How To REMOVE a FLYWHEEL on a Briggs and Stratton Riding Lawnmower engine motor

Подписаться 61 тыс.

Просмотров 254 тыс.

50% 1

Jeff's Little Engine Service gives another "backwoods" backyard tutorial on HOW TO REMOVE A Briggs and Stratton FLYWHEEL and ALTERNATOR on a CRAFTSMAN Riding Lawnmower Briggs motor. Flywheel TORQUE SPECS. and removal procedure. Replace Bad ALTERNATOR due to no DIODE. caused a BATTERY DRAIN. Dead battery. Problem fixed! Impact Wrench used, grinder, flywheel Puller removal tool. Covers many different Horsepower engines and motors models
Music by my band BonzaiRod "George"
Donations are greatly appreciated and help me make vids, just click the Paypal link below. Thanks!
www.paypal.com/cgi-bin/webscr...
copyright 2017 Jeff's Little Engine Service
Jeff is NOW Sponsored by GRIP tools! They help me help you! Check them out!
gripontools.net/
PLEASE KEEP IN MIND when you are watching my videos: I am showing you the least expensive, quickest "backyard" methods for repairing or servicing your lawnmower. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. ALWAYS WORK SAFELY TO AVOID INJURY. Thank you for watching!
Jeff

Опубликовано:

20 мар 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 177

@rickeveleigh8908 4 года назад

Thank you! The bash the socket wrench with a mallet trick just helped me get the nut off my one. No other video I could find had this tip.

@jamescrossan2548 5 лет назад

Man this guy is destructive.

@floridalottery3134 3 года назад

holy shit right

@Michaelc-gn3eg 2 года назад

Attempting a repair my mower to get it ready for the mowing season. Thanks for the help

@Alpha1545 6 лет назад

The diode makes half wave dc voltage. More than enough to charge a battery. The battery does not care how unfiltered the dc is it just cares that it is dc. Remember the fly wheel and it's magnets create ac at the tap so you need the diode to rectify it to dc. Just thought you wanted to know. Great video and nice puller for those types of situations.

@knighthawk86855 4 года назад

I use a steering wheel puller, so all the force is on the crank shaft, I also use a impact air tool, but best idea is to spray pb blaster on the crank shaft to clean up the area between the shaft, and the flywheel..... Not an easy job, you did great.

@JeffsLittleEngineService 4 года назад

good tip! thanks friend

@stephenc4161 3 года назад

My biggest laugh all week , whacking the flywheel nut lololol... Great video.

@MrRunnerdog 4 года назад

Your humour throughout this is right up there with bill but !!

@BritishBeachcomber 2 года назад

That's a good way to wreck a ratchet wrench. The cheap ones often have plastic parts inside.

@davidphillips2259 3 года назад

Crazy little engine Jeff lol

@mowerrepairshopfortscottkansas 6 лет назад

grate video Jeff

@lennybaldacchino Год назад

u could heated the screws loll, or WD40 i like that brutal, hahaha great job loll

@4spdlife857 6 лет назад

a steering wheel puller works as well

@neilmacleod5371 5 лет назад

The old rope down the cylinder through the spark plug hole , then turn the shaft till it tightens works good to stop the shaft from turning

@JeffsLittleEngineService 5 лет назад

that always makes me nervous.....

@southernbucks1687 7 лет назад

That is absolutely NOT the only way to get the flywheel off.. There are several ways to get them off.. Easiest way is an air hammer or a pry bar an hammer..

@ezraducat4826 4 года назад

Southern Bucks it’s way faster and easier

@calforman 2 месяца назад

@@ezraducat4826 What are you Talkin about ?? SOUTHERN BUCKS ??

@neilfroggycrompton2466 6 лет назад

If the module was ok couldnt u have just soldered on a new diode to the wire (with correct polarity) & using correct type of diode?,do u know what type diode is?

@armyvet4081 7 лет назад

This is why you should never let a anything with a small engine set outside.

@sawyerbennett8227 5 лет назад

Jerome Cook some people don’t have a choice

@BigAlWillis 3 года назад

Can also remove spark plug feed in some nylon rope into the spark plug hole to jam up the piston. It keeps the motor from spinning. After you loosen or tighten the bolt just remove the nylon rope.

@JeffsLittleEngineService 3 года назад

yes but I am always worried about bending a rod doing that

@JoeBlowski 3 года назад

@@JeffsLittleEngineService I think bending a rod is impossible when using the rope method on any engine, because I think they are much stronger than the grip of the fastener... unlike the chance of bending relatively fragile open valves on any 4 stroke engine if the rope is not inserted in the particular stroke to have them closed which is either before the top of the compression stroke or after the top of the power stroke depending on whether removing or installing the fastener. Make sense?

