How To Replace & Calibrate Honda TPS (throttle position sensor) - Code 7 Check Engine Light

Подписаться 93 тыс.

Просмотров 559 тыс.

50% 1

TPS Sensor I'm using - amzn.to/2JJM4qm
Inexpensive Multimeter - amzn.to/2JIHKaN
Pretty simple walk through on how to test and properly adjust the TPS. This will work on many Honda and Acura engines from the D, B, and H series engines. I adjusted this in my 1990 Honda Civic EF hatchback with a b20b engine swap and a 90-93 Acura Integra intake manifold and throttle body.
If you are getting a code 7 on your ECU, this relates to a problem with the TPS.
Help Support my channel, purchase decals here - garagebuilthondas.bigcartel.com
Send me stuff here!
Jon Widmer
PO Box 13594
El Paso, TX 79913
/ garagebuilthondas
Thanks for watching!
Disclaimer
"Due to factors beyond the control of Garage Built Hondas, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Built Hondas assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair videos. Due to factors beyond the control of Garage Built Hondas, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again, any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Built Hondas."
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll potentially receive a small commission at no cost to you. This will help support the channel and allows us to continue to make videos like this. Thank you for the support!

Авто/Мото

Опубликовано:

1 авг 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 460

@powereng1000 5 лет назад

PLEASE DELETE THIS VIDEO.... you will never adjust or touch the TPS sensor. Japanese engineers have this set DUMMY! That's why those bolts are not screwable.

@GarageBuiltHondas 5 лет назад

Haha. And when you replace it? Hello?

@powereng1000 5 лет назад

@@GarageBuiltHondas you should replace the entire throttle body, which comes with manf tuned settings...

@GarageBuiltHondas 5 лет назад

No. That's not required otherwise they wouldn't sell independent TPS's. That really wouldn't be cost effective. Think of all the Honda's in the world with aftermarket throttle bodies with not a single TPS already attached. Do you really think they have a hard time adjusting those? This method works perfectly fine.

@powereng1000 5 лет назад

@@GarageBuiltHondas yes with tuning issues...

@GarageBuiltHondas 5 лет назад

Lmao, wow. Just stop man. It's like you're arguing that water isn't wet. Geez.

@spiderboi9070 3 года назад

Watch your videos a lot now that I own a 88 civic hatch , and 4 years later this helps so many people including me

@FroztiProductions 2 года назад

Tip for anyone adjusting their throttle to make it as smooth as possible. Do not adjust wide open throttle voltage. Yes it's supposed to be 4.5v but if you get this perfect your closed throttle voltage will be off and your throttle will be jerky. Get closed throttle to a perfect .5v and you're done. When you're wide open throttle the ecu is using the map sensor anyway so there's no point in getting it perfect and messing up closed voltage. That tool you made is awesome, I'm going to make a cleaner version as I adjust TPS frequently.

@GarageBuiltHondas 2 года назад

Good tip, thanks for adding the comment!

@ricerfoo5805 Год назад

Bro, a buddy of mine calibrated mines while open throttle and its super jerky, gonna give this a try right now

@FroztiProductions Год назад

@Ricer Yoo do it and let me know. Take your time with it, takes me a lot of tries cuz every time I tighten the bolts the reading changes.

@Manute951 Год назад

Thanks, yours seems like a good advise. Does this applies to every fuel injection systems? I have a Honda cb1300, calibrated my TPS to the full throttle, and idle is about 0.7 volt. Throttle is a bit jerky at low rpm, maybe your are right about tuning at closed throttle.Should try it.

@FroztiProductions Год назад

@Manute951 Any system with a cable throttle and TPS I believe should benefit from this method.

@Deathphone 4 года назад

I made the mistake of adjusting my cable thinking it would help before addressing the IAC sensor. Thank goodness for you and this vid my dude

@GarageBuiltHondas 4 года назад

You got it!

@nahid1981 3 года назад

I was looking for this video recently, and here it is...thanks a lot man. Really appreciate it...

@GarageBuiltHondas 3 года назад

You're welcome

@zdreamer86 3 года назад

Great video! This worked perfectly. My Prelude had a blinking D4 light after I installed a new TPS and this fixed it. Thanks for the help!

@GarageBuiltHondas 3 года назад

Glad to help!

@MUGENKINGU 8 лет назад

Very informative video! Love how in depth you go.

@GarageBuiltHondas 8 лет назад

Thanks Goldman!

@darrellroireau4061 5 лет назад

Very nice you helped me perfectly! I watched several vids but yours helped me where I needed. Thanks Bro!

@GarageBuiltHondas 5 лет назад

Awesome! Thanks for commenting!

@darrellroireau4061 5 лет назад

@@GarageBuiltHondas yeah I couldn't get 4.5 volts open and was worried until I saw yours which was similar. Just a little off. My cars issue has been fixed thank god! Shes running smooth and powerful now! :)

@johnw1747 7 лет назад

john my man coming through again making another great video. just so happens i needed to learn how to do this. Thanks for all you do for the honda community.

