How To Remove Rust With Electrolysis In Six Easy Steps

Подписаться 109 тыс.

Просмотров 1,2 млн

50% 1

Hit the Join button for Channel perks like early video access, shoutouts, and priority comment replies.
/ @ajrestoration This is a step by step video on How To Remove Rust With Electrolysis In Six Easy Steps.
Intro : (00:00)
Items Needed : (00:14)
Step One - Prepare the Anode : (01:09)
Step Two - Prepare the tool : (02:02)
Step Three - Insert Anode and Cathode : (03:19)
Step Four - Prepare the Solution : (04:03)
Step Five - Prepare the power supply : (04:38)
Step Six -Clean the tool : (07:30)
Here’s the overview: Submerge the tool in a solution of baking soda and water, connect a battery charger, and let it sit overnight. By the next day, the rust will have sloughed off.
The beauty of using electrolysis for rust removal is that you’re not damaging the tool and removing metal. It’s better for the tool, especially if you’re concerned about its value if you don’t go at it with abrasive products. This makes electrolysis the perfect answer for restoring old tools and it's extremely easy to do. Electrolysis provides a very effective way to get rust out of a tool’s crevices and hiding spots.
I have recently wanted to try my hand at removing rust with electrolysis and here is my shot at it.
I have used a No 3 Machine Vice for this method and found great results!
I hope you enjoy the video.
If you have any suggestions for improvement, or compliments share them below! #ASMR
#RestorationASMR
#ASMRRestoration

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 467

@lanedexter6303 2 года назад

Laundry soda (sodium carbonate) works even better than baking soda (sodium bicarbonate), but both work. A standard 10 amp 12V charger works fine. I often use an old scrap of rebar instead of a tin can. When the the rebar starts to load up with rust, I see the current drop. I clean the rebar on a wire wheel, then put it back and see current increase.

@lanedexter6303 2 года назад

@Common Sense Realist I usually start with 24 hours in vinegar for an old axe. A hit of the wire wheel after that, and I can see the temper line. Electrolysis or Evapo-Rust (chelation) comes after that.

@neomateo944 11 месяцев назад

Scrap Stainless steel works well and can be wiped clean. Also 12v (18-22v) solar panels work by themselves as power source.

@lanedexter6303 11 месяцев назад

Thanks, I’ll try stainless. Might even have a solar panel around here.👍@@neomateo944

@cody2097 7 месяцев назад

@@neomateo944stainless should NOT be used with electrolysis!

@dukerton15 6 месяцев назад

@@cody2097 Why not

@seekrengr751 3 года назад

If you sand a small area with fine sandpaper where the cathode wires are attached to the tool to expose bare metal, the time required will decrease due to a better electrical connection; iron oxide conductivity is poor. Also, if you use coated wire except for the connection to the tool, the water electrolysis (hydrogen generation) will be less. Notice the bubbles on the wires to the tool and the anode. Nice choice of anode, the can will allow a good electrical path to most of the tool. If you could use a large can that the tool completely fit within, that would work even faster.

@AJRestoration 3 года назад

Thanks for the tips. I will keep this in mind.

@VictorGarcia-cb2xp 2 года назад

Felicidades que exelente forma de presentar las herramientas y muy bien explicado..aunque no se mucho de lenguaje inglés..pero entendí todo..mi admiración y respeto...un gusto ver su video...un abrazo patrio!1

@zube6996 2 года назад

Thanks for this informative video. I guess some of the commenters missed the fact that this video was all about how to make and use electrolysis to remove rust, not restoring the tool.

@taunteratwill1787 2 года назад

And failed at that as well. 😎

@kena6858 2 года назад

I do this procedure but instead of baking soda I use super washing soda as it to me is a better option and instead of a power supply I use a battery charger set to 2 amps. The sacrifice piece is a piece of rebar.!

@danielrebolledo1479 2 года назад

Can you make a video please

@Pedro72740 2 года назад

@@danielrebolledo1479 I shit my pants?

@gregorymacneil2836 8 месяцев назад

I use washing sofa too - it works better!

@Equestrianballer 2 дня назад

@@gregorymacneil2836when you add the washing powder to the water you are creating the bicarbonate again in situ. It’s always going to be bicarbonate

@Marcelo-56 3 года назад

04:00 The mixture of water and bicarbonate must be done before (for a complete dilution) and with hot water to improve the process‼

@AJRestoration 3 года назад

Makes sense!

