No video :(

How To Replace A Volvo Oil Filter Housing & PCV - Volvo P1 Platform - Volvo S40, V50, C30, & C70

Подписаться 346 тыс.

Просмотров 123 тыс.

50% 1

►The PCV system is an integral part of any engine's performance and longevity. On the Volvo C30 and many others, the PCV system is built into the oil filter housing, and when it fails, it causes the crankcase vacuum to over pressurize. This can cause the engine seals to fail, resulting in loss of oil, oil pressure, and ultimately damaging the internals of the engine.
When the PCV systems fails, you will hear a whistling noise, see oil leaking from the camshaft seals, and notice that there is unusual suction on the oil fill cap. If you are experiencing any of these symptoms, it is imperative that you replace the oil filter housing before any serious damage occurs.
Nate Vincent is back, this time in the shop, with another DIY showing you how to install a new PCV valve and oil filter housing in his own 2009 Volvo C30.
Read more on our blog: blog.fcpeuro.c...
Shop Parts Kit Here: www.fcpeuro.co...
Shop Oil Change Kit Here: www.fcpeuro.co...
Shop CTA 1100 Here: www.fcpeuro.co...
This Kit Fits the Following:
Volvo S40
2004 Volvo S40 i 2.4L L5 PCV Valve Oil Trap Kit
2004 Volvo S40 T5 2.5L L5 PCV Valve Oil Trap Kit
2005 Volvo S40 PCV Valve Oil Trap Kit
2006 Volvo S40 PCV Valve Oil Trap Kit
2007 Volvo S40 PCV Valve Oil Trap Kit
2008 Volvo S40 PCV Valve Oil Trap Kit
2009 Volvo S40 PCV Valve Oil Trap Kit
2010 Volvo S40 PCV Valve Oil Trap Kit
2011 Volvo S40 PCV Valve Oil Trap Kit
Volvo V50
2005 Volvo V50 PCV Valve Oil Trap Kit
2006 Volvo V50 PCV Valve Oil Trap Kit
2007 Volvo V50 PCV Valve Oil Trap Kit
2008 Volvo V50 PCV Valve Oil Trap Kit
2009 Volvo V50 PCV Valve Oil Trap Kit
2010 Volvo V50 PCV Valve Oil Trap Kit
2011 Volvo V50 PCV Valve Oil Trap Kit
Volvo C70
2006 Volvo C70 PCV Valve Oil Trap Kit
2007 Volvo C70 PCV Valve Oil Trap Kit
2008 Volvo C70 PCV Valve Oil Trap Kit
2009 Volvo C70 PCV Valve Oil Trap Kit
2010 Volvo C70 PCV Valve Oil Trap Kit
2011 Volvo C70 PCV Valve Oil Trap Kit
2012 Volvo C70 PCV Valve Oil Trap Kit
2013 Volvo C70 PCV Valve Oil Trap Kit
Volvo C30
2008 Volvo C30 PCV Valve Oil Trap Kit
2009 Volvo C30 PCV Valve Oil Trap Kit
2010 Volvo C30 PCV Valve Oil Trap Kit
2011 Volvo C30 PCV Valve Oil Trap Kit
2012 Volvo C30 PCV Valve Oil Trap Kit
2013 Volvo C30 PCV Valve Oil Trap Kit
Volvo S60
2012 Volvo S60 T5 PCV Valve Oil Trap Kit
2013 Volvo S60 T5 PCV Valve Oil Trap Kit
2014 Volvo S60 T5 PCV Valve Oil Trap Kit
2015 Volvo S60 2.5L L5 PCV Valve Oil Trap Kit
2016 Volvo S60 2.5L L5 PCV Valve Oil Trap Kit
Volvo V60
2015 Volvo V60 2.5L L5 PCV Valve Oil Trap Kit
Volvo XC60
2015 Volvo XC60 2.5L L5 PCV Valve Oil Trap Kit
2016 Volvo XC60 2.5L L5 PCV Valve Oil Trap Kit
Volvo V60 Cross Country
2015 Volvo V60 Cross Country PCV Valve Oil Trap Kit
2016 Volvo V60 Cross Country PCV Valve Oil Trap Kit
Volvo XC70
2016 Volvo XC70 2.5L L5 PCV Valve Oil Trap Kit
SUBSCRIBE: hubs.ly/H0cDnfN0
Get free parts from FCP Euro:
www.fcpeuro.co...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 218

@NicolasCageIsActuallyARobot 4 года назад

16:40: After installing each bolt, always give your car part a kiss. *That's* what I've been missing this whole time. Thanks, FCPEuro!