@GarageBuiltHondas 7 лет назад

Anytime buddy, glad to help!

@inhaletimetimeinhale2519 5 лет назад

ER DERRRRR

@Busydadgarage717 2 года назад

Can't believe it has been 5 years since you had the old track car setup! Does not seem possible!

@GarageBuiltHondas 2 года назад

Right...

@RobertMorodan 2 года назад

Great video! 👍🏻 i have taken out my throttle body to clean it, i have replaced the gasket and after putting everything back i get this code 7. I haven't touched the tps at all... thank a lot ps, the car is a 92 prelude f20a4 engine.

@ArgentinianSkull 2 года назад

Just. AWESOME. any time I have an issue with my 91 EF, I come to your channel and you help me get thru it. Thank you for putting these videos up for the old school honda community! Congrats on the new garage and all the RU-vid success, do you take any of the D series toys out to the track? If there's a video of that i haven't seen it. I'm slowly prepping my ef for autocross. I have the original d15b2 with an mpfi conversion, 1999 d16y5 intake manifold, I also have the d16y5 at home waiting for the old d15 to throw in the towel. Thank you again for all the content!

@GarageBuiltHondas 2 года назад

Much appreciated, glad to always help! You've missed out, I raced a sohc supercharged d16 this last year for a few events. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hafkgoqUJI0.html

@vitreousphantasm Месяц назад

Super helpful video!

@GarageBuiltHondas Месяц назад

Glad it was helpful!

@carchk2054 4 года назад

Hi thanks for the video. I have a 02 Acura tl type s with the main and sub throttles. I did a cleaning of both and removed the tps on the sub throttle, not knowing what it was, to clean. Once i saw it was not something I needed to clean i screwed it back on. I then got a 94-1 and vsa and traction control light with high idle. I also got a p0505 code, which was corrected with replacing the iacv. The acura dealership states i still have the tsc light on which they said can only be the valve or a short. Im pretty certain its not a short or problem with the wiring as i did the work myself. Could it be that i need to adjust it as you do in the video. My autel scanner has the sub throttle idling very high with the live data. Any help would be appreciated. Thanks

@M1K3YTFL 7 лет назад

This was really helpful, thanks!

@GarageBuiltHondas 7 лет назад

You're welcome!

@mr.nobody4900 4 года назад

A +, Outstanding tutorial.

@GarageBuiltHondas 4 года назад

Thanks!

@ItsCX 2 года назад

For the plug you made with the alligator clips, where did you plug the other end to and what is it called? Sorry, I’m a little slow.

@chaoticflame5431 6 лет назад

Great video, thank you very much for your input.

@GarageBuiltHondas 6 лет назад

You're welcome

@marley91crxsi82 4 года назад

Dud this helped me alot thanx for the awso.e content

@GarageBuiltHondas 4 года назад

You're welcome

@ronniecason9807 4 года назад

Jon i just put a skunk2 alpha 70mm tb and a skunk2 pro intake on my b20b swapped crx after taking the tps and putting it on the new tb no matter how a turn the tps it wont go above .15v closed and 3.28 at WOT. ive also tried another tps and same thing the previous owner did the swap and the harness conversion im just stumped though because it was running fine till i swapped everything

@H.ALHOSNI 7 лет назад

شكرأ جون , كان هذا مفيداً جداً :)

@roadworthy6901 7 лет назад

Clear and concise, great video!

@GarageBuiltHondas 7 лет назад

Appreciate the comment!!

@theapexlegend2664 6 лет назад

Garage Built Hondas hey so I'm having trouble with my turbo EF. built b18b bottom b16a head car won't rev past 2500rpm. I bought a new tps sensor and installed today if it's above .5v at closed will this cause the issue I'm having I got pissed and went inside gonna try to fine tune it tomorrow need the car running properly by Tuesday to have it dyno tuned

@GarageBuiltHondas 6 лет назад

Was it running fine then this started happening?

@theapexlegend2664 6 лет назад

Garage Built Hondas no at first I have a code 9 so I changed the distributor and cleared that up. before I changed the distributor or started to do that so I thought once I fixed the code 9 it would go away. so then my tuner suggested that the tps was causing the issue I changed it last night but it still won't Rev past 2500 rpm.

@GarageBuiltHondas 5 лет назад

Any other CEL'S?

@dinosaursdoingtherobot850 5 лет назад

hello. i wounder if you could help me out i bought a new tps sensor for a 95 accord and im getting 5 volts closed and 7 volts open will this still work or will something bad happen ?

