How To Properly Disassemble A PSP 1000

Подписаться 7 тыс.

Просмотров 3,1 тыс.

50% 1

In this video we go over all the little details in taking the PSP 1000 apart. With each screw detailed and documented on where it goes.
Channel Support Affiliate Links For Everything Below:
Electric Screwdriver:
s.click.aliexpress.com/e/_Dmq...
Manual Screwdriver:
s.click.aliexpress.com/e/_Dke...
Tweezer Set:
s.click.aliexpress.com/e/_DCg...
-----------------------------
Time Codes:
-----------------------------
00:00 - Introduction
00:25 - Tools Needed
01:37 - Testing The Console
02:46 - The Disassembly Start: Outer Screws
03:46 - Analog Screws
04:55 - Screen Removal
05:52 - Sub-Frame Screws
06:29 - D-Pad Screw
06:48 - Face Button Removal
07:25 - Charging Port Screw
07:39 - Wi-Fi Antenna
08:13 - Speaker Removal
09:23 - Motherboard Screws & Safe Removal
11:08 - RF Shield & Card Retainer Screws
12:13 - Unused UMD Screw
12:19 - UMD Door Removal
12:50 - UMD Drive Screws
13:32 - New Shell Reassembly
-----------------------------
Discord: discordapp.com/invite/5bsGzq7
-----------------------------

Игры

Опубликовано:

7 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 21

@justincredible5406 Месяц назад

Phenomenal video! So much care and fine detail explanation! Thank you for your motor skills, patience and presentation! :)

@Arayadavido 2 месяца назад

I love how sony forced their engineers to make us a harder time to dissamble their products. At least it's enjoyable haha. Keep going I'll more than pleased to se the PSP smokey mod

@TotalKommando 2 месяца назад

I think they were being extra careful with their first handheld, its not that bad but its also pretty old. 2000/3000 became much simpler in terms of how all the parts are sandwiched together.

@demijebus6831 Месяц назад

Quick tip for tweezers slipping. Dip the tips on an extra set in plasti dip or flex seal. Just make sure to rough up the tip for adhesion and clean in a degreasor or 99% iso before dipping.

@TotalKommando Месяц назад

That would be the optimal way, I personally would have just threw on some shrink tube, but the idea behind the tutorial accessibility. Not everyone has shrinktube or plastidip laying around.

@demijebus6831 Месяц назад

@TotalKommando absolutely. It is just something that I did a while back to some of my tools, and it has been tremendously helpful for me when building computers, models, or just trying to prevent marking up surfaces. I thought I would share.

@TotalKommando Месяц назад

100% not discouraging you at all, I actually have been wanting to buy plastidip spray or in liquid can form for a while, sadly where im at atm its no where to be found, i tried flexi but found it to suck lol

@demijebus6831 Месяц назад

@TotalKommando all good. That sucks that you can't get it where you are. Thanks for all your awesome videos. They are very helpful.

@Jr-ff2tq Месяц назад

Can you please show a video where you put the housing clear case on it. It will really be usefull for me thanks😊

@TotalKommando Месяц назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yTVGM6Nlr40.htmlsi=vl_jjzQ-w_pTTJwM : )

@TotalKommando 3 месяца назад

Part 2 - Shell Swap Video Is Out: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yTVGM6Nlr40.htmlsi=vl_jjzQ-w_pTTJwM ( Part Cleaning, Reassembly & Third Party Shell Tweak )

@huutidang7662 3 месяца назад

keep it up, bro

@xroyal2179 3 месяца назад

That is way too hard

@HD_6350 Месяц назад

Awesome video, you convinced me to but a clear shell and try to fix my old psp 1000. Just a question, because I miss the metal clip which holds the R button you remove at 4:28. Can I buy it somewhere? Because I managed to find some missing components from aliexpress and ebay, but not this one

@TotalKommando Месяц назад

Now that you mention it, I have never seen that part being sold, you can get away without it, you could try to secure it into place with tape on the edge : ) Good luck

@HD_6350 Месяц назад

@@TotalKommando The button works without the tape, so yeah, that metal piece is not needed. But now I have another problem. I've purchased a new power board. I connected it to the board with the ribbon cable, but when I try to plug the ac adapter and push the switch the system doesn't turn on. If I short some pins near the mechanical switch I can see the green led, but the system doesn't turn on. Could it be defective?

@TotalKommando Месяц назад

try adding a thin piece of tape on the ribbon, it may need extra pressure or its just defective : |

@stevexanny 2 месяца назад

Watching this a second time, I'm surprised a video of this quality has less than 1000 views! I got 2 questions: Can i use triggers from a psp 2000 or 3000 on the 1000 model? I can only find triggers in black for those 2 newer models Also, the silver frame that goes around the psp, would i be able to remove that after only removing the subframe? Thinking of buying another frame and spraypainting it back to give the PSP an all black look

@TotalKommando 2 месяца назад

Yea : ( Triggers no, slim ones will not fit, I will have a video in the future show casing how to paint both the triggers and outline. I too want a black trim for the 1000 lol To avoid breaking anything, remove it after you remove the motherboard and power switch board. The top trim will be the finicky one

@stevexanny 2 месяца назад

I'm excited! Hopefully the videos are all out by august so I can take my PSP on vacation with me lol :) but i think the screen mod will be enough at first and the triggers/frame can be done at a later time@@TotalKommando

@TotalKommando 2 месяца назад

@@stevexanny Yea Im trying really hard to release one video a week, hoping to double the production next month once I take my "vacay" the ips one im working on as we speak is one of the most time consuming ones.