@fcpeuro 4 года назад

Of course! You're welcome! 🤣🤣🤣😂

@MrEspek 7 месяцев назад

Is that the only one video which shows how to replace Oil Filter Housing in older Volvos? Was looking for that for few days. THANK YOU VERY MUCH!

@daviddennett2645 3 года назад

I've done hundreds of these, was a Volvo technician for about 16 years

@interactive1178 2 года назад

How long does the repair usually last? I had one done a year ago on my 2012 c30 166,000 and now it looks like I have to get another one replaced.

@daviddennett2645 2 года назад

@@interactive1178 took me about an hour max, if I remember correctly the turbo engines were easier to do than non turbo. Non turbo bout an hour all in, turbo engines like 40 to 45 min. A lot of cleaning the oil that leaks out too

@interactive1178 2 года назад

@@daviddennett2645 is it common to get one every year if you put a lot of miles on it?

@daviddennett2645 2 года назад

@@interactive1178 with the way things are built so cheaply I wouldn't be surprised. How many miles you do a year?

@daviddennett2645 2 года назад

If you're over 200k by now I would expect another one is needed yes. Remember this is a FoMoCo engine, which means it's made by Ford. Worst thing Volvo did was to sell to Ford. Ruined quality

@toddhoodenpyle6989 2 года назад

Strong work, Nate. I started getting the dreaded "Alien Spaceship" whistle/whirl the other day. Super helpful, I get to do this on the P3 S60 tomorrow. Your attention to the small details took the scariness out of the project!

@fcpeuro 2 года назад

Rock on!

@rickw2777 3 года назад

Thank you so much for putting this video together! I followed you step by step taking it apart and putting it back together! Your instructions were very clear and accurate. You saved me over $600! Thank you so much!!

@LuisLopez-zt2ib 2 года назад

Ditto on my S-40. Made this job more simple w/your instructions.

@keatonkottick5992 2 месяца назад

Just did this DIY, overall this video is a great step-by-step guide! outta 10 I'd say its about a 6-7 outta 10 on how difficult it is to perform this DIY. The hardest part was removing the airbox and re-installing it the bottom plastic mount was getting caught on the water pump i ended up shaving a very small amount off with a file to make a little bit more clearance during the installation. I ended up using a tap to create new threads for the bolts on the new housing. I also didn't have a long 10mm wrench on a flex head ratching for the housing bolts so that slowed down the process slightly. I would also recommend oiling the new housing gaskets with some oil to create a guaranteed seal "oil acts as a sealant" but overall an easy job with the help of this video! I had a check engine light on for Bank 1 running lean and the terrible noise as shown in the video. All fixed now!

@garyganoe2786 3 года назад

Easy Job referring to this video as you remove and install the housing. Tells you which bolt goes where and size. Very detailed. Great video.

@fcpeuro 3 года назад

Glad it helped!

@JRizzo-li2dr Год назад

Just did this job on my 2015 V60. Video was very helpful, the whole job was pretty smooth and easy overall!

@MrRightNow Год назад

Good video, i did the repair earlier today and I would add that you don't really have to take the ECU out the air box and you don't have to go under the car to remove the 3 bottom bolts, they're easily removable from the top. I did the whole repair on a parking lot and didn't have to get my jack out to lift the car at all. Also, i would highly recommend removing the coolant reservoir hose before taking out the air box, because it is very easy to damage that plastic hose which is a bit in the way

@fcpeuro Год назад

Thanks for sharing!

@justinjayankura8676 3 года назад

Thank you for this video. I had this problem last week. I went to a Volvo specialist and got it replaced, it costed me $700 with parts, labor and oil change.

@interactive1178 2 года назад

How long does the repair usually last? I got one replaced on my 2012 c30 a year ago and now it looks like I need another one replaced.

@daviddennett2645 2 года назад

If I recall it was like 4 to 450 with oil change n labor. 500 max at my uncles shop, the part isn't cheap either

@fcpeuro 4 года назад

Step by step process starts at : @3:51 Buy the Replacement Kit Here : www.fcpeuro.com/products/volvo-pcv-breather-system-kit-c30-c70-s40-v50-l5pcvkit?