@srarcade 3 года назад

Got an engine with no tb so i found a stock ex one in my parts bin. I kept getting 0.01 to 3.2v on my tps. Off the car it was correct- took forever to figure out it was the throttle body itself! The return spring has worn and is no longer tight enough to maintain the correct voltages. I wish this spring was replaceable but its not. Nobody makes a stock 60mm tb anymore except whats left at Honda stores for $350. Junkyard parts will probably fair no better. The smallest cheapo tb is 68mm! Ecu will not like that or will it??

@Mishakol1290 3 года назад

Mine read 0.06 with it unplugged and wired to the TPS plug and 0.56 plugged in and set to the maximum position Would this mean its accurate?

@kurtmakeemhurt6657 2 года назад

Really like the jjumper harness. Was just thinking about making one today while I was surfing the tube. I basically have to have one so I don't mess with my rywire harness. Also, you install, or have any videos on installing AEM or aftermarket ECT sensor? Trying to find location. I'm wondering if I can install where oem is and use the blue wire to tap into the ecu with hondata. Thanks from San Antonio.

@Iseekoutthetruth Месяц назад

Where Did You Get The Tester Plug and the Male Connectors To Plug Into The Tester Plug. This Is The best How To Video I Have Found On RU-vid.

@GarageBuiltHondas Месяц назад

The gator clips I got from Lowes. The extra plug from old parts cars I've junked.

@bryanchannell7715 6 лет назад

Thanks for the video bro

@GarageBuiltHondas 6 лет назад

You're welcome!

@husanainawais8293 8 месяцев назад

Hello my honda civic 97 stock tp voltage on idle minus -0.62 are the values ok

@alexbland1312 5 лет назад

I’ve got a 2000 Honda Civic Cp ex, I can’t get anything lower than an 8.3 on the vehicle and I’ve tried grounding it on the negative post and have tried connecting it to the black and yellow wire. My car isles high and won’t go anything higher than 2.3k rpm it bogs down when I do any suggestions?

@Scooter_built 4 года назад

I used two tps and they both wouldn’t adjust past .22. The 2nd one I used didn’t move at all. Wide open like 3.5... are they both bad? It was fine before I swapped my engine same tps

@jackdunn7652 7 месяцев назад

Question, my battery is relocated to the trunk. Can I use the negative terminal on a spare battery that is not hooked up to the car?

@oscarreal9163 Год назад

Hi guys so i have an 08 civic and i was messing with my cold air intake.....now i have multiple symptoms... Engine accelerating on its own while in drive bad shifts slight overheating.....a maf code that isn't accurate.....i replaced it 3 times..............( i didn't really move much any suggestions?? And lower and rougher idle............

@cedriccope178 Год назад

Yeaaa gonna need your assistance on this on my car

@GarageBuiltHondas Год назад

It's easy

@cedriccope178 Год назад

Need to borrow the mini saw then

@cedriccope178 Год назад

Please

@chicolopez939 Год назад

How do i adjust drivebywire throttlebody 2014accord v6???

@biasb3882 4 года назад

What are those bits at the end of that harness you made up called ? I'd like to buy some to make a harness like this. The parts that are pushed into the original parts. The ones after the alligator clips

@GarageBuiltHondas 4 года назад

I got them from some old honda plugs and de-pinned the plug. I believe they were from a distributor plug.

@strickracing437 7 месяцев назад

What if the new tps is showing 0 v at closed and 3.34 wot

@azizullah2579 2 года назад

Thank you Sir

@GarageBuiltHondas 2 года назад

Hope it helped Aziz

@davidtheinspector 5 лет назад

Thank you for your video! Very informative! When de-enrgized mine appears to be about 1/16 of an inch open. Is that normal? Or should it be fully closed?

@GarageBuiltHondas 5 лет назад

That's normal. It'll always have a slight opening.

@spencersgarage 4 года назад

About that TPS testing plug you created, I’m wanting to create one like that myself. I’m not following how exactly that works. You plug it into the TPS sensor you want to test, use the alligator clips for the multimeter you hook up to, but what and how do you hook up the other three wires too without splicing into the harness?

@GarageBuiltHondas 4 года назад

If you see in the video, all 3 wires now have the metal leads on the end. I slide those right back into the original TPS plug to create the connection.

@spencersgarage 4 года назад

Garage Built Hondas ok I got that part of it. Now where did you source the male ends that plug into the engine harness?

@GarageBuiltHondas 4 года назад

De-pinned from another plug. I cannot remember which because I have a box full of connectors, but obviously ones that are male ends.

@mxracingunlimitedltd7784 4 года назад

0.50V IDLE - 4.50Volts WOT. 5V Supply All B/D Series 3-Pin TPS set procedure. Apply +/- voltage to two wires, read voltage from 3rd wire. KOEO. Adjust TPS as needed.

@jayville_2424 4 года назад

Does anyone have a vid for throttle position senor on the hybrid Honda?