@Honestandtruth 2 года назад

@@JeffsLittleEngineService You so damn Funny 🤣😂 Just hanging hard

@obfuscated3090 3 года назад

Much love for manual impacts for where they shine (ancient motorcycles which have JIS case screws...) but a light electric impact is far better for jobs where you DON'T want to bash the part you're removing. If you already own a harmonic balancer or steering wheel puller the good ones are much stronger than the cast Briggs/AYP/whatever part and Grade 8 bolts are cheap.

@somethingtrulyhorrifying 3 года назад

A tip for those having trouble holding the flywheel still. A pipe wrench or pair of vise grips clamped onto the drive pulley underneath and resting against the frame/axle as a blocker. But I already took the pulley off, and I was bending and breaking stuff trying to hold the sucker still just trying to remove the nut. Then I dug out the almighty air impact wrench, Bob's your uncle it zips the nut off with EASE without holding the flywheel. And then I stuck the flatbar underneath the flywheel and used the convenient dimple in the center of crankshaft for the air hammer that I also dug out. Just wish I had enough sense to do that before I broke a couple teeth on the flywheel :/ hope it won't cause starting issues, but at least everything's loosened for the next _go round_ if I need to replace.

@spider78612 5 лет назад

The Silkys at 12:35 were my favorite part!

@clydeeastside 2 года назад

Very helpful

@JeffsLittleEngineService 2 года назад

Glad it helped

@donaldlee6699 2 года назад

Have you done a part 2 to this video? Thanks for the video! I just subscribed!

@JeffsLittleEngineService 2 года назад

not exactly but I do have other videos with this mower here is one ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-4NsBvCXKvwk.html

@johnwade5747 6 лет назад

Myself, I would have laid 3 five sixteenth nuts on the screwheads and mig -welded down thru the centers .(OR.... Use a sharp chisel to cut the center out of the screen to access the nut. )

@BN_Garage Год назад

I got a 84 LTV/10 identical to yours. My alternator is a full circle with points and condenser underneath having a similar issue to you.

@jrac863 4 года назад

pulling flywheels are like pulling ball joints.You never want to put that much pressure on the puller .After u have your puller set up tighten it up then hit as close as u can to the center of the flywheel with an air hammer .This method is the easiest best method to remove all types of flywheels .Ive pulled100s of flywheels like that

@JeffsLittleEngineService 4 года назад

great tip!

@officerkrupke4966 Год назад

After tightening puller to put strain on flywheel, apply heat to flywheel hub until it pops off shaft.

@brianhudson2265 Год назад

Strap wrench works good holding the fly wheel still

@JeffsLittleEngineService Год назад

Good tip, That is the best way I think

@DebbieBritt-kz2tl Год назад

😂 that's what I feel like doing to my lawnmower whack it with a sledge hammer 🔨

@JeffsLittleEngineService Год назад

It does make you feel better sometimes

@thebackwoodsboysgarage9144 3 года назад

10:48 2 get a flywheel off I just take a pry bar and put some pressure on it and and hit it with a hammer it comes right off

@Mike-su8si 3 года назад

After a hour or so yeah that way does work

@courtneyhall7140 4 года назад

brutal,absolutely brutal.

@mongomay1 5 лет назад

your impact driver has a square end under the attachment cap you can use on sockets.

@MrMackAtack 5 лет назад

Thank"s for this not a lot out there about this specially for us comon folks w/o all the fancy tools just working on the ground. 👍

@mongomay1 5 лет назад

@@MrMackAtack I do all my work on the ground, layout two or three sheets of 3/4" plywood, a piece or two of carpet to save on my knees....L grew up on horse farms and made friends with a guy that turned out to be a self-taught mechanical genius back in the 70's-80's; went to Industrial Systems Tech college in 2000, been working on things as a kid without knowing from a single parent home, everyone that worked on our car I would be in their pits if not in school. Tried to learn anything I could from anyone that knew how to do something by watching them, then practicing.

@williamblack7268 3 года назад

isn't there a flywheel lock item for doing this? And a short bunji chord to pull that cable out of your way?

@gordonsellards992 Месяц назад

Obviously he’s no millwright 🙈

@stubeast4031 Год назад

You got downright medieval on that.

@JeffsLittleEngineService Год назад

Thank you

@garyweldon8188 2 года назад

Damn guy, don’t make me laugh any more!!! My ribs hurt!!

@aaronzuccolotto5406 6 лет назад

I fell asleep watching this.