@savage22bolt32 2 года назад

Thanks for the great educational video, and a huge thanks for not ruining it with crappy background music. I don't know why some people are compelled to add annoying background music throughout the video.

@AJRestoration 2 года назад

Thanks for watching!

@melvis2017 9 месяцев назад

Because they think they are smart 🤣🇩🇰

@JuniorFarquar 6 месяцев назад

What about luve Led Zeppelin 1973, though?

@britishprofessor9957 2 года назад

Excellent video. I use viniger for 24 hour it works well. There will be sludge in the viniger. I restored all rust damages tool to perfect condition.

@AJRestoration 2 года назад

Thanks for sharing

@traceyl.cumberland225 3 года назад

For those of you watching this video, you should be using "Washing Soda" (sodium carbonate) not "Baking Soda" (sodium bicarbonate) for the electrolysis process.

@AJRestoration 3 года назад

Agreed, both has similar results. All it does is make the water conductive, even using regular dishwashing liquid will work. I have used baby shampoo before with good results, and it smells good. ;-)

@kennedy6971 3 года назад

I dont know that it matters much if its carbonate or bi- carbonate.. Either works great. Just dont use table salt because that produces chlorine gas which can kill you..

@andyloescher2401 3 года назад

You can make sodium carbonate easily by just heating sodium bicarbonate at 100 degrees Celcius

@Midnightgamer00 3 года назад

@@andyloescher2401 are you sure it is 200C and not 200F? thought it was 200 Fahrenheit for 1 hour

@andyloescher2401 3 года назад

@@Midnightgamer00 damn oops. I meant 100C

@justhelper4728 2 года назад

So beautiful sound or rain , i love this

@raptors3164 3 года назад

I've always wanted to know how to do this, and you made a video on how to. I Liked and Subscribed, Thank you for creating this video and for sharing your talent. 👍👍👍👍👍

@AJRestoration 3 года назад

Thanks for subbing! I am glad I could help you out!

@S-O-T 2 года назад

Good video 😎 Get an old car battery charge it up pour all the acid out and use a paint brush to paint it on, Dissolves the rust instantly Removes every trace of it Or soak in vinegar for a few days, I've restored loads old tools I Found in a quarry using white vinegar 😃

@jjcharlstonisaac6222 2 года назад

Good information. Better if had dismantled and done the proses.thank you..

@crazyDIYguy 3 года назад

Strangely soothing to watch...🙄😳

@FRANKBURNSONE 2 года назад

So, were you able to remove the stuck screw?. I have noticed parts that are close together don't seem to get as clean as the rest of the parts? I would try a little heat first because it's easier and faster. Then you can do a complete teardown. Depending on if you are just wanting a working vice or complete restoration. Thank you for taking time to post this.

@somaaelsapak6361 2 года назад

Great video thanks sir for that

@collera05 3 года назад

I have a lipo Charger that's supports DC charging up to 18volts. Will that work?

@AJRestoration 3 года назад

Yes, just keep a close eye on the charger so it does not overheat. If the current is too high, dilute the electrolyte by adding fresh water.

@lionelperez2856 2 года назад

Hola. No deberian estar aislado por donde llega y sale la electricidad??? Por que en la solucion seria la parte conductiva.. si es asi.. por que conectas un polo a la lata y el otro a la pieza??

@cecilcooper6210 2 года назад

I liked your opening!

@Jango975 2 года назад

Aj restorations what the voltage on the power supply how many Volts it requires when placing in water solution?????

@grantbuchanan7295 2 года назад

Try watching the video

@kanishka.b8550 2 года назад

Can we use a copper wire for the connections?

@msk3905 2 года назад

Just curious what will happen if I don’t confidently add the degreaser because I typically add nervously?

@mb4lunch 2 года назад

So, you confidently speak only one language?

@Alazim7890 2 года назад

@@mb4lunch what do you mean?

@mb4lunch 2 года назад

@@Alazim7890 I was replying t o Michael S, who was making fun of the creator of this video for his lack of language skills. And I was like... Well how many languages do you speak bruh? The guy who did this vid probably speaks 2 or more! That's what I mean.