@davidheaton2215 3 года назад

Love your videos man!!! Great info!!! I'm a proud owner of a 2000 crv too. Love it. Anyways i just adjusted my tps and closed i get.52 and wot 4.6. Is that ok??? And while i had the throttle body off i ran down the fast idler valve. Was just wondering your thoughts on that if you think that is ok. Thanks

@GarageBuiltHondas 3 года назад

It's close enough and will be just fine. 👍

@z06king 5 лет назад

for public interest, if you change the TPS and just eyebalL the voltage, your car WILL BE STUCK IN PARK AND YOU HAVE TO USE THE KEY RELEASE! ARRRRRGGGHHHH!!! But if you do as GBH has shown,it will shift out of park normally. SSSwweeeeeet!

@rene6399 5 лет назад

So if I don’t have what u made to check the volts would I just have to check but direct wire contact ? Or how would that work ? If not can I just replace it and if I did replace it would I still have to check the specs

@GarageBuiltHondas 5 лет назад

You need a multimeter to check and set it. There isn't any other way.

@austinbates247 Год назад

I got a 96 civic ex upgraded intake and throttle body was 64mm stock OEM upgrade to a 70mm alpha body that was the smallest I could find anyway I got my meter set to DC volts 20 and key on position and negative on batter and my red lead on my red wire (middle of the three) and I’m getting 0.00 on bare wire but when I touch red lead off of the rubber coating for wire it picks up 1.00 something flops around does this indicate I have a wiring issue? Because if so why didn’t tit mess with my last throttle body

@austinbates247 Год назад

@Garage Built Hondas

@renaissancemaneric8019 Год назад

I'm struggling to find the right setting on my multimeter. Another video showed 12V. You said "volts" but I can't see which one in this video.

@CivicBurner410 5 лет назад

I gotta check engine light on my 97 prelude and got a code of 45. my car idle when starting up is grrr ruuu grrr so I cleaned my aivc (twice) still same issue. I bought a tps and of course it's installed using rivets. once car is warmed up it runs fine but occasionally it won't accelerate then kicks in. Am I going into the right direction in replacing this sensor? idk it was adjustable, simply just a sensor. I seen you break the rivets loose by creating a slot and twisting to left but will it tighten back up by just going right? thought rivets were threadless?

@GarageBuiltHondas 5 лет назад

The throttle body is threaded. You can reuse the old hardware if it's still in good enough shape. I usually replace them. Is your code 45 for the TPS? If it is, then this could fix your weird idle issue. The TPS can cause an erratic idld if it's not working properly.

@Bdogg0920 5 лет назад

I got a 95 civic dx When I go to the yellow wire I get 5.02 but on the red I get 0.2 closed and open 2.something and I can’t get any higher than that.. Why is that ?

@Scooter_built 4 года назад

Bdogg0920 same!

@mjcsk8725 4 года назад

I have a 1991 civic lx dpi we're do I buy a tps replacement I have order the wrong one every thing is pointing to a new throttle body.

@GarageBuiltHondas 4 года назад

rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F222444311867

@TheJdmfreek 2 года назад

I have CD5 with a H22A So if i unplug the tps there is no change

@rebeccavaldez5607 6 лет назад

My husband hadden vladamir 3rd and I have a question can a mpfi throttle body be used for a dpfi set up because my husband cracked the connection to what we both think is a Map sensor at the rear of the dpfi throttle body and is a difficult part to locate and replace as well as a complete throttle body assembly unit....please help with any suggestion also we replaced the coolant temp sensor but the connector on the wire harness cracked and trying to locate a replacement pigtail

@GarageBuiltHondas 6 лет назад

No, the TB is completely different on the dpfi setup. It's an oddball. The sensors can be bought brand new, that's the only way to fix a broken connection on them.

@LuisA.Socarras861 2 года назад

To remove the factory screws you can use a cutter, that's what I do, apply a pressure on the screw side and twist. Other people use nose pliers

@GarageBuiltHondas 2 года назад

👍

@rendiix4269 4 года назад

Hey man i just fixed my civic 91 change gas pump and head gasket but when I accelerate just a little at low revs the car drowns out a lil & if I accelerate hard works well do you think I have to adjust the throttle body?

@GarageBuiltHondas 4 года назад

You can try it. Any CEL's?

@rendiix4269 4 года назад

@@GarageBuiltHondas no codes all sensors working

@jashansuvarna9599 Год назад

is it okay to remove the tps from the oem throttle body? my tb needs replacing but the after market one i have needs both sensors to be put on the new throttle body and the tps looks revited.

@GarageBuiltHondas Год назад

Yes it's ok.

@thesoulxsociety5068 5 лет назад

Would a bad tps gasket cause the vehicle to die on a cold start? It only happens when cold and if I spray some brake clean around the tps it makes the idle change.. Just wondering if you've ever run into that issue before, I should probably add that this is on a dual point style

@GarageBuiltHondas 5 лет назад

It does sound like a vacuum leak of some sort especially with the fluctuating idle with the brake cleaner. I'd check the gasket first.

