How To | Kia Sorento | Drive CV Axle Shaft Replacement |

Подписаться 7 тыс.

Просмотров 46 тыс.

50% 1

Vehicle In This Video: 2011-2016 Kia Sorento
If you have Kia and you need to replace front cv axle shaft or you want to know how to remove front cv axle shaft we will explain that in this video. It is not very complicated to replace front cv axle shaft on Kia in most cases. We demonstrated how to replace cv axle shaft on 2014 Kia Sorento but the video may be helpful on all other Kia Vehicles.
Support Us On PATREON: bit.ly/3qQsO07
Support Us On PAYPAL: bit.ly/3r4DPdJ...
--------------------------------------TOOLS I OWN--------------------------------------
30 Degree Push Pin Removal Pliers: amzn.to/3BlCx1K
Wheel Stud Installer amzn.to/2TQkstm
Stretch Belt Tool amzn.to/3e8bYVk
Gear Wrench 1/2 Socket Set amzn.to/3e6XDIv
Disposable Gloves amzn.to/3e3Bc6Y
Toyota/Lexus Oil Filter Tool amzn.to/3k6wuti
Vacuum Brake Fluid Bleeder amzn.to/3xzATZB
Gearwrench Ratcheting amzn.to/2Vm2kHU
7-Piece Spare Tire Retrieval Tool Kit amzn.to/2VlKWmE
Oil Filter Wrench Wrench Kit amzn.to/3ARUjLi
Oil Filter Pliers amzn.to/3yENJpo
Craftsman 1/2 Impact Sockets Set amzn.to/3e5z92e
Screw Driver Set amzn.to/3hYt5K5
Hand Impact Driver Set amzn.to/3yFdF48
Dual Piston Brake Caliper Push Tool amzn.to/3yJDe47
Wind Back Brake Caliper Tool Set amzn.to/3yKGlsJ
--------------------------------------------------------------------------------------------------------
If this video helped, let us know in the comments, and if you liked this tutorial, leave a like and subscribe fore more content like this! Thanks for watching!
Repair Tips & Secrets Only Mechanics Know
DISCLAIMER: This video description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission.
#howto #diy #automotivedysfunction

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 64

@syrahminush Год назад

Thank you for the socket sizes, my husband is going to replace mine since it's spewing grease everywhere. i have a 2014 kia sorento limited sxl and this is a huge help for us!

@AeoniumKing 2 года назад

I appreciate you for adding the socket sizes, saved me a few trips to the toolbox.

@keithwright2726 2 года назад

I need an impact. I just did this for my mother in law. Took me 3 hours. You make it look so easy lol

@KuriVaiM Год назад

O really? iam facing same problem on my 1st gen sorento and some random shop told me that this axle shaft replacement will take a whole day, i could not believe it then ...

@BugzKiller 5 месяцев назад

Well it was easier he has a car lift versus laying on the ground like I did all my life. Cuts the time in half when you have a car lift

@bigbadbillybrad Месяц назад

If I did this job in 3 hours I’d probably want a trophy

@mikemannion788 2 года назад

A+ on capturing the work detail on your video and also including the socket sizes. Thank you.

@alexiskl47padillaestrella21 2 года назад

Buen video 👍 me encanta como explica da todas las instrucciones bien 👍

@jameshaggard2102 2 месяца назад

Good video. I didn't see where you disconnected the tie rod.

@ivanmaldonado6693 Год назад

Thanks for the tips!!!!

@syedrehmanshah9479 6 месяцев назад

Tanks for help with my sorento

@mistermandrews Год назад

Any idea what size cotter pins you used for the axle nut and the tie rod castle nut?

@jeffblahblah5226 4 месяца назад

clear vid nice one!

@kiosoyoufer 2 года назад

every few miles it is recommended to change the bearings ,mine make noise and one boot is leaking grease passenger side 2011 sorento LS

@AutomotiveDysfunction 2 года назад

yea change bearing either when it has play in it or its making noise one of those two

@jamesrichardson771 11 месяцев назад

Very Nice💥 🛠

@emagowan 10 месяцев назад

Great video as long as you turn the volume down so you don't have to hear the crap "music"

@tjvaldez4787 2 года назад

Is this a good time to replace that carrier bearing too? Is there much more involved?

@AutomotiveDysfunction 2 года назад

No need .. I ve never replaced one so far .. (but then again I live in rust free state) I wouldn’t touch it if it’s good

@brittneyturnbow771 2 года назад

is that the bar that goes to the transmission?

@AutomotiveDysfunction 2 года назад

@@brittneyturnbow771 yes

@brittneyturnbow771 2 года назад

@@AutomotiveDysfunction is it hard to change that? There are metal shavings and stuff around it where it goes into the trans

@AutomotiveDysfunction 2 года назад

@@brittneyturnbow771 it shouldn’t be that I think there only 2 or 3 bolts holding that shaft and after you take those bolts out it should just come out same as this axle did

@HewHolden 2 года назад

Is there anything holding the cv axle to the hub other than the nut? I’m trying to do mine but I can’t get the shaft to budge I’m thinking it’s just seized really bad

@AutomotiveDysfunction 2 года назад

Just that one nut … spray some penetrating lube and smash the shit out of it … who cares if cv shaft mushrooms because you are replacing it anyway don’t be afraid to hit it hard

@michaelrobertshaw4790 2 года назад

I’ve tried what the video showed, a puller that you hammer on, the puller with an air hammer attachment, beat the devil out of it…. Cannot get it to budge. I could try some PB blaster or something next

@AutomotiveDysfunction 2 года назад

@@michaelrobertshaw4790 where in my video (time?)

