How to Replace a Harmonic Balancer on a 5.0 Ford Mustang

Подписаться 5 тыс.

Просмотров 10 тыс.

50% 1

Matthew walks you through the steps to replace the harmonic balancer on your Foxbody Mustang or other 5.0 Ford. The video includes a discussion of tools and techniques, why you want to replace the balancer, and all the pro-tips you need to make the job come out right.

Авто/Мото

Опубликовано:

6 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 41

@brucedye576 Год назад

I appreciate your time and content I'm learning from you I've had many foxes but never really learned how to maintain them so I appreciate your time

@tecmotiondyno Год назад

Thanks for watching!

@JamesSmith-nv3mb 3 месяца назад

I’ve been searching all over because I have this exact same car and issue. Awesome video!

@tecmotiondyno 3 месяца назад

I'm glad it is helping you out. The balancer on most of these cars is well past its prime unless it has already been replaced. There are lots of other related technical videos on the channel for you to check out too!

@yellow351mustang Год назад

Thank you so much for your videos. I have learned a lot about the Fox Body's from watching your channel. I just discovered your channel recently and have been trying to catch up on past videos. I have a bone stock 88 GT. While it is an 80,000 mile survivor and in mostly mint shape, it is still a 35 year old car. I had to replace the clutch fan a couple of months ago because it was all hair-lined cracked. I have heard horror stories of these flying apart. I have also recapped the EEC, which is the DA1 because the 88 is speed density. The caps hadn't started to leak yet. But you could see they were just starting to bulge. Dodged that bullet. After watching this video, you got me worried about the balancer as I'm sure it is stock and probably breaking apart as you pointed out. I will have to get after this before anything bad happens with that. Thank you again!

@tecmotiondyno Год назад

I had a car in the shop this spring with what was supposed to be a new Dorman replacement balancer and it was spun over 80 degrees. I could not move or wiggle it by hand either, but it had spun almost a quarter turn, so it really does happen. If you find the channel useful, please pass it around. Thanks for watching!

@mustang5214 7 месяцев назад

Same here

@motor_citymuscle288 9 месяцев назад

Great video! Thanks for making this video and sharing your knowledge

@tecmotiondyno 9 месяцев назад

Hope it has helped you out!

@motor_citymuscle288 9 месяцев назад

@@tecmotiondyno it will. I’m removing everything to upgrade the cam and timing chain on my 95 mustang gt 302.

@tecmotiondyno 9 месяцев назад

@motor_citymuscle288 There are all kinds of videos on here regarding a 302 engine build up which you might find helpful too. Thanks for watching!

@motor_citymuscle288 9 месяцев назад

@@tecmotiondyno I’m going through all of the videos! Very very helpful. I’m also doing AFR heads, FiTech carb style fuel injection and removing smog pump and A/C.

@geomaz35 Год назад

I just installed PowerBond 1084ss, it was the best choice for the money. Only issue was I had to chase threads for the pulley bolts on reinstall. Thankyou for the videos.

@tecmotiondyno Год назад

Quality is down all over but that’s the first I’ve heard of it with Powerbond. I did have a customer in the shop the other day with what was supposed to be a new Dorman balancer that was spun over 80 degrees, so it really does happen.

@ericlthornton571 8 месяцев назад

@geomaz35, what tools did you use to chase the threads in your pulley bolt holes on the pb1084ss? I've got to do the same to mine, too

@geomaz35 8 месяцев назад

@@ericlthornton571 A thread chaser tap, and new 3/8 bolts. Use compressed air nozzle to blow out any debris. The PB1084ss noticeably smoothed engine vibration. I now regularly test fit all bolts / threads while on the bench instead of halfway through the job under the car. Learned my lesson. Even brand new oil filters will have machining burrs in the threads.

@ericlthornton571 3 месяца назад

Well, I got a tool from harbor freight that took the original balancer off and installed the new one without a problem! But, it didn't fix the issue. After running the cylinder balance test and finding the #1 cylinder dead, I took the computer out and sent it to FoxResto, who fixed it, and sent it back to me. No issues whatsoever afterward. Runs and drives great!

@tacticalkitty5654 Месяц назад

Hey great video! But I’m having trouble getting the harmonic balancer back on. If I try to put the crank bolt back in and tighten it it doesn’t push in the balancer. Am I missing something?

@tecmotiondyno Месяц назад

I hope you didn’t strip the crank threads. You should use a longer bolt to get decent engagement on the crank threads like I did or better yet a balancer installer if you could find one that works with the 5.0 setup. If you have an automatic you should still be able to get it started but at some point you will just start turning the whole crankshaft so you may have to brace it with something. If I recall when I did this automatic I used a steel bar between a flat spot on the edge of the balancer and the shop floor with a microfiber in between to avoid marring the balancer.

@kaitlynrich5540 Год назад

Do you have to change the timing cover seal I have a older f150 needs a balancer. Got the basic one from rock auto. Not trying to put a lot of money in the truck this moment. Maybe In the future

@tecmotiondyno Год назад

If the seal is good and there were no leaks around the original balancer, you should be fine. If you do have to replace the seal, chances are you will have to pull the front cover because they are not easy to get out otherwise. I reused the seal on this one and after running the heck out of it on the dyno it looks fine. Make sure you put a little grease on the balancer on the seal surface when you install it.