@7ThrillFishing 5 лет назад

Could the tps be causing my car to idle high? I have the tps code and map code but the map sensor I replaced but still reading the code. Could a bad tps trigger the map sensor?

@GarageBuiltHondas 5 лет назад

It's possible, but unlikely. Try to get it fixed first and if the idle is still high then you.knownits not the TPS.

@ClaireFuze 3 года назад

On your bswap did you have to swap the green and yellow wire on the tps?

@GarageBuiltHondas 3 года назад

When doing an mpfi setup in a dpfi chassis, yes.

@hondas8447 6 лет назад

How about a d16y8 .what are numbers for the throttle body closes please

@GarageBuiltHondas 6 лет назад

+Arturo Garcia same. .5 and 4.5. 👍

@sapphiresnape7456 4 года назад

do u have a video showing the actual install of a new one ?

@GarageBuiltHondas 4 года назад

I don't

@philipdaigneault6822 6 лет назад

Im calibrating mine right now, does it have to exactly on .50 and 4.50

@GarageBuiltHondas 6 лет назад

Those are oem specs, anything close will be ok.

@Streetflowautomotive 4 года назад

Where can I find the tips you spliced at the bottom?? Love that custom tool

@GarageBuiltHondas 4 года назад

I got them at harbor freight. Thet probably sell them at your local auto parts store too. Gator clips!

@brianklassen8585 3 года назад

Great videos, thanks. We have an '88 CRX non si model. At the end of the video you show a TPS with plug facing left, that's ours! So, what do we do then? switch the outside wires?

@GarageBuiltHondas 3 года назад

No. You need to find a dpfi specific TPS. There is no other option.

@brianklassen8585 3 года назад

@@GarageBuiltHondas I found this

@brianklassen8585 3 года назад

www.xasitur.com/index.php?main_page=product_info&products_id=55136&fbclid=IwAR08AJSsZPQ22NmuHH-KWjMS9ESk6dUwyB8MqewM9w5Tyx2T1Bo23JXhkjM

@casparvester6278 6 лет назад

John love you vids some of the best I have seen. You seem like an old school guy but curious you ever dabble in k series ?

@GarageBuiltHondas 6 лет назад

+Caspar Vester Thanks Caspar! I haven't had the opportunity yet! I'd love to have one and learn how to do the swap into an EF. Possibly one day, but nothing immediately planned.

@casparvester6278 6 лет назад

Garage Built Hondas Thanks for the reply I feel like I’m talking to a celebrity haha Keep up the great content love the channel

@GarageBuiltHondas 6 лет назад

+Caspar Vester Haha, thanks for the vote of confidence, but I'm just a regular guy like you, playing with some fun Hondas!

@franz-motovlogs3516 5 лет назад

what if the voltage is change when the engine is start example if my voltage in of engine is .73 in close position and when engine start the voltage is up in .86-87 is that normal or i need to change my tps

@GarageBuiltHondas 5 лет назад

It sounds off. Does it idle high or have any strange symptoms?

@cole-ih3vp 4 года назад

I’m having the same problem. Closed it’s at .7 open it’s at 4.5

@jairotorres1145 6 лет назад

My car goes on limp mode at around 2000 rpm but my tps was never connected since I had the car but once I connected it ,it started limp mode any idea?

@GarageBuiltHondas 6 лет назад

+The Gaming Kid are you getting a CEL for the TPS?

@lynndsiecornelius2904 2 года назад

Is there any other way to get the TPS off if you don’t have a thing to grind lines in it? That’s where I’m stuck.

@GarageBuiltHondas 2 года назад

Not really. You could grind it off completely. Maybe a chisel and hammer.

@ClaireFuze 5 лет назад

Not sure if you'll see this or not but I just wanted to know if your bswap was done with a civic si or an ex? I'm helping with a swap on a 91 si and everyone's telling me I need to do the dpfi to mpfi conversion and I'm telling them all no I don't. Having a helping comment from. You would go along way

@GarageBuiltHondas 5 лет назад

I see em all, but looks like I got you on IG first! 👍

@ClaireFuze 5 лет назад

@@GarageBuiltHondas that you did. Thanks alot haha knew I wasn't crazy

@leonelobbed 7 лет назад

In order to get wide open throttle reading I need to change the wire im testing? Or is it the same as with the 4.5 closed reading one?

@GarageBuiltHondas 7 лет назад

same wire, WOT should be 4.5, and .50 closed.

@leonelobbed 7 лет назад

J Wid Films then for some reason it doesnt change voltage when I open it. What could it? Im not having tps problems btw just swapping ny oem tb

@GarageBuiltHondas 7 лет назад

The connection is good?