@sindessaorellia 3 года назад

importance of wearing gloves - i was following this yesterday- removing the flywheel - two broken fingers and a bruised thumb - felt good .

@RatSleds 6 лет назад

JESSUS lol but have to AGREE THEY ALL NEED THAT lol GIVE IT TO IT HA like my old UNCLE use to say if you cant get it off with that USE A BIGGER HAMMER! ha !!

@antongirdeux07 5 лет назад

shoulda just cut a flat line into the heads of the screws and used a flat head screw driver

@jakeschaffer1431 3 года назад

I agree. It was nails on a chalk board watching him pound on the head of his engine. Im sure that was good for it

@Mike-su8si 3 года назад

I done that a ton of times

@harleyvannray8583 2 года назад

Or vice grips...

@elizabethannfarrow1971 4 года назад

I was just going to say you could have used 1 of those flat crow bars to hold the fly wheel in place while get'g the bolt off and gently use the crow bar to pop the flywheel off.I just watched this in another video.I am lookg for a video on how to use a wheel puller.In another video the guy broke his wheel peeler cuz instead of doing it the old fashioned way with a ratchett he used an impact tool.

@phonasserviceconte4059 7 лет назад

Disassemble it with dynamite ... maybe do it before

@MetalEric12 Год назад

A little off topic but I recently had a crack in my flywheel but it's a newer style flywheel with no fins. Is it possible to rig an older flywheel on?

@JeffsLittleEngineService Год назад

not sure

@ken3700 2 года назад

Put a pipe wrench on the shaft under the deck..

@TheGallant67 5 лет назад

Try using a pry bar and a hammer

@fredcarmichael9529 5 лет назад

do you ever clean the parts

@JeffsLittleEngineService 5 лет назад

Nope

@Vic7075 3 года назад

Did you ever consider liquid wrench penetrating oil ??????

@JeffsLittleEngineService 3 года назад

good tip! I should use it more often.. however, my patience in letting it soak is always difficult!

@Mike-su8si 3 года назад

That whole stator looks shot and fried from old age. My stator wire goes from that to the rectifier then to the ignition relay from that to the battery the ignition solenoid to the ignition relay to the battery. I disconnected all safety buttons on each riding mower.

@tonyjackson256 4 года назад

It was a good comedy watch

@ScreeminMeeme 11 месяцев назад

Love your videos. They're very helpful. You don't edit out mistakes or the times when Murphy's Law kicks in and things don't go as planned. Happens to me ALL the time. Thanks.

@JeffsLittleEngineService 11 месяцев назад

I appreciate that! Thanks for watching

@carrollledscarrollleds2032 7 лет назад

that one looks smoked....... and that one looks smoked lol

@Crlpope 6 лет назад

I lost the flywheel nut on a 5 hp Briggs and Stratton motor on a old Craftsman tiller it is not a 5/8 too large and not a 1/2 inch too small do you know what size it could be or where I can buy one?

@JeffsLittleEngineService 6 лет назад

I think it is a unique nut sold through Briggs and Stratton only. Let me know if you find a common one that will work

@Crlpope 6 лет назад

Thanks I will keep look looking I just bought one from a man that repairs lawn mowers he took it off a junk lawn mower and it fit. It is out of stock in all the places I checked and it is some bastard size to rip off people by B&S. I will let you know if I find some common part!

@JeffsLittleEngineService 6 лет назад

good news!

@zlindauer5315 5 лет назад

thats the size wrench or socket it takes, not the size of nut. for example a half in bolt takes a 3/4 wrench.

@patalexander3702 3 года назад

You sure showed us how to bruise up the engine!

@JeffsLittleEngineService 3 года назад

It can be rough and tumble around here sometimes my friend LOL!

@jimvincenti2324 4 года назад

Use a small Dremel tool

@dariomendoza191 3 месяца назад

why not use an Impact wrench?

@JeffsLittleEngineService 3 месяца назад

Good tip! I did not have one available at the time.

@dariomendoza191 3 месяца назад

@@JeffsLittleEngineService you,r welcome thanks for Sharing

@mainormurillo7254 5 лет назад

Jesus!! LOL I never seen anyone do this type dangerus FIX LOL

@JeffsLittleEngineService 5 лет назад

Lol! Living on the edge

@muffintop420 5 лет назад

You sound like Jack Nicholson.

@monteclark1078 Год назад

Or you can pry up on flywheel and wack the bolt with a hammer. works like a charm

@JeffsLittleEngineService Год назад

Ol skool... Good tip!

@tonyhilliam2407 Год назад

Luckily you didn’t blow yourself up with the sparks going all over the fuel tank!!

