to lift pretty high to get ramps all the way under unless tiny ramps...my ramps put the wheels up like 10" off the ground, and that's in the little dip, tires probably would have to clear a full foot to get the current ramps I have underneath