@Dancing_Alone_wRentals 2 года назад

tHank you, That was fun watching

@asangamendis6105 2 года назад

Pls advise can we do this process on brass items to get more shiny 🙂

@andre-michelgoulet6933 2 года назад

Brasso?

@robertlilley4370 Год назад

So what is happening I followed the steps tested my car charger prior to doing it I get 12vdc when I connect it to the wires coming of the can and the wire coming off the tool the power supply drops to maybe 1 Vdc

@pepaw Год назад

Finally, someone who isn’t a pssy always giving warnings

@thegreyman7449 3 года назад

Nice job mate.

@AJRestoration 3 года назад

Thanks for the visit

@restaurandocoisasvelhas 2 года назад

Very good friend. Hugs from Brazil.

@jeanguycanuel3373 3 года назад

Excellent....vidéo intéressant.😉👍🏻

@AJRestoration 3 года назад

Thank you very much

@johnjohns2333 3 года назад

Very cool vid!

@AJRestoration 3 года назад

Thanks for the visit

@rtisom 9 месяцев назад

This is very interesting and enjoyable. Can anyone comment what is the chemical composition of the fluid in the electrolysis bucket after the procedure, and how can it be safely discarded? (It looks a little unwholesome). Thanks

@accuwau 9 месяцев назад

to my knowledge (which is not too professional) all this is doing is creating iron oxide (the unsavoury black goop) and some gases. one thing to note is NEVER EVER use stainless steel as your anode or else youll create hexavalent chromium which is a neurotoxin and carcinogen among other things, and thatll need to be professionally handled as toxic waste haha. so as long as youre using the correct metals and doing this in a well ventilated area youre all good to dump it whereever, if youd like you can be doubly safe and dilute it with some hose water haha. if youre really unsure you can contact your local authorities or waste management wherever you are and ask them about the proper disposal here. with any home chem as silly as it sounds youve gotta do a ton of research to make sure youre doing it right and not making something toxic.

@rtisom 9 месяцев назад

@@accuwau thanks - very informative and helpful

@WillemLuntungan 2 года назад

Thanks

@carlm6334 10 месяцев назад

What type of wire did you use?

@bouser210 2 года назад

Nice!

@juanpina5983 6 месяцев назад

Thank you master 🙏🏼

@AJRestoration 6 месяцев назад

You are very welcome

@marcelozabala1086 2 года назад

Hola saludos desde Argentina, pidrias habilitar los subtitulos, mi ingles no es bueno, y los terminos son distintos, ya guardé el video muy buena la explicacion muchas gracias, tengo varias fuentes de pc, saludos, ojalá tengas mucho trabajo💪💪💪💪🤜🏻🤛🏻🇦🇷🙋🏻‍♂️te acabo de sumar a los canales que me gustan...!!! 🙋🏻‍♂️🤜🏻🤛🏻

@evelynsia460 Год назад

3 Questions, the anode and cathode should not touch from each other in d bucket? Ur electrolytic subs is only baking soda? Can I use hanger wires for conduction?

@AJRestoration Год назад

No they should not touch, that creates a dead short and could damage your power supply. Yes you can as long as it is conductive it will work.

@user-sj8uq5sk7p 7 месяцев назад

Great content !

@AJRestoration 7 месяцев назад

Thank you! 😊

@ravikantsoni4334 2 года назад

Very nice :-)

@johnm2213 2 года назад

If you left it in the solution longer would it have removed more rust? Will it ever get all of it?

@YOUR_Bro515 3 года назад

This is cool

@AJRestoration 3 года назад

Thank you Shanna!

@mostafaswiedan6291 3 года назад

Now i'm asking What had been happened to this can that you used it as An anode? Did it gain in weight, didn't it?

@AJRestoration 3 года назад

The rust do attach to the sacrificial anode, so in theory it should gain weight.

@bobwhelk2117 2 года назад

How long did you soak it?

@pharaon6718 2 года назад

Can i put 5 rusted wrenchs together on - wire or i need to.do one by one ?! I am new in this sorry

@davidcovington901 2 года назад

Yes can!

@logikami 3 года назад

is that necessary to always spin the table?

@AJRestoration 3 года назад

Yes, it is how I show the before and after

@pasqualepaldino33 3 года назад

Can i use a welding machin for this process if i do Not have a battery charger?