@shannonbrooks8834 3 года назад

I do not see how the hell a puller works on some of these Motors. You get a steering wheel puller just too find you need too pre drill the holes in the flywheel too get the puller too fit. Hammer, and pry bar, with some trans fluid and acetone mixed. Let it soak a bit at the shaft, and beat the hell out of it. OK, tap it a bit.

@jennygreer9371 3 года назад

Dude take the bolt or nut off that holds the flywheel completely off if its a nut screw it back on the crank shaft level with the shaft or screw the bolt in a little put A big screwdriver under flywheel pull up hit bolt with hammer. Dont need the flywheel tool

@sarcolo3829 4 года назад

I tried using a clutch / steering wheel puller it tore through the puller ...

@JeffsLittleEngineService 4 года назад

yikes,

@keithcerce8445 6 лет назад

920 tap the top center w/your hammer

@banjobenson9348 3 года назад

everything looked a little smoked on that mower, including the chickens

@andymilligan9075 4 месяца назад

😂 don’t take got mower to this guy.

@fatimaclark6449 5 лет назад

My 11 year old son fix iwere ridding mower

@brianmanning9890 4 года назад

How bout the half of the stator that's missing wow

@sarahashley3234 3 года назад

The half circle stator is normal for a machine with no lights.

@southernbucks1687 7 лет назад

You can clearly look at the coil an tell it is not a points type ignition...

@paulwary 5 лет назад

Don't force it, just get a bigger hammer.

@joeryan2299 2 года назад

Why not remove the end of the impact driver which exposed a 1/2 inch drive and put your socket on it

@4spdlife857 6 лет назад

good way to loose a finger if that wheel would have grabbed with your hand in the way like that ud be a digit down

@Vic7075 3 года назад

Have you considered a penetrating oil liquid wrench.

@ezraducat4826 4 года назад

Hey there is another way to pull fly wheels. Just put a pry bar underneath the flywheel and with the nit flush on crankshaft, smack the nut with some force and it will come right off

@johnwilliams3725 2 года назад

What happens when flywheel is stuck so bad and pulls the bolts on the puller into?

@JeffsLittleEngineService 2 года назад

If you can hit the nut or bolt that holds the flywheel down with a 3lb. or so sledge hammer (or are able to use a "knock-off" tool) you may be able to shock the rust loose if you know what I mean. Of course always be careful not to hit or damage the flywheel

@johnwilliams3725 2 года назад

I have done that with one puller while the flywheel was under tension by hitting the puller bolt, I have the genuine B and S puller that I used a heavy punch thru the center hole and under max tension any more tension and I am parting the puller bolts I have ordered some grade 8 bolts for the puller to try IF the puller will stand it thanks for the reply

@johnwilliams3725 2 года назад

@waynesummers921 5 лет назад

I am sure glad u don't work on my mower -- shade tree- frick and frack

@JeffsLittleEngineService 5 лет назад

lol!

@allenmckinney9533 6 лет назад

That nut should've been 15/16". That's what every birggs I've worked on was.

@JeffsLittleEngineService 6 лет назад

you are probably right!

@johnwade5747 6 лет назад

15 Sixteenths is the WRENCH size, and OLD engines with rope cups are left hand threads.

@calforman 2 месяца назад

You can Tell Amateur all the way ... 1 Do not be hitting gas Tank or frame, Take a Longer wrench ........... 2) Secure the Fly wheel, below Engine by putting, a wood stop, or Vise grip by the bottom . instead of Flywheel Fins,which will break . 3) get that Cable out of the way to work on it ...

@jumpingjo3689 3 года назад

We know you put that impact on the flywheel nut.

@JeffsLittleEngineService 3 года назад

lol!

@AlabamaT1CK Год назад

How sad is it that this video has +200k views😢

@settripsbunch 5 лет назад

beware of the ratchet method for taking off the flywheel bolt...you have to know the rotation of your engine if you turn the engine backwards you could cause problems

@JeffsLittleEngineService 5 лет назад

I turn them backwards all the time

@settripsbunch 5 лет назад

I get that yet it is not a practice to teach when working on any engine...complicated or simple..was researching doing a timing belt on an 02 focus it was said dont turn the engine backwards...to sum up what Im saying know your engine if you do decide to rotate it backwards not everyone is experienced as you are.

@Sevalecan 5 лет назад

@@settripsbunch My understanding in certain timing setups, the belt or chain can lose tension when the engine is being turned backwards, causing it to skip time or otherwise hang up inside the timing train. The Briggs motors that I've torn apart all have a gear driven camshaft, and should not be susceptible to this problem. Just my 2 cents.