@7spower998 3 года назад

Nate, there's a big difference between a PCV and a CBV, or a CRV. Most domestic and some Asian cars use PCV. All European and some Asian cars use CBV - Crankcase Breather/Regulating Valve, but not PCV. The two functionally identical but different in design. Volvo doesn't use a PCV but a CBV.

@7spower998 3 года назад

25:02 Our next step is to prefill the OFH with oil to prevent dry start-up to the valvetrain, or you had done that already?

@farasmaroge1465 Год назад

Very thankful for the ppl at fcp euro. I could never do this without these experts. I would have easily been overcharged by the volvo dealer(~$700)!

@georgewashington1106 2 года назад

Hey, awesome video. I especially like how you just glossed right over the hardest part...pulling that stupid air box. I've been yanking on mine for half an hour. I'm ready to take it out with a sawzall and put it back with duct tape. - If you're doing this, the tab on the back of the airbox catches on the intake. Pull the passenger side of the airbox toward the front of the car while pushing the entire airbox to the driver side

@fcpeuro 2 года назад

Sorry that was glossed over George, noted for the team.

@mateuszkaminski4174 Год назад

To make that easier you can lift up the engine ( engine mount from passenger side should be unscrewed).

@schoonergee5741 3 месяца назад

Took me less than a minute following the clear instructions. Taking the lower fasting screws of the ECU was more of a mission. Note: it's actually not essential to remove the ECU from the air box or remove the air box completely to replace the PCV Oil Filter Housing. Just ease the air box mounts from the rubber grommets and move the air box a few inches to the right will give you access to the mounting bolts.

@brentdarrin1109 2 года назад

This was very helpful even for the S 60

@erryhiller1014 4 года назад

I have a 2010 S40 T5. Ive removed the air intake "horn" above the left side of the radiator, along w the descending intake hose, to replace both with a cold air intake/filter. In fact, the CPU is also repositioned to a bracket to the left of the original air box/filter location. As a side benefit, I can directly & easily access my oil filter for changing AND PVC breather behind it. Replacing the breather diaphragm is extremely easy. The cap can b pried up & off & a replacement diaphragm, which IPD sells for about $9, ("item 140065 - Oil Filter Separator Box Diaphragm - 5 Cyl", albeit not a Volvo OEM...but much of what IPD & FCP sell is not OEM) be swapped in without the extra work of removing engine parts to create access. The "remove-the-intake-horn-&-down hose + cpu" will give enuf access to the breather cap to allow the swap...& save 20 min work & the cost of replacing the entire oil filter-breather housing, oil feed tubes & all ($260+)..vs $8. Less time, less effort & less expense. It seems this is a better way, especially for the DIY home wrench jockey.

@fcpeuro 4 года назад

That is true! An aftermarket intake and CPU relocation does make it much easier! Plus you get more turbo noises!

@erryhiller1014 4 года назад

@@fcpeuro especially if u replace stock one-piece turbo+manifold w 2 piece Garrett (w higher boost) & billet milled manifold w grade 8 bolts. Noise in cabin is magnificent. Gonna add 2nd Pierson blow-off valve in parallel to existing, w braided line to get more mellow sound & rapid pressure release to reduce back-pressure wear...not simply @ stop lights but also in speed-gear reduction. Ultimate machine wud hav Audi TT RS 3.2 NA or current run since S40 is a sleeved engine. Mounts tho r problematic since Volvo 2.5 engine is top mounted on passenger side & bottom (torque) mounted on driver's.

@lewisnorthofthewall Год назад

I swapped the diaphragm(which was totally fine)!! The lid has a lip under it which I didn't realise so was prying up the whole thing up and have cracked the housing as oil now leaks slightly out of the cap!!

@chadriddle3517 9 месяцев назад

What is the website where to order just the diaphragm? I need one myself

@bv3078 Год назад

I acctually clean used pcv housings and replace the rubber parts in them. Rebuilding the pcv saves a lot of $$$ and is very easy.

@tyronehill8752 6 месяцев назад

About to try this method on my 3008 V50. 👀 to clean the PVC valve and replace the diaphragm. Wish me luck.