@AJRestoration 3 года назад

You can use a welding machine, but I don't think its a good idea. I am not sure if the welding machine will enjoy staying on for long periods. Also the amount of amps will be too high, unless you use less baking or washing soda in your solution. It will be trial and error, try it on something you don't mind throwing away and first get your ratios ready and then if you want to risk it, go for the part you want to de rust. (I would probably not use a welding machine)

@pasqualepaldino33 3 года назад

@@AJRestoration ok thanks bro i get it. I used less soda and i set up it with 320V but now i think i will stop and i will buy a machine charger. By the way it works the rust comes out and there is the reaction. But for to be sure i do Not make some damage now i will stop it.

@justindaniels17 2 года назад

As soon as i saw Autogear as the brand of the car battery charger i immediately said this guy is South African

@AJRestoration 2 года назад

Spot on! Haha

@soulofartorias9928 2 года назад

why not disassemble it first before doing this? wouldnt this leave rust in the parts where the threaded bolt is covered? seems like sandblasting them after taking it apart would be easier

@asmodeus20 2 года назад

Sandblasting, muriatic acid, wire wheeling all would have likely worked better, but would have defeated the purpose of the video.

@timbenjamin5454 2 года назад

Exactly what I was thinking after seeing the final result. Spray some liquid wrench on the threads, prop it up to let it soak down for a couple hours until its unstuck. Then sandblast it and not only will the rust be gone, but it will look much better in the end.

@cranebeg 2 года назад

And.....it's still stuck 🤣 Removed a lot of rust though, good job.

@AJRestoration 2 года назад

Thank you very much!

@joesaiditstrue 2 года назад

just as a little science experiment, could you do this by running 3x 9v batteries (in parallel) instead of a power supply or is that too low amperage?

@AJRestoration 2 года назад

That would work yes. I think so anyways.

@hayleybmadiggunter6798 2 года назад

You want the amps to be low. The lower, the slower it works, but works better

@hayleybmadiggunter6798 2 года назад

You want the amps to be low. The lower, the slower it works, but works better

@hayleybmadiggunter6798 2 года назад

You want the amps to be low. The lower, the slower it works, but works better

@jdfleo8140 2 года назад

Lube it up!

@felixowens6727 2 года назад

I work sometimes with cast iron cleaning and usually just grind the rust off and It’s been very poor in my work place cause I use a grinder with no guard and it’s hard to reach certain places what would you recommend for cast iron ?

@arturmagnus6674 4 дня назад

And what about tools that still haver some Paint in The Surface besides The Rust? It Will remove The Paint aswell??

@Equestrianballer 2 дня назад

If there is rust behind the paint then yes

@AndrewMDairo 2 года назад

Can i use this in my radiator? There seems to be a lot of rust mixing with my coolant.

@AJRestoration 2 года назад

I cant give you any advice on how to fix your car. For that its better to talk to a professional in the field.

@friendofvinnie 2 года назад

Most radiators are aluminum and plastic today if you got rust but no leak then try a coolant flush and you should be good

@theroyalcrownedtiger2946 2 года назад

When was the last time that car had cooling system flushed and filled ? If one don't remember, chances are it's either been too long ago or has never been done.

@AndrewMDairo 2 года назад

@@theroyalcrownedtiger2946 I haven't had it flushed since i acquired it. Do you think that will solve it?

@theroyalcrownedtiger2946 2 года назад

@@AndrewMDairo : It can help, to do the flush and fill, also don't forget to use 2 bottles of cooling system cleaner 2 shots in 1 go, and lots and lots of water, and warm ups.

@zoozolplexOne 2 года назад

Cool !!

@martinhorner642 4 месяца назад

On electrical supply: Using a 12V supply @ 2A (suggested in another comment) is probably a little overkill, but the higher the wattage (12V*2A=24W) the faster the derusting (just don't get silly with it). I have used an old cheap USB charger plug which is only 5V @ 0.5A(max) which would be 2.5W. It takes longer, but the results are generally the same (with properly sized cathode). Patience with smaller wattages, but if you have the time it doesn't require constant attention. Also, the baking soda (sodium bicarbonate) is only in the water to raise it's conductivity =slightly=, salt would also work (I have used it) but with salt you might have a more immediate chance of an oxide layer form (iron/steels) afterward. A good wash and dry immediately after derusting would probably fix that. Make sure the part is completely submerged. Try to use a flat(ish) cathode with about the same mass as the part. Make sure the part and the cathode are secured in the container and *cannot* touch each other. And remember that wet skin is =much= more conductive than dry skin; best to just use rubber gloves and avoid the water when dealing with this and always respect the potentials involved. I'm not going to say this is a super dangerous process, but it is water and electricity and getting bit sucks.