@ianstewart5297 10 месяцев назад

Is there something wrong with this video or is it me. ? Spit screen why?

@JeffsLittleEngineService 10 месяцев назад

should not be split screen

@lesstime1678 6 лет назад

what is that? a MOTOR or a ENGINE !,also,, a ALTERNADOR or a GENERATOR?

@JeffsLittleEngineService 6 лет назад

jose tavares Good questions... an engine is a gas powered component. a motor is an electrical component. Both alternator and generator generate electricity they just do it differently. In an alternater system the magnets rotate and the copper coil is fixed in place. It is just the opposite In a generator, the magents are fixed and the copper coil rotates.

@yardlimit8695 6 лет назад

jose, it's an alternator

@josephdeffendoll3056 5 лет назад

Please buy another Mower.

@michaelpalmer937 4 года назад

Pretty handy If your know how to....What's that ! English Mik!

@maxx_bxx8365 5 лет назад

Omg what is this guy doing lol

@randytingle2416 6 лет назад

It's not brain surgery

@reginabogdan1120 4 года назад

❤❤❤😘😘🥰🥰💋💋💋💋💋💋💋

@kendexter 8 часов назад

would not drop off any

@Honestandtruth 2 года назад

I got a Solution...... Get a brand new Lawn mower tractor 🤣😂

@JeffsLittleEngineService 2 года назад

but then I would have nothing to fix...

@Honestandtruth 2 года назад

@@JeffsLittleEngineService Just kidding man.... Sometimes..... We have to joke around....... In today's World is too much Stresses and issues Everywhere.... And Lazy people are everywhere too

@philliphall5198 Год назад

There is no excuse for breaking fins If you watch others you’ll learn alot

@JeffsLittleEngineService Год назад

sometimes the plastic is so brittle from overheating the fins break just when you look at them.

@wwilliam51 5 лет назад

poor workman ship,,

@JeffsLittleEngineService 5 лет назад

it's only a lawnmower ... not a Ferrari

@michaelsullivan6854 Год назад

If you got this far, what harm is a couple of purple Herman's on your hands ? 🤬

@sevengarcia6355 3 года назад

These nuts 🤣🤣🤣🤣🤣🤣

@TefCom12 2 года назад

This was painful to watch. Hammers and cheater bars are not,.. never mind.

@howitsnotmade6323 4 года назад

A normal screwdriver would have probably worked

@deanhenthorn1890 3 года назад

That’s not how you use that tool.

@daveenns1119 3 года назад

..I think this video was meant to be a joke.

@JeffsLittleEngineService 3 года назад

yep

@whatever895 4 года назад

freak

@JeffsLittleEngineService 4 года назад

you know it

@whatever895 4 года назад

4 days ago freak

@danieltaylor9761 Год назад

This is how not to do it. He simply could have snipped an opening for his socket. Bend the sharp edges down. Hammers in my opinion do not belong in a mechanic's tool box. They always lead to problems. P.S. Always turn an engine clock-wise. Never Never counter clockwise. A strap wrench or lg screw driver against the gear teeth to prevent turning to remove the bolt. Duh!

@JeffsLittleEngineService Год назад

Why do you say to only turn the engine clockwise? My 3lb. lump hammer is my favorite tool.

@garrydonnelly6433 3 года назад

That was the most amateurish effort I have ever watched. Bloody embarrassing.

@warrenpeas 3 года назад

talk is cheap. post videos

@haroldwonder446 29 дней назад

Sorry but not a good video for a DIY situation. Need to be more direct and accurate in your presentation to leave a feeling of you know what you are doing for those wanting to follow your direction.

@JeffsLittleEngineService 29 дней назад

Thanks for the tips!

@69hareman1 4 года назад

butcher!!!!!!!!!!!!

@jonlambshead5115 Год назад

My God Jeff, I Cringed When You Was Hitting The Ratchet And Slipped, Nearly Taking Out The Air Cleaner. Not Good Practice To Do That Sort of thing To Remove The Nut. I Had To Close My Eyes When You Put That Extension Bar In Between The Flywheel Fins and Torqued Down On The Puller Nut. I Thought For Sure You Would Break The Fin Off. Another No No. Some One Has Been In There Before and Broken Half Of It Off and Put It Back Together Like That. That Is Supposed To Be a Complete Round Alternator . You Only Had Half Of It There. If You Broke The Fins On The Flywheel It Can Become Unstable and Also Not Cool The Engine Properly. Be Careful Folks Not To Do This. ( BAD Practice )

@JeffsLittleEngineService Год назад

good tips!