@r.zabawa5670 3 года назад

One thing that I think you forgot or could have done. Is verify the fix with the stuck pcv valve. Take the oil cap on and off like" a" before and after"... So us n00bs can get a good comparison. Great Job ...

@JeffreySuddard 5 месяцев назад

So helpful thanks

@Latingear 2 года назад

Debating if it's worth spending $700 for the fix or DIY. Not experienced in being a mechanic but definitely not afraid to try it with this video as a reference

@fcpeuro 2 года назад

We have full faith in you, Dennis!

@tirgod100 3 года назад

omg.. he is disassambing the whole car :D :D

@jaggybob1 3 года назад

Omg, I gotta do that same job myself now. Son of a b....

@grodt88 3 года назад

@@jaggybob1 just replace that: 30788494 rubber and you will be fine

@ZCarReviews 3 месяца назад

Thank you for the video. Helped a lot with my 2007 Volvo S40 T5 AWD

@snajjpern 2 года назад

Simpler and much cheaper to only replace the diaphram!

@MK2CLIOOWNERSUK Год назад

what an AMAZING VIDEO

@as400guy34 2 года назад

What is the estimated installation time for an experienced Volvo mechanic 2010 S40 T5 R-design ? I was advised 3.5hrs at $137.50 per hr part $214.99 total cost $696 sounds about right based on what others commented in this feed.

@philipwu9907 3 года назад

Thanks for the video. Quick questions, I did the glove test on the engine oil fill hole and my glove is sucked in during idle. Will changing the pcv housing fix this or is this another issue?

@fcpeuro 3 года назад

Actually that means your PCV system is functioning perfectly! When the PCV system fails it will blow the glove up rather than suck it in.

@stevenn8113 4 года назад

You make it look easy😂

@raymondtuckerjr1886 4 года назад

Lol, someone ELSE always does!

@rileymsdad 3 года назад

You guys make such great detailed vids! Very helpful

@lifetech9575 Год назад

Awesome advisory in video as usual!!

@jellybean1976928 4 года назад

Needing to do this job as of now, seems like it should be possible with air box in place? Yes, would be tight, but sure a lot less stuffing around. Plus, is dumping the engine oil required? The sump level being well below the filter housing I don't see why you'd need to do an oil change, unless of course it was due. Mine was done just 200KLM ago, so even though I change it often that'd be ridiculous. My daughter has driven the car a few days like this and hope she hasn't rooted the seals.

@fcpeuro 4 года назад

Removing the air box will certainly give you more room to work with. It will be a messy job if you don't drain the oil beforehand. If you really want to, you can reuse the oil you drained out so long as the pan you drained it in is clean.

@jellybean1976928 4 года назад

@@fcpeuro Yes, just did the Job and the air filter box really needs to shift out of the way. This job isn't particularly fun, but it's a nice feeling when it's done. I left the MAF and computer attached to the filter box and managed to just gently lift it off to the side without fully removing. I'm always after any steps that can be eliminated and still get the end result. On another note, the air filter box pulled out allows access to the radiator hose and thermostat assembly, so if your car is aged and has done mileage it's a no brainer to get those parts at the same time. Mine only has 100K KLMS so hopefully I don't regret not changing these out till the next time I have a reason to go through getting into this space again.

@schoonergee5741 3 месяца назад

Great tutorial...

@fcpeuro 2 месяца назад

Thank you! Cheers!

@walterstiglich2358 2 года назад

Es INCREIBLE como los del video COMPLICARON TODO... La valvula tiene una tapa en el porta filtro quese gira y se abre se cambia y se cierra NO ES NECESARIO DESARMAR TODO

@mattbanagan Год назад

Don't forget these engines are in the V70 P3 too!

@eeeckstrom 4 месяца назад

Other than that, great video. Thanks

@lcmijango 3 года назад

Cant thank you enough for this video. Thank you.

@abnormal700 3 года назад

Going to do mine today. Great video . Thanks

@betoestrada3248 3 года назад

New to the volvo family and new subscriber great video btw

@fcpeuro 3 года назад

Thanks for the sub!

@namlo8765 3 года назад

As I was watching this video. That’s night my 2016 Volvo XC90 PCV oil trap when out.