@Equestrianballer 2 дня назад

The product of using salt in this reaction is chlorine gas. No more suggestions please

@sunil21234 2 года назад

Good

@randyearles9286 3 года назад

good video, thanks for not adding crappy music. a little narrative might be nice also.

@AJRestoration 3 года назад

Noted! Thank you!

@conscience-commenter 2 года назад

What was the elapsed time for electrolysis ?

@AJRestoration 2 года назад

I think it was 24 hours.

@garyjones2582 2 года назад

You can leave it in for a week if u want.. This method will only attack the rust.. After removal and cleanup, you need to spray some lubricant of some type or it will flash rust quickly...

@rosk2detectors 2 года назад

Nice job my frend

@AJRestoration 2 года назад

Thank you! Cheers!

@valahlawnmual4069 2 года назад

Can domestic AC current done the job.

@AJRestoration 2 года назад

No, that can kill you. 5 to 12v DC ONLY!

@MamaBearOf_ 2 года назад

Safer, healthier, and so much cheaper.... White vinegar.... Glass container and cover the rusted object totally. Works perfectly every single time. Even faster if you heat up the vinegar.

@SkitPete 2 года назад

Ok MamaBear...some of us drink Monster Energy for breakfast, not oats...

@jonnyshoestring9368 2 года назад

I'm all for the safer route👍👍 When you say "heat up" is that just a case of putting the vinegar in a pan and heating?

@Savagedownsouth 2 года назад

When I'm doing electrolysis, I use washing soda, and an adjustable power suppy. It's pretty safe, and it works better than I could ever get vinegar to. Can't get it to electrocute me if I tried, and the solution isn't poisonous or bad for the environment at all. But I had the power supply on hand for electroplating. I'm not sure I'd want to use a computer power supply, like in the video.

@bobeskanic8774 2 года назад

@@Savagedownsouth j

@jkreviea 2 года назад

How is vinegar cheaper?

@carizqota4565 7 месяцев назад

Excelente.

@organicvids 2 года назад

Good drill. Makita 18v

@ducphan1946 3 года назад

You mentioned that we need a charger and a power supply. But in the process you only use the power supply? what the charger do in thís process? thanks

@AJRestoration 3 года назад

A charger, or a power supply. Both will work. A 12v battery will also work.

@MDWoodworking 3 года назад

Thank you for your prompt reply

@lisah6451 2 года назад

Great question, I was going to ask the same thing

@jonathonanderson6165 3 года назад

Relaxing

@AJRestoration 3 года назад

Thank you

@deondeetlefs7809 3 года назад

Great job guys!

@AJRestoration 3 года назад

Thank you Deon!

@mostafaswiedan6291 3 года назад

How can i determine which wire is the negative and which is positive in my power supply..? I really do need an answer

@mostafaswiedan6291 3 года назад

Does it depend on colors?

@AJRestoration 3 года назад

If you have a powersupply, the red wire is usually the positive, and black is negative. It is safest to use a multimeter if you are not sure about polarity. I have also explained in the video how you can determine polarity by observing where the bubbles are coming from.

@mostafaswiedan6291 3 года назад

@@AJRestoration what an answer 🤍 Now i almost have the whole tools Thank you

@r3_d2LKG 3 года назад

If youre looking for polarity, you can dip both wires into water without touching and the power is on, wait until you see bubbles come out of one of the wires and thats your negative.

@mostafaswiedan6291 3 года назад

@@r3_d2LKG .that's really helpful Thanks

@mostafaswiedan6291 3 года назад

We have here baking powder Is it and baking soda are the same?

@AJRestoration 3 года назад

Hi There. Unfortunately Baking Powder and Baking Soda are not the same thing.

@whereswaldo5740 2 года назад

Why didn’t you disassemble it first so it cleans up under the immovable movable jaw? And use muriatic acid.

@Andrew-qo6br 2 года назад

How can you disassemble something that is "immovable"? Doh.