@leonelobbed 7 лет назад

J Wid Films Im not sure, i just punctured a little hole to my red and black wire. Its an RSXS

@GarageBuiltHondas 7 лет назад

Maybe take off a little more of the sleeve to expose more wire and see if that helps the connection.

@khashirlatif1825 5 лет назад

Thanks fine information sir👍

@GarageBuiltHondas 5 лет назад

Thank you

@laine93dahatchback75 4 года назад

I have a 93 integra ls, which is the same manifold and throttle body on your car, will my tps readings need to be the same as yours are? Planning on installing a new intake manifold, throttle body and tps this weekend and want to make sure before I do it.

@GarageBuiltHondas 4 года назад

Yes

@laine93dahatchback75 4 года назад

@@GarageBuiltHondas awesome, thanks man, I appreciate it. Contemplating maybe doing videos of the progress of my car, there isn't a lot of da hatchbacks on youtube with guides on how to do stuff

@GarageBuiltHondas 4 года назад

Nice, it could be fun for you just to enjoy making videos also.

@Jay-jd4ge 3 года назад

Is it possible to use an impact screw to make a slit?

@GarageBuiltHondas 3 года назад

It might work, but my guess is probably not.

@mngsadventur3364 4 года назад

Need help first time doing this but I have a 92 civic vx hatchback the throttle body is much smaller I bought an ek arm intake which is alot more wide open then the eg one can I just swap out the ek throttle body to my eg which they just bolt right on ?

@GarageBuiltHondas 4 года назад

I'm not sure if it'll fit. Might be too big. The arm will fit, you might just need a silicone reducer.

@mngsadventur3364 4 года назад

@@GarageBuiltHondas thanks for the response but sadly the ek throttle body is much wider so I wasnt able to just bolt it right up so now I think my option is to either try finding the ex manifold n see if theres is bigger or just go buy an intake for the 1.5 leter intake

@GarageBuiltHondas 4 года назад

Are you talking about an intake arm and filter?

@TheFortis3 6 лет назад

hey bro.....my tps will only let the vehicle rev out close to properly when the voltage is 0.7v closed!...when i set it at 0.45v closed,it seems to go in limp mode and bog out at 3500 rpm. what you think could be wrong?

@GarageBuiltHondas 6 лет назад

This didn't make any sense to my brain.. "only let the vehicle rev out close to properly when "? Help me out here.

@TheFortis3 6 лет назад

sorry...lol that is how we talk in jamaica...but when i set my tps at 0.45 to 0.50v with the throttle plate closed, it bogs when i raise the rpms at 3500. its like i cant raise the rpms smoothly unless i set it at 0.70v closed

@GarageBuiltHondas 6 лет назад

Jamauto tech Na, you're good! It just didn't compute in my head when I read it. Was your car running fine before adjusting it? It's showing .70 closed, and is it 4.70 at WOT?

@gilliammark5083 4 года назад

Does anybody in the group have a 1999 Acura CL 2.3 or similar? Wanted to see how your car ran after you put in the new Throttle body position sensor.

@rickharrison6969 6 лет назад

Can the tps cause slight rpm hunt at 1500 rpm down 100 rpm to 1400 rpm and sorta be stuck in that small loop until I give it more gas or let up on the gas? This only happens at a slight pressing down of the gas pedal and keeping it that consistent speed

@rickharrison6969 6 лет назад

I have a video on my channel that shows what happens with the tach

@GarageBuiltHondas 6 лет назад

+Rick Harrison if you're applying gas and it's moving, does it feel like the transmission is slipping? Any CEL's?

@rickharrison6969 6 лет назад

Garage Built Hondas no cels that I am aware of, if I press on gas and hold it at this certain speed and in 4th gear, it doesn’t feel like it’s slipping as it’s already shifted into the gear, but it’s at the lower end of the gear and if I hit the gas a little faster it accelerates and gets unstuck from that loop

@aTastyBiscuit 5 лет назад

i have a '00 civic coupe with a d15b and it has a tps low input code. there would be uneven idles and constant jerking of the car when i'm driving so the mechanic i usually go to replaced the tps sensor. afterwards, it was driving fine but i still noticed a little bit of jerking while driving and it eventually went back to before so i brought it to the mechanic again. he calibrated the voltages with the multimeter and a few days later, it's back to uneven idles and jerking while driving. i'm not sure if i should go back to the mechanic or look for a new one. the code still reads as tps low input. what do you think is the problem?

@GarageBuiltHondas 5 лет назад

Is that the only CEL you're getting?

@aTastyBiscuit 5 лет назад

@@GarageBuiltHondas"tps low input" is the only code that shows up upon scanning.