@TassyDeval Месяц назад

Just out of curiosity. If it is only the diaphragm that is shot, why not just replace that? Also, if you are a long way from home and this happens, can you loosen oil filler cap, to release a bit of vacuum in motor to prolong the bearing seals destruction?

@uusa35 2 года назад

thank you so much for such valuable video

@fcpeuro 2 года назад

You are most welcome!

@dtmfool789 3 года назад

I just did the diaphragm replacement instead of the entire housing. I’m still getting excessive vacuum. Any idea what else causes this?

@thuddiz 2 года назад

did you get it fixed? I changed the whole housing and still have excessive vacuum...

@gregb.5796 Год назад

@@thuddiz how’d it turn out? What was the remedy?

@thuddiz Год назад

@@gregb.5796 Still to this day I havent figured it out, still got an engine light on and i can hear the air being sucked in the enginespace. I have given up 🫠 car runs like shit when i press the gas a little to much and the fuel milege is really bad because of some leak but other that that it runs good

@chadriddle3517 9 месяцев назад

Where did you purchase the diaphragm ?

@chadriddle3517 9 месяцев назад

Could you have a vacuum leak somewhere else ?

@Pelinas Год назад

Very informative, thanks

@fcpeuro Год назад

Thank you for viewing!

@HERBYWALLACE3 3 года назад

Fcpeuro is the best!

@fcpeuro 3 года назад

YOU'RE the best Herby!

@HERBYWALLACE3 3 года назад

@@fcpeuro have a question I have a 2016 Volvo xc70 with same engine, when you disconnect the battery and the ecm, do you have to reprogram everything. Let me know thanks Herby

@user-fv4mv2ch1m 3 года назад

i just got a new breather box but no tubes... is it super necessary to replace the tubes?

@georgefoukal22 3 года назад

is this job an hour or more what should we expect for cost in Canada BC...great video I hope my mechanic is as thorough and careful as you are.

@fcpeuro 3 года назад

For a labor cost from a shop you'll want to get an estimate locally as they'll all have different labor rates and the book time they use might vary.

@rafterkim1 3 года назад

Fcp is the rule!

@homeytube1 3 года назад

OMG. I'm 1/3 of the way through the video.......I think I'm gonna sell it!!

@homeytube1 3 года назад

17:01.....omg

@homeytube1 3 года назад

20:48 "THE TIME HAS COME".....oh thank god!

@blakeolinger1220 4 месяца назад

Can you temporarily plug the tube and put a filter on the valve cover to vent the crank case? I need to drive the car until I fix it

@Volksoner619 Год назад

Can I come live in your shop? If no, I’ll settle for a job.

@juliap5092 3 года назад

They asked me for $700 to replace it, is it adequate? Volvo S60 2012

@amboytex Год назад

Same here, made my DIY easier, thank you, but I hit a snag... 1 of the 2 MAF T25 Torx screws broke while I was reinstalling the MAF. 🤬 Do you have the part # for that screw?

@martincastillo3574 3 года назад

Very good video

@fcpeuro 3 года назад

Thanks so much Martin

@user-zl4yg9ym6f Месяц назад

Is this the same for a 2.4i (non-turbo)? I have a 2008 S40 2.4i and my engine compartment looks different, with the five "finger-like" intake manifold on top. Does that intake manifold need to be removed on this engine as well in order to replace the oil filter housing and PCV?

@eeeckstrom 4 месяца назад

I think you could've shown how the clips on the belly pan are used

@LaRafa7 4 года назад

When will you make a video for the P3. You guys rarely show P3s any love on here. Appreciate the video though.

@fcpeuro 4 года назад

We plan on doing a P3 video!

@user-uv6ze2mj2f 9 месяцев назад

Hi, just want to verify if the C70 volve radio system requested a code when you re-connected?

@richardbennett887 Год назад

Got a 2015 v60 with 2.5 5 Cylinder am I going to Expect this

@02S40Volvo 28 дней назад

I need a video on how to do this for a Volvo s40 2002 1.9lt

@richieDanza85 Год назад

When the timing belt, pistons and valves are replaced, does the oil filter housing get removed too?

@gregb.5796 Год назад

Did I miss the reinstall of the self tapping bolts? Do they go back in after it’s mounted back to the block?