@rotten-Z 8 месяцев назад

I assume that the bucket contains a toxic solution after the process. How do you dispose of it safely?

@joaofilho6486 2 года назад

Um jato de areia fazia todo o trabalho em apenas 7 minutos, além de barato o resultado seria muito melhor.

@dr.jonatasbernardes6664 2 года назад

Tem pais que não autoriza o uso de jato de areia pois causa pneumoconiose.

@RegiPavan 2 года назад

o bom e velho suco de limão galego faz maravilhas...

@jeremymcclanahan2389 3 года назад

U ever try sodium carbonate found in Washing soda....the baking soda loses it's punch after a few minutes....it still works but slower

@AJRestoration 3 года назад

Thank you for the information.

@ryangrimm9305 2 года назад

ONE OTHER THING.... Take a utility knife and blades, and SCRAPE OFF the heaviest rust. This goes quickly, and you can see a lot of good metal right away. This will save you a TON of time and other effort. THEN use the electrolysis.

@SuperArgentun 2 года назад

Galon es un litro ????

@user-yy3vs8cw9j 2 года назад

На сутки его опустить в раствор каустической соды , или средство для прочистки канализаций - эффект в разы лучше , и не надо электролиз проводить! Я так делал.

@pj4433 2 года назад

Is that can tin?

@RoyandhisAdventures 3 года назад

Great video! I need help with a project of mine. I need to de-rust the inside of my motorcycle fuel tank. What should I do if I can't scrub the inside of the tank? Please advise. Thanks and awesome video once again!

@AJRestoration 3 года назад

Thank you, The best option is to wash it out as good as you can, let it dry and fill it with Evaporust or something similar. Let it sit for a few days, recover the rust remover solution for another day's use, let the tank dry and I think you should be good to go. I have not done it before, but that is what I would attempt.

@AJRestoration 3 года назад

Have a look at this video, this might help as well. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-y8HEZ-x4-_w.html

@RoyandhisAdventures 3 года назад

@@AJRestoration Great news! It's almost as good as new when I painted it over with POR15 after removing the rust. Thanks for the advice. Wishing you the best!

@mikeherbst1825 3 года назад

For your bike tank, I would clean it out the best you can using your preferred method. Then, to seal it use "Kreme" per the directions that comes with it. It is a tank sealer specifically made for that. I hope this helps.🏍

@tordarbast 2 года назад

I cleaned out a rust wooly 200 l diesel tank for my wheel loader with water up to the rust level and one liter phosporic acid. This acid will take the rust and not so much the metal. After several days the tank was perfectly clean from this rust layer that loosened and clogged the prefilter. The error previous owner had done was to fill the tank to a low level from 20 l canisters. So theres room for condensation. Be sure to check suspicious spots for leakage before you mount it back and fills it with 100 liters of fuel. I made that mistake... I also used some cleaning agent for cleaning toilettes and more that contains phsporic acid. There can be hard to buy real phosporic acid in some countrys for a private citizen. We have in Sweden something called kalkbort its like a thickened so you csn just use a brush and put it on the rusty part and it will cling on the surfaces for some time. Kalkbort is for clenaing off calcium in the bathroom... and be careful use protection for your eyes and hands...

@tonyrebeiro 2 года назад

After your process, wouldn't it be a good idea to Nickel plate it, to get a good finish?

@AJRestoration 2 года назад

Possibly yes.

@kennedy6971 2 года назад

I bet it would be. I have no anodizing experience

@jasonb4738 2 года назад

Wire brush and penetrating oil should have been used. Then it would work and be rust free. 🤣🤣

@whereswaldo5740 2 года назад

IKR. Is that the softest brush you had?

@mishmash6991 2 года назад

WHAT DID THE POWER SUPPLY COME OUT OF ? IT LOOKS LIKE MAYBE A COMPUTER. I WOULD LOVE TO KNOW IT LOOKS SIMPLE TO USE.

@ApocGuy 2 года назад

Looks like LED strip power supply to me...

@brunomoyano8727 2 года назад

Yes it came from a computer i have some of those

@andyajje 2 года назад

Awesome.

@AJRestoration 2 года назад

Thanks!

@andyajje 2 года назад

@@AJRestoration urwel bro.i will try at home

@pete1003 2 года назад

Nice. I use a wire wheel brush. Much easier .