@bradleybaynard5536 2 года назад

@@aTastyBiscuit did you ever figure it out? Same problem here

@561Rockout 3 года назад

Hey question, I have a 97 Acura cl and Lately it’s been having issues starting, now I thought it could’ve been bad gas or something along those lines but I put in the cleaner and put premium gas in the car and it still doesn’t wanna start right, the battery, and starter are good, I was wondering to see if this would help because my rpms are also not always at a set spot and will jump a lil sum times I really couldn’t find much on the issues beside the TPS also it seems to do it after the car has been running like if it sat overnight it would start right up, but if I drove like an hr + than leave it for like 20 minutes it does this.

@GarageBuiltHondas 3 года назад

Any CELs?

@561Rockout 3 года назад

@@GarageBuiltHondas nope

@561Rockout 3 года назад

The only light I have is my abs light but I changed my brakes and not rlly worried about it

@zkmoonea 2 года назад

may be some issues around the throttle body. the throttle body sensor, the throttle open and close mechanism, etc.

@itr_cloud 7 лет назад

the lowest reading I can get at closed is .60x and at wide open is 4.76 this doesn't seem right do I have a defective TPS?

@GarageBuiltHondas 7 лет назад

You followed the steps, correctly plugging each wire in correctly and still getting those readings?

@itr_cloud 7 лет назад

Jon Widmer yes I probed into the red wire and got those readings

@jedward1694 3 года назад

What does the TPS affect when in a bad position?

@GarageBuiltHondas 3 года назад

Bad position?

@leoampil 3 года назад

Do you know where can i buy the tps for dual point?

@GarageBuiltHondas 3 года назад

I used to see some on eBay. Check there. He was asking quite a bit but I don't think they are easy to find anymore.

@Highway94 5 лет назад

So I don't necessarily need to buy one ? I could just " Adjust " it and everything hopefully will get better?

@GarageBuiltHondas 5 лет назад

More than likely no if you getting a check engine light? But it doesn't hurt to try it.

@gervaisbilodeau8465 3 года назад

Been trying to calibrate the TPS. Cannot set it at .5 volt. The lowest voltage I get is 1.6 volt with the throttle fully closed. Fully opened, the reading is over 5 volts. I think I bought myself some troubles. Looks like the alternator has an issue too at high speed. Battery warning light blinking. Transmission shifts at over 3000 rpm...when it does. And downshifting to first gear is harsh. Oh my. 😟

@GarageBuiltHondas 3 года назад

Shouldn't be too much changing some of those sensors.

@tstrotstro5038 Год назад

Thank you in 2022

@joshpalmer9184 4 года назад

91 Honda Accord ex f22a4 I replaced mine tps sensor I got 4.5 v close open 0.5 v what am I doing wrong need help

@GarageBuiltHondas 4 года назад

Try swapping the wires around

@brandonbassett7887 7 лет назад

.my car is a 98 civic with lsv. i got code 7 for tps sensor, has a new tps sensor i can see why its off. but am i correct that this is the most likely cause of limp mode cuz this adjustment is off?

@GarageBuiltHondas 7 лет назад

Doesn't seem like it would. Check the wiring at the distributor, make sure none are loose or in need of repair. Have you taken it to Autozone? They'll run the obd2 scanner and it should point you in the right direction where the problem is.

@brandonbassett7887 7 лет назад

Jon Widmer i heard i have to pull codes by counting the flashes, at the ecu pin which i did. Igot a 98 civic ex harness b16 head and b18block

@brandonbassett7887 7 лет назад

Jon Widmer dizzy is a b16 obd1 with dizzy jumper. And running p28 chipped ecu

@brettbeaver103 7 лет назад

Brandon Bassett hey man I got the same code with my car in limp, did you figure your problem out?

@rebeccavaldez5607 6 лет назад

Okay thank you .....

@minty_lobsta 4 года назад

What happens when you get insane voltage on both open and closed?

@GarageBuiltHondas 4 года назад

Sure you're testing it correctly?

@zokvsha6902 4 года назад

Awesome video! Also, how would I do this without your special tool?

@GarageBuiltHondas 4 года назад

You'll need to remove some of the casing of the wire to be able to get a reading.

@Atah714 7 лет назад

What if the tps reads .5 to 4.1 wide open but won't turn anymore? 03 Honda civic 1.7l

@GarageBuiltHondas 7 лет назад

I'm not familiar with those civics, does it have a throttle cable still?

@Atah714 7 лет назад

Garage Built Hondas yes it has one.

@Atah714 7 лет назад

Garage Built Hondas after putting it back on with the above measurements the code cleared and the threw up a p1106 baro curcut 1 of 2 code both the same

@GarageBuiltHondas 7 лет назад

+Atah714 try this. www.engine-codes.com/p1106_honda.html

@rendiix4269 4 года назад

Hey man i have code 4 on my 1991 civic DX D15b2 were is the crank position sensor located

@GarageBuiltHondas 4 года назад

Inside the distributor

@rendiix4269 4 года назад

@@GarageBuiltHondas can i replase just the sensor or all the distributor

@JESC-RV 3 года назад

Do you know if installing the TPS sensor without calibrating it will cause bogging issues?