@sramy123 4 года назад

First step: try replace Breather Volvo oem 8642424

@winnington23 8 месяцев назад

So much easier than on my S70 T5 lol

@fcpeuro 8 месяцев назад

😅

@lew381 2 года назад

My s40 1.8 2008 has an oil leak but i realised rhe person overfilled the oil! it doesnt make any noise. It did blow air rather than make a suction force? Is this also a sign i need to replace the pcv? Many thanks.

@amana1480 3 года назад

Don't forget to put the zip ties back (unlike the mechanic who worked on my car, and left loads of wires loose)

@glindenb Год назад

This seems to be a pretty big undertaking. So while in the neighborhood is there anything else that should be checked/maintained/replaced?

@farasmaroge1465 Год назад

No but I did my transmission oil drain and fill since the hole for the fill freed up a little on my model after the airbox was moved.

@joseduranjr4963 2 года назад

Can you please do a video Ann how to clean the throttle body on a 2017 VOLVO XC60 T6 with the 2.0 supercharged/turbocharged engine? PS-I cannot locate the PCV valve either. Does this engine even have one?

@DigitalSplice 2 года назад

I don't have the sound but my housing is covered in oil. I'm going to assume it's time to replace it?

@zoohed 3 года назад

Hi just purchased PCV from you but it seems my 2002 S40 has an extra U hose on left of PCV box . This hose slips onto end of Exhaust manifold. do I plug it up or leave it open?

@kamata93 3 года назад

That ECM module seems to be in the stupidest location ever. I mean, just look at all the dirt it has. No wonder people complain after having a car wash or something. Other than that, thank you for the video. I am considering V20 2.4i for purchase soon.

@fcpeuro 3 года назад

definitely a good point!

@BrattyVicky 2 года назад

Well, I just did this, had 3 bolts leftover! Fingers crossed it wasn't for anything important xD

@fcpeuro 2 года назад

Spare parts! 😂

@KYRGarage 3 года назад

does the oil change kits on the fcp euro site for the 2.5 also work for the 2.4l? like the oilll filter and such

@JimmyDean404 2 месяца назад

how come not a ton of info and parts on the new gen?

@digb1 4 года назад

Hi. Would this apply to a 2007 C70 D5? Pretty new to these platforms so help appreciated!

@juliusmarshall2950 3 года назад

I am looking for how to replace crankcase breather hose on 2009 volvo c70 t5

@raedrg4593 3 года назад

Hi I hav d5 s40 and I have some smoke going out from the oil cap I do clean the pcv All but I still have smoke and the glavs blows up, soo how Kan I test the pcv in another way if u know please? . Thanks

@schoonergee5741 3 месяца назад

At Volvo dealers in NZ you'd be paying NZ$1200 just for the parts plus six hours labour at $100/hour. An absolute ripoff not helped by Volvo /Ford sticking the PCV Filter housing in an almost inaccessible location. Grrrrr

@gamechangerz1329 7 месяцев назад

do you have any videos for 2.4i engine ??

@tanjaiwei4710 Год назад

Hi May I know what caused if the oil filter house cap keep flipping up?

@SaiKumar-ir4xc 4 года назад

Would FCP EURO ever go to extend the business to Japanese vehicles? I know EURO stands for European, maybe something else for Japan?

@matthewkuhl79 4 года назад

FCP NIPPON!

@amosdodson4022 2 года назад

Also goes for S60 T5 2012

@fcpeuro 2 года назад

Thank you, Amos!

@ryd137 4 года назад

when accelerating from a stop i got a tiny shake / vibration when moving any thoughts thank you c30 2008 t5 volvo

@fcpeuro 4 года назад

Shaking/vibration when accelerating from a stop could be a number of things. You could have worn engine mounts, or cv shafts, or it would be a slight misfire, or a number of other things. A tiny shake doesn't sound too severe, but it might be a good idea to get it check out at a shop!

@user-qr3lh3du1e 2 года назад

Hey I just want know how to dismantle this freaking pump from its hose I ask if you do a video about it it's a double pump on volvo s60 2008

@klpwpk8790 2 года назад

I have a 2010 S40 T5 . It it smoking (oil burning ) at idle and burns oil pretty bad. Would the PCV system be the problem or is it something else. Car has just over 100K on it.

@fcpeuro 2 года назад

Hi Will, a good start would be to check the system, and then consider further diagnostics should the PCV system be in proper working order.