@jmitchell513 3 года назад

I tried this this weekend with a NAPA 6amp car battery charger, I couldn't get it to do anything. The only thing I didn't do was completely submerge it.. do both need to be completely submerged? I tried with out the wire I wonder if that's where it went wrong

@AJRestoration 3 года назад

Usually, you don't need to completely submerge it, It could be that the wires are coated with something and did not make contact. You can also test your power supply and see if it is working as intended. Make sure the parts in the solution do not touch, it shorts out the power supply. Also see if the solution does not have too much baking soda or electrolyte, the stronger the electrolyte the more amps it will draw and some power supplies do not like that. Did you see any bubbles rise from the part you wanted to clean? Let me know if that helps, maybe we can identify what went wrong.

@jmitchell513 3 года назад

@@AJRestoration I actually just ran to Lowes and bought some wire and completely submerged both my old engine part and the sacrificial coffee can.. still nothing! I think this little car battery charger isn't doing right, it only has a red power on light and a green light (to show when its charging an actual battery) I have charged several of my batteries with it but maybe its limited on performing this?

@TuanTran-zp8bt 3 года назад

Unless you got the old charger that not automatic or led smart to it or else you can't use those charger. What you can do with your is use an extra batteries then hook up charger to the batteries and then hook up the batteries to the metal you want to remove rust. That way the batteries will do the work and the charger will charge the batteries.

@jmitchell513 3 года назад

@@TuanTran-zp8bt I found that out after doing some digging! But didn’t know what you just mentioned about using the battery! So basically I could hook up the smart charger to a car battery.. get some alligator clamp an run leads from the car battery to the metal and that would work?

@TuanTran-zp8bt 3 года назад

@@jmitchell513 yes, so use the car batteries to hook up the metal and the reason u use charger hook to batteries so your batteries don't ran out of juice and continue give out engouh power. The charger will charge the batteries while the batteries is doing the work.

@sunnyicefire 3 года назад

How long did it take?

@AJRestoration 3 года назад

I had it in there for 24 hours if I remember correctly.

@rigobertcarolina4646 3 года назад

Why not Ac power instead of dc power. Is it posibel??

@AJRestoration 3 года назад

Ac Mains is extremely dangerous, it could kill you.

@nicholaspjames 2 года назад

AC at mains voltage is extremely dangerous. But also, it won’t work because the current alternates and therefore the workpiece is alternatively between cathode and anode. The workpiece needs to stay as the cathode so you need to use DC.

@adamyasingh3713 11 месяцев назад

Can I use 9V battery?

@AJRestoration 11 месяцев назад

Yes you can.

@Nightowl76 2 года назад

Pool acid is the best 👌

@timgannon2993 2 года назад

I got rust on my towbar but it is to hard to put back of car in that bucket

@AJRestoration 2 года назад

Sandblast it, and chrome or nickel plate it. Best option I'd say.

@jaimerodriguez4936 2 года назад

Amigo, pudiste usar vinagre durante 12 horas y te viera quedado muy bien.

@Thrashaero 3 года назад

Be careful not to use any chrome coated metals or stainless steel as these can release chromium-6 (highly toxic) in this process.

@AJRestoration 3 года назад

Yes

@madansharma2700 2 года назад

What happened to the other electrode.

@xeroxparc9260 2 года назад

abducted by aliens

@20yearsago88 2 года назад

I have no idea why I thought it was going to come outta the bucket chrome when he finished the process lmao

@Sqoou_Too 2 года назад

Because in the back of your mind you remember seeing an electrolysis plating video instead of removal. #Electroplating #ReverseThePolarity

@andiestwo5 2 года назад

Those vices are not crome, but are cast and come painted so it may have a slight shine, but best case it will be silvery gray.

@mjrawesome3430 Год назад

If the anode (can) touches the cathode (tool), won't that cause a short circuit and damage your charger/wires? If so, then this setup is not very safe.

@AJRestoration Год назад

It is the basic setup. Nothing can be idiot proof ;-)

@mjrawesome3430 Год назад

@@AJRestoration It just seemed to me that the anode/cathode are a little unsteady AND that they are in very close proximity of each other. Overall, I think that it's a nice, minimalist setup, but perhaps it would benefit from an additional tweak which would ensure that the anode/cathode don't make direct contact.