@jak77942 2 года назад

@@AutomotiveDysfunction is there any special alignment/position that has to be done when installing a new one or can the axle go in just about however you can get it in?

@AutomotiveDysfunction 2 года назад

@@jak77942 there should be like C clip that makes kind a go hard in but with little wiggle left, right , up and down at same time when you are pushing in , it should just slide in ..

@maddazhell3519 Год назад

your video doesn't show removal of the ball joint. Does that probably need a pickle fork to separate?

@AutomotiveDysfunction Год назад

I didn’t remove ball joint for cv replacement as you can see in video I removed 2 top bolt that holds strut assembly

@juangomez-to5nx Год назад

Hi, i help please! I already removed the right side like you, vey easy but the left side (diver side) it was impossible remove the axle.

@AutomotiveDysfunction Год назад

What’s wrong

@juangomez-to5nx Год назад

@@AutomotiveDysfunction axle shaft, the end cap is stuck and i broke an inside seal now trying

@notsofast5495 2 года назад

I have a Santa Fe with clunk in front that Hyundai has a TSB on regarding a washer between back of hub and axleshaft. Yours is the only video I've found that shows that washer. You didn't change it. It appeared to have been stuck to back of hub then came loose when you put new shaft into back of hub. Do you know if this washer is the same for the Sorento and Santa Fe? I can't find the washer at any dealerships in my area. Local tranny shop says my transfer case is bad but I sure would like to try this first. I have no washers in place now.

@AutomotiveDysfunction 2 года назад

what year/model/engine size/FWD or AWD?maybe I can help to look up that part for you

@notsofast5495 2 года назад

@@AutomotiveDysfunction 2008 Santa Fe, Lkmited AWD. I think the washer is Hyundai 51755-2B020-FFF. Can’t find them locally and I would like to try installing one to see if helps my clunk before the shop wants to take out the T-case. I think because the axle nut tightens the shaft to the hub thst the freeolay is actually in the joints themselves and the washer helps to compress the joints as it gets tighened up. I don’t see freeplay between my hub and axle. Thanks for your help

@AutomotiveDysfunction 2 года назад

@@notsofast5495 does it make clung noise only on right turn? if it does more likely they re right

@notsofast5495 2 года назад

@@AutomotiveDysfunction only when shifting from park into gear. I pulled driveshaft from transfer case, put it back in neutral and raised front wheels. There is a lot of freeplay in t-case ss opposed to the used one I picked up today with 58,000 miles. However, the rear diff seems to have same freeplay as my tcase.

@beardedcamelnuts 6 месяцев назад

@@notsofast5495what did you end up finding about the washer? I'm about to do this job and other videos say no washer, and saw reference to it in another post.

@rocket3431 2 года назад

so after replacing ball joints and wheel bearing i get a clack when accelerating or on gear changes from the driver side. would it be this?

@AutomotiveDysfunction 2 года назад

I would check and make sure you got all bolts/nuts tightened..sometimes you hand screw the bolt and get distracted & forget use wrench

@rocket3431 2 года назад

@@AutomotiveDysfunction thanks ill check that

@BugzKiller 4 месяца назад

Can anybody Please tell me if you get a New Spring Clip when you buy a new axle? Thats the end that he used a pry bar on, transmission end. Or can you use the Old spring clip when installing a new axle??

@AutomotiveDysfunction 4 месяца назад

where in video .. time?

@geepeezee5030 2 года назад

Alignment performed too?

@AutomotiveDysfunction 2 года назад

yes,its always good to check it

@irisbaez1972 6 месяцев назад

NOOOOOOO. if you don't remove the tie rod, you don't need alignment. SAVE MONEY IN STUPIDITIES.

@raynocki 2 года назад

Is this only a dealership item ?? I have a 2019

@AutomotiveDysfunction 2 года назад

No it’s not .. it might be a day out or so but you should be able to get it in local auto part stores

@raynocki 2 года назад

@@AutomotiveDysfunction auto part stores don’t have any only for driver side

@kylepopell3585 Год назад

That wheelbearings post to be hand torqued

@hank2.073 2 года назад

What size is tje barrel nut looking one?

@AutomotiveDysfunction 2 года назад

axle shaft nut? show me time in video.. all tools included in video

@Quantumvp 2 года назад

I just changed my passenger cv axle just like this one and mine is still loose at the transmission end

@AutomotiveDysfunction 2 года назад

Trying replacing other end .. and if still loose might be internal of transmission (just a guess)

@BugzKiller 5 месяцев назад

Anybody know of this will work for a 2007 Kia Sorento And isn't there a seal That Goes on the transmission side Before you put the new axle in?

@AutomotiveDysfunction 5 месяцев назад

not sure 2007 Sorento is RWD based vehicle

@BugzKiller 5 месяцев назад

@@AutomotiveDysfunctionI got the selector for four-wheel drive as well though

@stacyellis135 Год назад

If the CV joint on a Kia Sportage were to suddenly break going 80 mph, could this cause the car to flip front end over back end?

@patrickjohnson195 Год назад

Yea i would say so if its top heavy 80 mph you will at least spin you out possibly into other lanes but you usually get a decent ticking noise before it fails...