@Mustang8846 2 месяца назад

@techmotiondyno. I have a stocked 1988 Ford Mustang LX 5.0. I am the only owner, so no modifications have been made to it. I hear that Ford made at least 3 harmonic balancers for the 302 and 351 engines. Can you tell me which one is needed for my vehicle? Thank you.

@tecmotiondyno 2 месяца назад

The 88 Mustang 5.0 uses a 50 oz imbalance, so that’s the balancer you need. I’m pretty sure that the Powerbond part number I used is either in the video or in the comments.

@Mustang8846 2 месяца назад

@@tecmotiondyno You don't mention the part number but at 17:49, you pan to the HB, but it is hard to make out the numbers on it.

@Guitarguy0522 3 месяца назад

Got tow questions I have to do this job what did you mean about the old shaft dropping into the pan ? And sec question how do I get the longer bolt to install the balancer before using the reg bolt I dident fully understand if you could please fully explain so I can get in proper and correct and do t screw anything up my car me and a lot to me and I don’t wanna pay someone to do this job when I know in an just do it my self so please help in anyway you can

@tecmotiondyno 3 месяца назад

There is a key on the crankshaft. It engages both the balancer and lower timing chain sprocket. It isn’t all that likely to fall out and into the pan, but if you orient the engine the way I show you, the keyway will be at the top of the crankshaft and this makes it even less likely that it will fall into the pan when you pull the balancer. I got a longer bolt at a professional fastener supply store - Bolt Supply House in Calgary. You won’t be able to get something like this at just any hardware store. McMaster Carr is a National mail order fastener house if you don’t live near a dedicated fastener supplier.

@Guitarguy0522 3 месяца назад

@@tecmotiondyno ok thank you so much for the info so bring it to tbc on compression stroke like you did and check the cap and rotor to make sure so the key way will by on too I get what your saying now and one question might sound stupid but does my 5.0 motor have reverse treads ???

@pabloo5.0 Год назад

Great video! Do I HAVE to set motor to tdc when replacing harmonic balancer?? Or can I just take the old one off and slide the new one on the key way

@tecmotiondyno Год назад

No, but it is a best practice and easy to do. As I pointed out, when you set it at TDC #1 compression the keyway will be at the top and there is a much reduced chance of losing the key in the pan, and if for some reason you end up loosening or pulling the distributor, you are at a good known reference point to put it back. Just use a ratchet to turn it to TDC just before pulling the bolt. It will take you an extra 20 seconds.

@pabloo5.0 Год назад

@@tecmotiondyno Ok thank you for your advice! I appreciate the help

@markweber7275 Год назад

Matt, which replacement balancer did you use? Thank you

@tecmotiondyno Год назад

Powerbond 1084SS. This is an SFI approved 50 oz balancer which costs around $250 Canadian. You could just use a cheap service replacement, but for a tiny bit more money you get a real quality part that will NEVER fail in an application like this.

@eddiefalcon8316 Год назад

Matt I have a good balancer that is working fine but 20 years old or so, have to do engine work due to timing chain issue. Is this something that I should just replace while I’m in there?

@DukeICT Год назад

You never stated sizes of the 4 bolts in the pulley and the size for big bolt. Also, what if the balancer has already spun apart. How do I find TDC?

@tecmotiondyno Год назад

You would normally just reuse the pulley bolts that you took off the car - they aren’t anything special if you do have to replace them. The longer balancer bolt is 5/8” by 2 1/4” fine thread. You can find TDC by pulling the #1 plug and using an inspection camera to watch for the piston to come up to the top. If your engine is still timed correctly you can also pull the distributor cap and turn the engine over until the rotor is just slightly past the location of the #1 terminal. Neither of these methods is super precise but should be good enough for the purposes of this installation.

@DessiLu14 10 месяцев назад

Did you have to remove the radiator? I see a lot of guys doing that . I feel its unesasarry

@tecmotiondyno 10 месяцев назад

No, you don’t have to remove the radiator on a Foxbody for this.

@motor_citymuscle288 8 месяцев назад

I can’t get my timing cover off 👹. I’ve removed all water pump bolts, water pump, harmonic balancer, 4 forward facing bolts, 4 ground facing (oil pan to cover) bolts. I’m using pry bars and the top is coming off but the bottom feels like there’s a bolt still attached but this is/ can’t be…

@motor_citymuscle288 8 месяцев назад

I may apply heat from a heat gun to see if that helps. The car only has 80,000 miles in it. 95 mustang gt 302

@tecmotiondyno 8 месяцев назад

There are dowels on the outside bottom corners and that cover has to slide straight forward until it clears them. Often is is held in place by the gasket and the pan and when you try to take it off it wants to pry upwards and bind against the dowels. If I had my guess, I would guess this was a factor in your problem.

@motor_citymuscle288 8 месяцев назад

@@tecmotiondyno interesting. Makes sense, since the top is coming loose but the bottom isn’t budging.