@GarageBuiltHondas 3 года назад

@bradleybaynard5536 2 года назад

Ever find out anything? I’m bogging

@JESC-RV 2 года назад

@@bradleybaynard5536 I had a bad ECU

@MigsJ19 6 лет назад

This is an old video but I was wondering if you could help me. My tps output signal is very low varying between 0.05 to 0.08 at Closed throttle and it doesn't change when I open up the throttle. Ive checked and I'm getting 5 volts on the positive and negative wires. So would that mean my tps has gone bad? It's also fairly new and was working. If not then any other ideas you might have would be much appreciated.

@GarageBuiltHondas 6 лет назад

Do you have another one you could check also? If it's giving you those readings it almost sounds like it is faulty. You're multimeter is setup correctly and all connections fine?

@MigsJ19 6 лет назад

Garage Built Hondas thank you for responding and I do but it's one I randomly found in my box of bolts and things. Its prbly faulty as well, because it reads exactly the same. Yup the multimeter and all connections are as good as can be. So it's most likely faulty tps then

@GarageBuiltHondas 6 лет назад

You know, head to the auto parts store and buy one, come home and test it out. If it's still giving you the same reading then something else is wrong and you can take the TPS right back and get your refund. 😀

@MigsJ19 6 лет назад

Garage Built Hondas that's what I was thinking, thanks man :D so if that ends up being the case, could it be the ecu?

@GarageBuiltHondas 6 лет назад

Probably not. More than likely a wiring issue.

@JodBronson 6 лет назад

THANK YOU VERY MUCH FOR THE TIPS: @ 0:40 :)))))))))))))))))

@GarageBuiltHondas 6 лет назад

You're welcome!

@LsxOscar 7 лет назад

if my tps adjustment is off can i cause a misfire?

@GarageBuiltHondas 7 лет назад

Possibly, but usually not at all. I've just thrown the TPS on before with no Adjustment and didn't have problems. It is possible though.

@christophervillegas7640 3 года назад

Oh you're A MECHANIC mechanic

@GarageBuiltHondas 3 года назад

24-7

@tco8183 5 лет назад

I have the dpfi...what does it mean if I disconnect the tps and it dies? Problems in seeing is bucking at acceleration (eventually stalling) and very rough idling.

@GarageBuiltHondas 5 лет назад

Any CEL's?

@tco8183 5 лет назад

Garage Built Hondas none at all. I read that it should run still, mine dies. The TPS is within spec on the meter, just didn’t know if I could rule it out completely yet. Idling since then has improved but the hesitation at acceleration persists, bucking and jerking when I need the rpms to climb

@GarageBuiltHondas 5 лет назад

I doubt it's the culprit. New electrical tune-up parts lately? Or older parts?

@tco8183 5 лет назад

Junkyard dizzy and a junkyard IACV, just to see if it made a difference...same prob. But I’m thinking there’s a timing problem. Just noticed There are the factory three ignition timing marks, and some home-made timing marks lol the dizzy fully advanced is aligned with the homemade marks, fully retarded it aligns with the factory marks. Bucking while accelerating occurs at both so I’m stuck...I want to believe the factory marks but it needs to be at fully retarded timing to reach it. Ever seen that before? Can’t afford a swap yet, hoping this engine would tough it out a bit longer

@raymondcamacho2720 4 года назад

Hello I just install my TPS was wondering I have it adjusted to. .49v but when I open my throttle it read 4.17 any thoughts? Awesome video tho.

@GarageBuiltHondas 4 года назад

Try to adjust the position that its mounted, you may be able to achieve the correct settings.

@raymondcamacho2720 4 года назад

@@GarageBuiltHondas I try. I'f I let it be a .49v close 4.18 WOT it giving me an idle surge drop up and down 200prpm to 1000prm. If I tap TPS a bit it stop surfing but idles at 2000rpm flat. Clean out iacv and will be flushing coolant next. Any other suggestions?

@GarageBuiltHondas 4 года назад

None but possibly a different tps. Is everything completely stock?

@raymondcamacho2720 4 года назад

@@GarageBuiltHondas yeah everything is stock. It is a D16 motor. I order a new iacv with another Tps to see it helps.

@GarageBuiltHondas 4 года назад

Sounds more like an IACV or FITV issue. Your car may not have an FITV though.

@supermario7346 3 года назад

I'm currently attempting this, but those damn screws are very tight. Even using the dremel and screwdriver method, they just won't budge. Think I need to use an impact driver like you did?

@GarageBuiltHondas 3 года назад

Try it.

@supermario7346 3 года назад

@@GarageBuiltHondas ended up visiting my local mechanic who kindly agreed to unscrew them for me for free lol

@GarageBuiltHondas 3 года назад

👍