@sd3417 2 года назад

Easy peasy

@richardparis8738 Год назад

Full dipstick out too

@erbalumkan369 3 года назад

is it possible to install a pre-krank electric oil pump on these?

@stephenstrader1577 4 года назад

If I suspect this problem is going on on my 10’ V50 2.4i, (CEL on and immediate audible clicking at idle), can just the faulty diaphragm or the PCV (assembly) be removed and replaced instead of having to replace the entire oil filter housing? Thanks for your advice in advance.

@stephenmorrissey1254 4 года назад

You can just replace the diaphragm. The cap pops off using a screwdriver and the new one drops in. The 2.4i is a lot easier to access and shouldn't need anything removed other than the cap.

@chadriddle3517 9 месяцев назад

Where can you purchase the diaphragm

@lew381 2 года назад

Hi would this be similar to s40 2008 1.8 (duratec engine) many thanks

@MutengweTshilani 8 месяцев назад

How do you reset the engine check light after replacing the PVC?

@hammervonjammer1279 2 месяца назад

Likely need a scan tool (aka code reader) to erase.

@eatmemane Год назад

Do i have to drain my oil while doing this or can i change out just the filter. Reason being is my drain plug is stuck

@fcpeuro Год назад

Hi LuckiCub, it is recommended to do an oil change when you do this job, you may also be able to use an oil extractor for that.

@alibabs153 3 года назад

There's nothing easy about this lol

@raulmolina91 4 года назад

Should there be vacuum at iddle on the line conecting to the turbo intake? Thank you

@fcpeuro 4 года назад

Yes.

@husarzpospolity 3 года назад

Is this oil filter housing contain anti drain valve?

@MrSiderShoot 3 года назад

Do you need to drain the oil to change this part? Because mine had a oil change not long ago and the part just failed

@alexanderstevens145 3 года назад

Just do it and put the same oil back in afterwards obviously use a clean container . I think if you don’t oil spills everywhere

@RayMainBagpiper 4 года назад

I'm wondering. My 09 C30 has always had what I call a 5 cylinder wobble, could that be an indication ? I'm averaging about 27 mpg after changing out the sparkplugs and coils. Normally running at around 75 / 80 mph.

@fcpeuro 4 года назад

Hi, Ray! Indication of what, exactly? These 5 cylinders definitely have a unique sound and feel. 27 mpg sounds just about right for these cars!

@RayMainBagpiper 4 года назад

@@fcpeuro I'm still figuring out what's normal with mine. I've replaced the coils and plugs and still it has a slight intermittant misfire. I'm getting ready to do the pcv diaphragm next. Thanks for the reply !!!

@emayteetee73 2 года назад

Ray, have you got used to the wobble yet? I know what you mean. When I’ve read up about it, it’s been referred to as ‘shimmer’ that you can hear/feel at low rpm. It’s simply the imperfectly balanced nature of a 5-cyl engine coupled with the firing order which accounts for this. If you search for videos on the matter, it’ll deepen your understanding of it.

@seanm9940 4 года назад

I just changed the oil filter housing, and I now have low oil pressure and CEL. Any suggestions?

@fcpeuro 4 года назад

I would first check the obvious, your oil level. Then, its possible you have a fault in the oil pressure sensor. Otherwise, you may have some engine problems, such as a failed oil pickup tube seal or even a bad oil pump.

@seanm9940 4 года назад

It was the oil pressure sensor. Thanks for such a quick response. I am a new customer, and my experience with FCP Euro has been great! Really appreciate the videos and support y’all offer.

@koden24 Год назад

Man, I can’t understand how these parts go bad like this. I only have 77000 miles on this c70. What causes this part to go bad this fast.

@hammervonjammer1279 2 месяца назад

Right??? Mine failed at 58K. Bad design, worse manufacturing.

@Macgyvertulsa 7 месяцев назад

23:10 when he is putting the 90° elbow hose in, is there any treat to getting it on? I have tried for about half and hour and cant seem to get the hose to slide onto both ends.

@fcpeuro 7 месяцев назад

It is a very tight squeeze, bending the hose almost in half to get it on.

@Macgyvertulsa 7 месяцев назад

@fcpeuro I got it on this morning. I realized that it had been in my cold garage and it wasn't very flexible. I warmed it up a bit and when on in about 30 seconds.